🛠️ What did you do to your Tremor today? [2026 edition]

Agh. Trying to re-up my FORScan license. Many small struggles.

When the sun drops a bit in the summer sky, I'll go out to my truck and actually plug FORScan in, THEN see what happens. Meanwhile, I'm in my office, here, an elderly person recovering from a 500-lb tire humping session X 4 today.

I sit down. :ROFLMAO:


I want to drive my truck but I'd rather get the necessary FORScan changes in place before I do.
 
There is no way he was stopped for speeding. :ROFLMAO:
1000016683.gif
 
1000019760.webp

I have 10,800 miles on the truck now and just returned from a trip that included 300 miles of trails. It was time to clean off the engine bay.

On a cold motor, I put a crumpled up trash bag in the intake opening, rinsed everything off with a cone spray with a garden hose, spray everything down with Simple Green (avoiding painted ares), rinse off with water, then finally blow off water with a leaf blower. Go for a drive! I've been doing this method for decades with many vehicles and have never had an issue. No other engine prep necessary.
 
do you make one of those for a 2022 and will it work with a lubelocker gasket ? is it a modified o.e.m. cover ?
we only uses OEM Axle Covers, modify them to add various bungs per request.
OEM sized gaskets will work, lubelocker for example
 
Are f150 side step brackets shorter than tremor f250 brackets?
 
View attachment 263899
I have 10,800 miles on the truck now and just returned from a trip that included 300 miles of trails. It was time to clean off the engine bay.

On a cold motor, I put a crumpled up trash bag in the intake opening, rinsed everything off with a cone spray with a garden hose, spray everything down with Simple Green (avoiding painted ares), rinse off with water, then finally blow off water with a leaf blower. Go for a drive! I've been doing this method for decades with many vehicles and have never had an issue. No other engine prep necessary.
You know....we've got a couple of solutions on our site for that intake opening...

 
Are f150 side step brackets shorter than tremor f250 brackets?


I cannot answer that directly, but there is more "door" on the bottom of the Super Duty door than there is below the body line of an F150 door. But that could be due to the Super Duty's slight increase in head room.

What is it you're trying to do? I like where this might be going. 😝
 
Today, I WILL ATTEMPT to square away my FORScan program; having trouble importing my license update from my laptop to FORScan so that I may use FORScan to update my tire circumference then the three relevant module re-learns.

Another thing I will try to get to today is to finish up the install of my Carli torsion sway bar - I'm getting mixed info if I may use the factory Tremor swaybar endlinks or if I have to use the (perhaps slightly too long?) 2.5" Carli billet stainless megaoverkill endlinks for my factory Tremor front suspension ride height... guess I'll call CJC again and see if a third person there might tell me something different than the first two.

Hee. Nobody's on the right page.
 
Are f150 side step brackets shorter than tremor f250 brackets?
No, they are not. F-150 side step brackets are the same length as F-250 Tremor brackets.

While F-150 brackets are indeed significantly shorter than standard F-250 or F-350 brackets (which drop the boards about 1.5 to 2 inches lower), Ford specifically used the shorter F-150 length brackets for the Super Duty Tremor package. This was done to tuck the Raptor-style, high-clearance running boards closer to the rocker panels and improve the truck's breakover angle for off-roading.
 
Ford specifically used the shorter F-150 length brackets for the Super Duty Tremor package.


Thought so, but with Jack's question I re-thunk it. :ROFLMAO:
 
Are f150 side step brackets shorter than tremor f250 brackets?

Are talking about the running board brackets? If so, I think that they are the same length. I pulled the running boards off of my wife's 24F150 and put on 24F250 Tremor running boards. I didn't measure the bracket length specifically, but visually they look to position the boards in the same plane.

Screenshot 2026-07-30 070742.webp
Screenshot 2026-07-30 070641.webp
 
Today, I WILL ATTEMPT to square away my FORScan program; having trouble importing my license update from my laptop to FORScan so that I may use FORScan to update my tire circumference then the three relevant module re-learns.

Another thing I will try to get to today is to finish up the install of my Carli torsion sway bar - I'm getting mixed info if I may use the factory Tremor swaybar endlinks or if I have to use the (perhaps slightly too long?) 2.5" Carli billet stainless megaoverkill endlinks for my factory Tremor front suspension ride height... guess I'll call CJC again and see if a third person there might tell me something different than the first two.

Hee. Nobody's on the right page.
Maybe @BLACKCHERRY can provide some input on the end links and sway bar?
 
Summoned again by @Battle Born Offroad. The brand new Morimoto XRBG EVO LED headlights are installed and ready to brighten people's night 🤪.


View attachment 263320
View attachment 263321

These things are awesome. I love the start-up sequence as well as the RGB feature. The illegal superchargers are also installed. I get flashed enough as it is but these will take it to a whole notha level!

View attachment 263305
View attachment 263307

Chas doing the video shoot.

View attachment 263312
View attachment 263324
View attachment 263308
View attachment 263309View attachment 263310
View attachment 263311

I want to thank Morimoto for reaching out to @Battle Born Offroad. Chas and his crew needed a truck and voila! My baby got new flashers.

Thank you brothers for making this happen. Video content coming soon 👊.

View attachment 263326View attachment 263327
Looks Sick!!!!
 
we only uses OEM Axle Covers, modify them to add various bungs per request.
OEM sized gaskets will work, lubelocker for example
thank you i will be ordering one of those.
 
yeah-baby-yeah-webp.264059


Success! finally, with using FORScan to recalibrate my speedometer for this nominal 37" tire. Our esteemed colleague McE was the biggest help, there, along with several others who replied to my cry for help: Stroke250, Toxophilite, and HitFactor. Thank you all.

Success, too, in tackling the issue of the tire/wheel package retailer using the wrong wheel weights, and that, after my specific request for "low profile" wheel weights to be used due to the downsize in wheel diameter from 18" to 17". Huge thanks to my local America's Tire dealer for the NASCAR Cup level speed and efficiency for my five-tire spin balance appointment pit stop. 20 minutes! lol.

All that's left for this phase of Tremor enhancements are the Carli torsion swaybar, which is about to get up in there, maybe this weekend.

Tire/wheel picture for you!

img_9854-webp.264061
 
Back
Top Bottom