🛠️ What did you do to your Tremor today? [2026 edition]

Happy to report, followed your instructions to the letter and no codes. You were spot on about my 7.3L not having a TCM relearn option.

Even adjusted the TPMS while I was in there.

Thanks so much! Love this forum.
Awesome! Glad everything worked out, my friend. If you need anything else, don't hesitate to ask.

Autobots, roll out!
 
So had a sill plate that wasn’t staying clipped. Tried to order a new platinum one but was told they are on national back order. Well while searching I came across a link on Fordtremor about these Ford Performance one so ordered up a set. Thanks @jrfuller for posting the info.
IMG_1768.webp
IMG_1767.webp
 
@Optimus🤖 procedure is correct for us semi-lterate former Army helicopter pilots found this on YouTube
Used this to update my 2024 going to 37's speedo/GPS have 1 mph difference around town and read the same at highway speeds.

Youtube video
on how to clear the DTC code that @Optimus🤖 's procedure is referring to
Ok, I'm going to have to try this again when the weather cools as it didn't work for me initially. Would be nice to have the speedometer accurate.
 
Installed @OmahaBravo LightGurad Lite today - excellent service and great kit

The fit from bit to fastener is very tight and precise, mucht tigher than any torx which is a good thing. I mention this, as I found putting fastner, washer on the bit, then using bit make fasterner finger tight, then tighten using a bit driver.

Do not over tighten, remeber the fastners are going into plastic. Over tightening fastner, risk is stripping out the plastic which almost guarantees the purchase of another tail light 🤪

1784401296677.webp
 
Installed @OmahaBravo LightGurad Lite today - excellent service and great kit

The fit from bit to fastener is very tight and precise, mucht tigher than any torx which is a good thing. I mention this, as I found putting fastner, washer on the bit, then using bit make fasterner finger tight, then tighten using a bit driver.

Do not over tighten, remeber the fastners are going into plastic. Over tightening fastner, risk is stripping out the plastic which almost guarantees the purchase of another tail light 🤪

View attachment 262719
Welcome to the finger-tightner-stripper-drive her-club!
 
IMG_3211.webp

Unless someone wants to donate to the Veterans community here in Texas … you know … me, I installed the new N3 dual steering stabilizers from rough country.

Now I need to go to someone to get the old stabilizer off as I cannot get the bolt out. You can see it zip tied back there.
 
Adjusted my tires to 50F and 46R cold after upgrading to 37s and learning how to use forscan.

I am shocked how well the truck rides now. My wife even commented how good it was in this morning toddler errands.
 
Adjusted my tires to 50F and 46R cold after upgrading to 37s and learning how to use forscan.

I am shocked how well the truck rides now. My wife even commented how good it was in this morning toddler errands.
Why stop there, I run mine at 45F / 40R
 
I run my stock Duratacs with a little bit of weight (200 lbs if that) in the bed of my 7.3 gasser at 40/40 cold.
 
I assumed physicist
There was a thread on ARFCOM a few years ago when MrHiggs offered his take on the subject. Someone then questioned his input and as it turned out, MrHiggs was on the team that discovered the Higgs Bosun particle. It was a legendary burn.
 
I run 43 psi front and 40 psi rear (300 / 275 kpa) running 37" Toyo ATIIIs

*Edited to include tire info per @McE ... Good call out!
 
Last edited:
I think you need to add 2 psi in the front and 3 psi in the rear so your front and rear psi totals to 69
Ok fine. But if I pump the rear that hard at 69, I'm making zero promises about not leaving skid marks.
 
There was a thread on ARFCOM a few years ago when MrHiggs offered his take on the subject. Someone then questioned his input and as it turned out, MrHiggs was on the team that discovered the Higgs Bosun particle. It was a legendary burn.

1000016434.gif
 
Back
Top Bottom