🛠️ What did you do to your Tremor today? [2026 edition]

This thread is active so I figure I’ll ask here lol. Stock 2026 Trm F350 tires and wheels…. Placard says 60/75. How low could I go on pavement before damaging the side walls? I’m at 60 all the way around right now because I ran out of time while pumping gas lol. I feel like lowering the rear that much has made a difference but I don’t know if it’s just in my head since I’m not that perceptive.

ETA: I guess I’d like to hear thoughts on impact to gas mileage as well since that is a concern in these things lol
 
This thread is active so I figure I’ll ask here lol. Stock 2026 Trm F350 tires and wheels…. Placard says 60/75. How low could I go on pavement before damaging the side walls? I’m at 60 all the way around right now because I ran out of time while pumping gas lol. I feel like lowering the rear that much has made a difference but I don’t know if it’s just in my head since I’m not that perceptive.

ETA: I guess I’d like to hear thoughts on impact to gas mileage as well since that is a concern in these things lol
Some of these guys are running 40-45 with forscan modifications. I run 55/60 and higher when towing. Stay lower if you don't have weight because I wore out the center of mine running 65/70-5 and I have always had weight in mine.
 
Some of these guys are running 40-45 with forscan modifications. I run 55/60 and higher when towing. Stay lower if you don't have weight because I wore out the center of mine running 65/70-5 and I have always had weight in mine.
not to be pedantic, but how much weight would you say makes a difference? I mean, I probably have 200 pounds in the toolbox and I’m a big guy so maybe 700 total of stuff in the cab in bed for most days.

also, I know as far as payload goes, 700 pounds just tickles this truck. But thinking of tire where I wonder if the number might be lower.

And I am editing to add that I forgot to say thank you lol! So, thank you all as usual.
 
Some of these guys are running 40-45 with forscan modifications. I run 55/60 and higher when towing. Stay lower if you don't have weight because I wore out the center of mine running 65/70-5 and I have always had weight in mine.
40 x 4 with stock Tremor Wranglers and wheels. 55 x 4 with the 14' flatbed. 70R/75F with the16K + 5th wheel.
In my climate, the tires heat up +5 PSI before I'm a mile down the road.
 
40 x 4 with stock Tremor Wranglers and wheels. 55 x 4 with the 14' flatbed. 70R/75F with the16K + 5th wheel.
In my climate, the tires heat up +5 PSI before I'm a mile down the road.
Same Climate so thank you.
 
F250/stock size tires (Falken AT4) and I run 55psi x4 most of the year but right now 50psi x4 because they heat up really fast (it's 106 degrees today). I haven't really noticed any fuel mileage difference than running at "recommended" pressures. If there is a difference, it is miniscule and outweighed by the greater comfort. Obviously, when towing I adjust depending on weight.
 
not to be pedantic, but how much weight would you say makes a difference? I mean, I probably have 200 pounds in the toolbox and I’m a big guy so maybe 700 total of stuff in the cab in bed for most days.

also, I know as far as payload goes, 700 pounds just tickles this truck. But thinking of tire where I wonder if the number might be lower.

And I am editing to add that I forgot to say thank you lol! So, thank you all as usual.
I have not weighed mine but....
Cxhd cap with aluminum skeleton, I think it's around #300
Decked drawers I think start at 200-250 with probably 4-500 lbs tools etc.
5-600 lbs at most under the cap at any given moment.
2-3 ladders on top
1-10 ten foot ground rods at any given moment
 
45 psi all the way around here but empty with a diesel. Basically, empty other than a few hundred pounds of tools. I actually plan to run 40 psi on the rear but I haven't adjusted my Stauns. On my Ram I ran 35 psi with 37"s/35"s but it was a bit lighter being a gasser. Towing I kick the tires up to placard listing. Honestly that was one of my reasons in getting a Ford; the 2025+ RAM TPMS hasn't been hacked (not even AEV can get it adjusted.) In my '16 Ram before AEV would sell the standalone ProCal, I just drove with the TPMS light on. Once I was able to adjust it, it became a really great tool.
 
I have not weighed mine but....
Cxhd cap with aluminum skeleton, I think it's around #300
Decked drawers I think start at 200-250 with probably 4-500 lbs tools etc.
5-600 lbs at most under the cap at any given moment.
2-3 ladders on top
1-10 ten foot ground rods at any given moment
Thank you! That gives me a good picture!
 
45 psi all the way around here but empty with a diesel. Basically, empty other than a few hundred pounds of tools. I actually plan to run 40 psi on the rear but I haven't adjusted my Stauns. On my Ram I ran 35 psi with 37"s/35"s but it was a bit lighter being a gasser. Towing I kick the tires up to placard listing. Honestly that was one of my reasons in getting a Ford; the 2025+ RAM TPMS hasn't been hacked (not even AEV can get it adjusted.) In my '16 Ram before AEV would sell the standalone ProCal, I just drove with the TPMS light on. Once I was able to adjust it, it became a really great tool.
Good thought- i forgot about weight difference since mine is Gas.
 
Got started on my VHF install after having various parts sitting for awhile now. Installed the BuiltRight panel behind the rear seat, used @NEOHIO cable to bring power back to the unit. Ran an Ethernet and USB-C cable back there too in prep for when I eventually get a Midland too.

Not fully done, but got it functional. Need to finalize how I’m gonna mount it in the console, and install the plug ends for the Ethernet and USB-C somewhere.

1/4 wave antenna up on the Swarfworks mount.

IMG_1581.webp
IMG_1582.webp
IMG_1583.webp
IMG_1585.webp
IMG_1584.webp
 
Got started on my VHF install after having various parts sitting for awhile now. Installed the BuiltRight panel behind the rear seat, used @NEOHIO cable to bring power back to the unit. Ran an Ethernet and USB-C cable back there too in prep for when I eventually get a Midland too.

Not fully done, but got it functional. Need to finalize how I’m gonna mount it in the console, and install the plug ends for the Ethernet and USB-C somewhere.

1/4 wave antenna up on the Swarfworks mount.

View attachment 263062View attachment 263063View attachment 263064View attachment 263065View attachment 263066
Did you find whoever tried to take a bite out of your radio?
 
Last edited:
Did you find whoever tried to take a bite out of your radio?

eBay special. So I expected a few bites. Looks like I might have some troubleshooting to do though. Ignition Sense is acting weird and not sure if I’m transmitting yet. 😂
 
  • Sad
Reactions: McE
This thread is active so I figure I’ll ask here lol. Stock 2026 Trm F350 tires and wheels…. Placard says 60/75. How low could I go on pavement before damaging the side walls? I’m at 60 all the way around right now because I ran out of time while pumping gas lol. I feel like lowering the rear that much has made a difference but I don’t know if it’s just in my head since I’m not that perceptive.

ETA: I guess I’d like to hear thoughts on impact to gas mileage as well since that is a concern in these things lol
The chart below is the first one I found for the OEM tires.
If you have the diesel, front axle weight is somewhere in the 4500lb range. Rear is 3500ish. You could run as low as 40 all the way around if you wanted. The huge drawback is going to be the handling. Or lack thereof.
1784676015400.webp
 
The chart below is the first one I found for the OEM tires.
If you have the diesel, front axle weight is somewhere in the 4500lb range. Rear is 3500ish. You could run as low as 40 all the way around if you wanted. The huge drawback is going to be the handling. Or lack thereof.
View attachment 263073
Thanks! it’s the 7.3 but this all gives me a good place to start!

I dropped them all to 55 for tomorrow and until I have time to dive into Forscan
 
This thread is active so I figure I’ll ask here lol. Stock 2026 Trm F350 tires and wheels…. Placard says 60/75. How low could I go on pavement before damaging the side walls? I’m at 60 all the way around right now because I ran out of time while pumping gas lol. I feel like lowering the rear that much has made a difference but I don’t know if it’s just in my head since I’m not that perceptive.

ETA: I guess I’d like to hear thoughts on impact to gas mileage as well since that is a concern in these things lol
2020gas
they recommend 60psi in front, 80psi in the rear.

that's for max load or max towing.

even the gassers are less weight in the rear with no loads so 60 psi all-around is a no brainer.

i run 50psi all around even with full overland gear. truck runs right at 9500 with full kit and me. I've gone as low as 10psi on trails & salt (Bonneville salt flats). if i know I'm bouncing trail to road to trail I'll run 25psi and leave it until I'm back to pavement for good.

several different tires, no issues that lowering the pressure has caused so far.

I'd say, if the streering feels more sloppy than you're comfortable with then too low. if the ride is too firm you're to high.

find your comfort zone & there you go.

worst case scenario you mess up & ruin your tires sooner than expected.

just get new tires
🤣😂🤣😂🤣

who doesn't look forward to a new set of tires
 
Using my new “Super Duty” Sun screen today. With my 31k points, I got that, a fender guard and a ground mat for working on it and the travel trailer.
IMG_4037.webp
 
Last edited:
Back
Top Bottom