🛠️ What did you do to your Tremor today? [2026 edition]

img_9854-webp.264061
Turned out great! Love the wheels.
 
Turned out great! Love the wheels.


Thanks, man!

After looking again at the rear axle hub, covered in 🏕️ dust that had been hiding under the FORD hub cover, I'm headed over to the parts store for a can o' this -

VHT satin black roll bar - chassis paint.webp


I think it being Satin Black will best match the front WARN hubs' finish. Either way the brown full-floating axle hub poking out has become an eyesore. lmao.

must. fix.


😝
 
Thanks, man!

After looking again at the rear axle hub, covered in 🏕️ dust that had been hiding under the FORD hub cover, I'm headed over to the parts store for a can o' this -

View attachment 264172

I think it being Satin Black will best match the front WARN hubs' finish. Either way the brown full-floating axle hub poking out has become an eyesore. lmao.

must. fix.


😝
I keep meaning to paint mine.... 🤷
 
I keep meaning to paint mine.... 🤷
After contemplating removing my factory exhaust tip and sending it out for cerakoting, I went the easy route and hit it with rustoleum high heat paint. Several months on, it still looks fine after 6,000ish miles, rain, a few car washes etc. I wouldn't hesitate to paint the hubs after my experience.
 
the Carli end links have been known to self-disconnect


Duly noted.

I ordered the full kit Carli torsion sway bar and received last week just the bar, the female, splined, bar end levers (black wrinkle powdercoat), the billet aluminum frame mounts and the Delrin bushings but no endlinks. Hence my deeper dive which netted mixed opinions. The Carli billet steel endlinks arrived yesterday to my ultimate relief.

I finally remembered to contact CJC while they were open during business hours to get that third opinion I joked about earlier and was told the shorter, LVL endlinks are what I should use on my factory-height Tremor Super Duty; that the Ford endlinks do not have enough articulation at each end, and that the mount studs are too small a diameter for the Carli bar ends' mount boss bores.

So, in they go and I'll pay extry attention to Carli's SPECIFIC endlink joints' pre-install adjustments specified on their instructions sheet. Then monitor their condition every oil change if not more often at first.

Thanks for the heads up, as always.
 
Duly noted.

I ordered the full kit Carli torsion sway bar and received last week just the bar, the female, splined, bar end levers (black wrinkle powdercoat), the billet aluminum frame mounts and the Delrin bushings but no endlinks. Hence my deeper dive which netted mixed opinions. The Carli billet steel endlinks arrived yesterday to my ultimate relief.

I finally remembered to contact CJC while they were open during business hours to get that third opinion I joked about earlier and was told the shorter, LVL endlinks are what I should use on my factory-height Tremor Super Duty; that the Ford endlinks do not have enough articulation at each end, and that the mount studs are too small a diameter for the Carli bar ends' mount boss bores.

So, in they go and I'll pay extry attention to Carli's SPECIFIC endlink joints' pre-install adjustments specified on their instructions sheet. Then monitor their condition every oil change if not more often at first.

Thanks for the heads up, as always.
I suggest adding a bit of loctite on the end link caps so they don't unscrew. My shop also found that they were arriving to them a little under greased, so add some grease to them via the zerks to fill them up. It's now something I plan to do annually is to regrease the end links.
 
I suggest adding a bit of loctite on the end link caps so they don't unscrew. My shop also found that they were arriving to them a little under greased, so add some grease to them via the zerks to fill them up. It's now something I plan to do annually is to regrease the end links.
As @DTX2023Tremor stated - Use some loctite on the link threads, they are prone to coming undone. I know the engineers at Carli are aware of this. So I assume they will be solving for it in short time.
 
After looking again at the rear axle hub, covered in 🏕️ dust that had been hiding under the FORD hub cover


IMG_9854.webp


Until better weather for painting, I was early to a Sat morning caffiene cruisers and brought a bucket and a rag. I simply wiped away the dust to reveal a thinly-applied (VERY thinly) assembly-line satin black paint coat.

IMG_9873.webp


I can't wait! to paint these things but when just cleaned they look better.
 
Changed the engine oil/filter, Shell T6 5W-40. Winter will be in full swing (or over) by the time I need to change it again.

You would think a 65 year old man could do this job without spilling a drop. I've been changing PowerStroke 6.7l since 2011, so it's not a lack of experience. I buy every gadget that claims to make an oil change cleaner, neater, or faster. Fumoto valve certainly doesn't make it faster, even with oil at normal op temp.

Most of my problem is a breeze blowing a slow drip away from the drip pan or taking off the filter. I tried the gallon ziplock bag around the filter last time, meh. Today I used a metal drip pan, supported by a milk crate. The oil on my hands is what dripped on the driveway. Maybe I should try the gallon bag again with the elevated pan. One day I'll get it figured out.
 
Changed the engine oil/filter, Shell T6 5W-40. Winter will be in full swing (or over) by the time I need to change it again.

You would think a 65 year old man could do this job without spilling a drop. I've been changing PowerStroke 6.7l since 2011, so it's not a lack of experience. I buy every gadget that claims to make an oil change cleaner, neater, or faster. Fumoto valve certainly doesn't make it faster, even with oil at normal op temp.

Most of my problem is a breeze blowing a slow drip away from the drip pan or taking off the filter. I tried the gallon ziplock bag around the filter last time, meh. Today I used a metal drip pan, supported by a milk crate. The oil on my hands is what dripped on the driveway. Maybe I should try the gallon bag again with the elevated pan. One day I'll get it figured out.
If only we could trust jiffy lube (or whatever regional quick change).... 🤦
 
As @DTX2023Tremor stated - Use some loctite on the link threads, they are prone to coming undone. I know the engineers at Carli are aware of this. So I assume they will be solving for it in short time.
Mine just came undone
 

Attachments

  • 20260722_162954.webp
    20260722_162954.webp
    277.9 KB · Views: 57
Trying out an anti rattle hitch pin for the first time. Went with this One. I love the idea of. We shall see how much I like it.
 
Summoned again by @Battle Born Offroad. The brand new Morimoto XRBG EVO LED headlights are installed and ready to brighten people's night 🤪.


View attachment 263320
View attachment 263321

These things are awesome. I love the start-up sequence as well as the RGB feature. The illegal superchargers are also installed. I get flashed enough as it is but these will take it to a whole notha level!

View attachment 263305
View attachment 263307

Chas doing the video shoot.

View attachment 263312
View attachment 263324
View attachment 263308
View attachment 263309View attachment 263310
View attachment 263311

I want to thank Morimoto for reaching out to @Battle Born Offroad. Chas and his crew needed a truck and voila! My baby got new flashers.

Thank you brothers for making this happen. Video content coming soon 👊.

View attachment 263326View attachment 263327
I like those. Also what fog light kit is that
 
I like those. Also what fog light kit is that
Thank you brother!

It's the BMC kit:



 
View attachment 264284

Until better weather for painting, I was early to a Sat morning caffiene cruisers and brought a bucket and a rag. I simply wiped away the dust to reveal a thinly-applied (VERY thinly) assembly-line satin black paint coat.

View attachment 264285

I can't wait! to paint these things but when just cleaned they look better.
That truck looks perfect the way it is. Do not change anything. 👍
 
Back
Top Bottom