🛠️ What did you do to your Tremor today? [2026 edition]

Did the first oil change with the Juggernaut skid plate and I have to say it was not a great experience. I think the cutout for the oil filter could be a bit larger, and the cutout for the oil drain should be shifted up toward the front of the truck and over more towards the driver side. Got oil all over the skid plate as I was thinking it would drain like normal - but no. Needed to use a funnel to direct it out. A bit disappointed in that but overall happy with the fit and finish and the protection I will now have. One other issue is having to drop the entire skid plate to change the lower fuel filter.
 
Just had my second oil change done today. First one was at 1000 miles. This one was at 2500 and the next will be at 5,000. After that, every 5K. The first two were free. Thinking about doing the rest on my own and installing an oil valve and using the vac trick!
 
Did the first oil change with the Juggernaut skid plate and I have to say it was not a great experience. I think the cutout for the oil filter could be a bit larger, and the cutout for the oil drain should be shifted up toward the front of the truck and over more towards the driver side. Got oil all over the skid plate as I was thinking it would drain like normal - but no. Needed to use a funnel to direct it out. A bit disappointed in that but overall happy with the fit and finish and the protection I will now have. One other issue is having to drop the entire skid plate to change the lower fuel filter.
I have the Talon skid plate and I used to try to remove the oil filter through the port. I don't bother removing that access plate anymore and just get to the filter from the side. I rotate my tires each oil change, so with the wheel off it is really easy to get to the oil filter. A quart size ziplock bag around the filter helps contain the mess and I just spin it off into the bag.
 
Did the first oil change with the Juggernaut skid plate and I have to say it was not a great experience. I think the cutout for the oil filter could be a bit larger, and the cutout for the oil drain should be shifted up toward the front of the truck and over more towards the driver side. Got oil all over the skid plate as I was thinking it would drain like normal - but no. Needed to use a funnel to direct it out. A bit disappointed in that but overall happy with the fit and finish and the protection I will now have. One other issue is having to drop the entire skid plate to change the lower fuel filter.
i got mine with the cut-outs deleted.

i just drop the whole thing

take/make it an opportunity to inspect & clean it up
 
Did the first oil change with the Juggernaut skid plate and I have to say it was not a great experience. I think the cutout for the oil filter could be a bit larger, and the cutout for the oil drain should be shifted up toward the front of the truck and over more towards the driver side. Got oil all over the skid plate as I was thinking it would drain like normal - but no. Needed to use a funnel to direct it out. A bit disappointed in that but overall happy with the fit and finish and the protection I will now have. One other issue is having to drop the entire skid plate to change the lower fuel filter.

Did you do a fuel filter relocation kit?? :unsure: :unsure: :unsure:

Honestly I just drop the Juggernaut skid plate for my oil changes. Too easy using either a ratchet w/sockets, or even ratcheting wrenches. If I recall correctly 16mm for the oil drain plug, 15mm for 4 of the skid mounting bolts, and the bigger Juggernaut one i want to say is 17mm or standard size....

:cool::cool::coffee::coffee:🇺🇲🇺🇲🇺🇲🇺🇲
 
So... I had requested at the time of sale, "low profile" stick-on wheel weights.

What I got are freaking 1/4" thick lead bricks that contact the brake caliper during a test fit.

The retailer, SD Wheel is apparently a division of Custom Offsets, and had I known...

Anyway, the correct wheel weight request never made it to the mount and balance crew in the warehouse, so now it's on me to correct the issue and try for some reimbursement.

Unbelievable. I waited two weeks for these things to get here; they bumped the delivery day TWICE, and now this. I just want these on my truck already.

Headed to America's Tire in the morning where I have an appointment for a re-balance. Going to load them up in the back and run down on my set of Tremor wheels/tires.

img_9832-webp.263633
Have you tried balancing beads instead?
 
Have you tried balancing beads instead?


My private life is no concern of yours, sir.

Wait... wat?

Oh! You mean... 😝


Nah. I think that's an awfully transient way to depend on a balanced wheel/tire assembly.

We solved my dilemma with a little more tire/wheel tossing labor and a round trip south to a certain Discount Tire location where I had scheduled an appointment. It was first thing in the morning and Asst. Mgr Abel had three guys and two machines on my job. I was impressed.

I was in and out of there in 20 minutes! with the five wheels/tires now having the correct, much thinner, 1/4 ounce stick-on weights and each taking less weight than before from SD Wheel's static balancing job.

Two days later after running local errands I was able to get up onto the interstate for an 80 MPH cruise for a few miles on good concrete and the truck is even smoother than it was when wearing the Duratracs. Win/win.
 
I think that's an awfully transient way to depend on a balanced wheel/tire assembly.


Change my mind.

I just cain't wrap my head around how that becomes a permanent solution. How are they applied or installed? How do they find the sweet spot? How do they STAY PUT.

It seems I may be missing certain factoidials, because some Tremor/Super Duty owners seem to have satisfactory results.


Why, when I first heard the term "tire balancing beads" I remembered when cleaning up a 1920's residential garage finding a dusty old package of something called "ENGINE REBUILD PELLETS".

:ROFLMAO:

...which upon reflection at the time I assumed were "Ringer [engine] Restore" but in solid form that one would drop a few into the bad engine's oil supply where they'd dissolve and then fill in cylinder wall scratches or whatever.
 
Last edited:
Change my mind.

I just cain't wrap my head around how that becomes a permanent solution. How are they applied or installed? How do they find the sweet spot? How do they STAY PUT.

It seems I may be missing certain factoidials, because some Tremor/Super Duty owners seem to have satisfactory results.


Why, when I first heard the term "tire balancing beads" I remembered when cleaning up a 1920's residential garage finding a dusty old package of something called "ENGINE REBUILD PELLETS".

:ROFLMAO:

...which upon reflection at the time I assumed were "Ringer [engine] Restore" but in solid form that one would drop a few into the bad engine's oil supply where they'd dissolve and then fill in cylinder wall scratches or whatever.
Centrifugal force. 🤷🤣🤣
I feel like I understand how they work one second and then a second later I think it's snake oil.
I have them in my super swampers on my bronco but they came with it and I don't notice anything "out of balance" unless I leave it parked on the driveway for extended periods. But, that I chalk up to "flat spots" from not moving.🤣
 
Balance beads work great. It's a dynamic balance similar to using something like the Centramatic or Balance Masters that go between the hub and wheel.


A lot of off-road guys around here do the poor-man's dynamic balance with airsoft BBs in their tires. They pop the tire bead on one side or put them in though the valve stem.

I run the Centramatics. One of my wheels currently has no weight on it. Tire shop didn't follow directions and use low-pro weights, so they got ripped off by the caliper at some point. I haven't had time to take it back in yet, but there is zero wobble at any speed and there are at least 3-4oz of weights missing on that one.

Short of a wheel/tire being pretty far out of balance, you could probably get away with running only the dynamic balancers or beads.
 
I only mentioned it and had never seen them until my daughter had them installed in her 38s on her jeep. I was helping her put the wheels on and said they forgot to add the wheel weights when they mounted the tires. She laughed at me and said they use beads now. I thought she was full of shit.
 
Just had my second oil change done today. First one was at 1000 miles. This one was at 2500 and the next will be at 5,000. After that, every 5K. The first two were free. Thinking about doing the rest on my own and installing an oil valve and using the vac trick!
Installing the valve with the shop vac trick was easy peasy. Oil changes are so easy now. I will be picking up one of these for my next oil change.
Most likely will be following the same OCI as you listed.
 
I upgraded the factory batteries, which were a little explodey, to the Battries Plus X2 AGM batteries. I feel like the truck is working much better, might be my imagination though. My wolfboxx timelapse seems to be working better too. I was pretty surprised they upped the warranty to 5 years.
 
I upgraded the factory batteries, which were a little explodey, to the Battries Plus X2 AGM batteries. I feel like the truck is working much better, might be my imagination though. My wolfboxx timelapse seems to be working better too. I was pretty surprised they upped the warranty to 5 years.
That and the Odyssey are the BEST batteries you can put in your truck hands down! Both the X2 and Odyssey are made in the same factory. Worth the extra $$$ IMPO.
 
Just ordered this today and looking forward to putting it on. Found it for an awesome price so pulled the trigger versus going with the Borla S-Type system which is the same but replaced the front resonator. There is a $200 discount code and used some points. Paid $777 with free shipping to my dealer. Picking it up this weekend and then have to find time to install it or pay a shop to do it.

IMG_7874.webp
 
Change my mind.

I just cain't wrap my head around how that becomes a permanent solution. How are they applied or installed? How do they find the sweet spot? How do they STAY PUT.

It seems I may be missing certain factoidials, because some Tremor/Super Duty owners seem to have satisfactory results.


Why, when I first heard the term "tire balancing beads" I remembered when cleaning up a 1920's residential garage finding a dusty old package of something called "ENGINE REBUILD PELLETS".

:ROFLMAO:

...which upon reflection at the time I assumed were "Ringer [engine] Restore" but in solid form that one would drop a few into the bad engine's oil supply where they'd dissolve and then fill in cylinder wall scratches or whatever.
I ve used them in trailer tires for a long time. They go in through the valve stem. They are very tiny ceramic (I think) beads. Or, what I used to do, is throw a pack in the tire before mounting.
The big trailer has traditional weights because I can’t muscle on a G rated trailer tire on a wheel. 😂
 
That Ford/Borla system robs you of torque... for nearly the same price as the full S-Type.

This is why, right here:

IMG_7601.webp


^ ^ ^ Dirthead Shed Dave Chappelle removed this from his 2020 Godzilla F350 DRW then cut it open for us to reveal a giant exhaust air brake. It's quiet! though.



For another $100, you can get the full Borla S-Type that gives us this critical Y-collector, and roughly 15 lb/ft more torque to the rear wheels.

IMG_7602.webp
 
That Ford/Borla system robs you of torque... for nearly the same price as the full S-Type.

This is why, right here:

View attachment 264910

^ ^ ^ Dirthead Shed Dave Chappelle removed this from his 2020 Godzilla F350 DRW then cut it open for us to reveal a giant exhaust air brake. It's quiet! though.



For another $100, you can get the full Borla S-Type that gives us this critical Y-collector, and roughly 15 lb/ft more torque to the rear wheels.

View attachment 264912
Do we have a forum vendor for Borla or do you just order direct?
 
That Ford/Borla system robs you of torque... for nearly the same price as the full S-Type.

For another $100, you can get the full Borla S-Type that gives us this critical Y-collector, and roughly 15 lb/ft more torque to the rear wheels.
If I wasn't able to get the Ford Performance Borla kit for under $800, and the Borla S-Type Cat Back was only $100-$200 more, I would have certainly gone with the Borla S-Type. Anyone that pays over $1500 for the Ford kit should have their head examined IMPO knowing the Borla S-Type kit is just a tad bit more. However, with that being said, my motivation is not an extra 15#/ft. as you'll never feel that in a truck like this and not something I personally care about. It is primarily for the exhaust note and to hear the engine make some noise. I saved over $900 buying this with the current Ford Performance promotion (ends September 15) and points from my Ford Visa Card. For a $900 savings, I'm sure most all of you would agree that this is a hell of a deal with little implications. Just my thoughts and rationale my friends :) Once I get it installed, I'll share pics. Others that have gone this route were extremely pleased with the sound and results so that was nice to hear as well.
 
Back
Top Bottom