🛠️ What did you do to your Tremor today? [2026 edition]

IMG_7078.webp

It’s not done yet but here a sneak peek, Carli level on 38/11.5r18s
 
If a CCLB is a Tremooore, this must be a Trmr.
@Ranger97 I think you should have a "TREVOR" sticker made for this. Why you may ask? "V" is just a little shorter version of "M". Some may say the middle portion is the best, anyway, so it's a compliment really.

Love the truck progress!! 🤜
 
Beautification and Moab prep:
Morimoto tail lights installed thanks @Nick@ApolloOff-Road once again great customer service.
Installation is fairly straight forward, recommend downloading and printing the instructions. It's a PITA trying read them on cell or tablet.

Installation tips:
  • Morimoto taillight Radar Bracket have very tight fit due to water gasket seal. Recommned using a gasket scrapper or trim removal tool, braking the seal safely removing the Radar Bracket
  • BLIS radar module installation - modules are oreiented differently on driver and passenger side. Morimoto has a diagram of correct positioning, double check for correct module oreientation.
  • Reistors are packaged magnet to magnet, these magnets are very strong use care when separating the resistors from each other to not damage wiring.
Morimoto radar bracket removal
View attachment 262612
Install complete - happy day BLIS also works
View attachment 262613

Moab prep as rear departure angle can be a concern - added 41.22 hitch slider https://41twentytwo.com/product/hitch-slider/ recommend using Ford OEM hitch reducer adaptor, part# HC3Z19H282A. Ford's hitch adapter is flared, lining up reciever and adapter hitch pin holes.

View attachment 262614
Glad you're happy with them, man! Thank you again for your support!
 
Some VHF work and testing today. Figured out my ignition sense issue (it’s always settings) so now my Upfitter turns the radio on and off while it maintains the constant power connection.

Swapped the existing connection off the radio to a quick disconnect as well.

My Tx issues was mic related, the shielding was crumbling with age, and some of the internal wires were frayed, so I suspect a short when the mic was moved around. So a new mic and all good.

Did some antenna testing to ensure the antenna and cabling was all good - especially since I was using a 1/4 wave Ground Plane antenna on the SW mount - should really have been a non, but I didn’t want the crazy length. 1.1-1.25 SWR, and 25-35W of power, so happy there.

Now I just need to find the time and where to mount it on the console. Wife isn’t a fan of moving it off the passenger seat whenever we go somewhere. 😂
 
Some VHF work and testing today. Figured out my ignition sense issue (it’s always settings) so now my Upfitter turns the radio on and off while it maintains the constant power connection.

Swapped the existing connection off the radio to a quick disconnect as well.

My Tx issues was mic related, the shielding was crumbling with age, and some of the internal wires were frayed, so I suspect a short when the mic was moved around. So a new mic and all good.

Did some antenna testing to ensure the antenna and cabling was all good - especially since I was using a 1/4 wave Ground Plane antenna on the SW mount - should really have been a non, but I didn’t want the crazy length. 1.1-1.25 SWR, and 25-35W of power, so happy there.

Now I just need to find the time and where to mount it on the console. Wife isn’t a fan of moving it off the passenger seat whenever we go somewhere. 😂
I am working on this mentally right now. I have an old Icom 65W 2m I may mount in the console although I have thought about getting something new or mounting both my 50w GMRS (Wouxun) and the icom. I am all about reliability and simplicity so I use FT-60R as my EDC HT. Lol. No need really for digital around here. Im not in to HF yet thought Ive considered getting my General.

The key will be running the antenna (fender mount I guess? I have 1/4 and 1/2 plane 2m as well as 70cm/ GMRS antennas- I have spent a lot at Signal Stuff lol) and what to ground where. Man if you want to start a debate among ham nerds, talk grounding in a Mobile set up lol. Have you posted elsewhere about your Comms setup and choices?
 
Just what I’ve posted in this mostly; I’ve definitely put way too much mental thought into this too…

I have the Swarfworks dual NMO and Starlink mount, replacing my 3rd Brake Light, so my antennas come right inside there, and are just fed down to behind the rear passenger seat. For a fender mount, I’d assume if you don’t go through the firewall, you’re looking at some of the rubber grommets in the floor. There’s one under the passenger footwell carpet, and another in the rear passenger corner that’s used for the sunroof drain - you might have it if you don’t have a sunroof.

I was hoping to avoid adding extra holes in the cab, so that’s where the NEOHIO cable comes in. (I know I’ll potentially get yelled at for not being direct to battery, but it’s working.) Plugs in behind the glovebox to the ProUpfit connection. Gives you 2x 50A (2x 25A lines per that can be linked for 50A each) grounded runs. Put that down through the passenger cable channel with a single line off an upfitter to fake an ignition sense line - switch on, radio thinks truck is on, switch off, happy wife without random radio chirps.

Radio itself is a Kenwood TK-7180 with remote head unit, as I really only need VHF up here for the resource roads I travel on for work. Took a chance on a couple of eBay sales and saved myself a bundle versus new. Just needed to get the antenna, and then as of last night, a new mic.

Since I have to two lines for power, and the two NMO lines, I’m hoping to eventually add a GRMS - Midland 50W, so I ran an Ethernet line and a USB-C through the headliner so I could mount the body of the Midland back with the Kenwood, and use the run cables as a mic port and extra USB-C (as the one on the unit is always powered, so it’ll give another charging port).

Ran the remote head cable up in the passenger footwell too - I’m rapidly running out of room there. Right now, it’s poking out below the glovebox so I could get it tested, and functional because I’ll be using it this weekend.

For a mic mount, I repurposed my ProClip mount up by the radio. Part of me is regretting loosing the MagSafe mount there and having my phone right there, but getting back into the habit of plugging it in will likely be better as it’ll free up WiFi for my Starlink.

As for mounting it in//on the console, I’ve currently got two plans of attack. And not sure which one I want to follow through with. It’ll likely depend on what I find when I pull the console back to work on it.

My original thought was that I replace the front cubby under the slider (where the USBs and wireless charger is) with the non-wireless one, which will give me enough room to hide the radio itself with a flush mount bracket, as well as a USB-C and Ethernet plug for the eventual GRMS.

From talking to folks here, and watching some videos, I was too sure if I’d have the space for the whole radio, hence the good eBay deals on the remote head unit.

Doing this obviously kills the wireless charging in my truck, but I still rock a iPhone Mini, so my phone is too small to use it anyhow. And then the radios are fully hidden unless in use. So I have the non wireless cubby here and ready to go.

But, my Mini is showing its age, and is starting to struggle hard, so with a potential phone change here where the wireless will come in handy for more than just my wife’s phone, I’m starting to consider putting the USB-C port in the wireless charger cubby to add a future power point there, and then mounting the Ethernet and Kenwood head in the drivers pocket, facing up.

I figure the final mounting won’t happen until next days off, so I’ll have time to put even more thought into that before it happens.

The guy that did my testing for me was impressed with the values I got all things considered, so maybe I helped change some minds. The same concerns were raised - not direct to battery for ground, 1/4 wave antenna with no grounding plane, etc. 😆

I am partially considering if I want to try out the COMPACtenna, and get that 1/4 wave height down to 9”, but not sure if the juice is worth the squeeze there.


I’m no HAM or radio expert at all, and even I question some of the points on the website, but the website screams evil genius who figured this shit out before anyone else and I feel I can trust it to work as claimed…
 
Just what I’ve posted in this mostly; I’ve definitely put way too much mental thought into this too…

I have the Swarfworks dual NMO and Starlink mount, replacing my 3rd Brake Light, so my antennas come right inside there, and are just fed down to behind the rear passenger seat. For a fender mount, I’d assume if you don’t go through the firewall, you’re looking at some of the rubber grommets in the floor. There’s one under the passenger footwell carpet, and another in the rear passenger corner that’s used for the sunroof drain - you might have it if you don’t have a sunroof.

I was hoping to avoid adding extra holes in the cab, so that’s where the NEOHIO cable comes in. (I know I’ll potentially get yelled at for not being direct to battery, but it’s working.) Plugs in behind the glovebox to the ProUpfit connection. Gives you 2x 50A (2x 25A lines per that can be linked for 50A each) grounded runs. Put that down through the passenger cable channel with a single line off an upfitter to fake an ignition sense line - switch on, radio thinks truck is on, switch off, happy wife without random radio chirps.

Radio itself is a Kenwood TK-7180 with remote head unit, as I really only need VHF up here for the resource roads I travel on for work. Took a chance on a couple of eBay sales and saved myself a bundle versus new. Just needed to get the antenna, and then as of last night, a new mic.

Since I have to two lines for power, and the two NMO lines, I’m hoping to eventually add a GRMS - Midland 50W, so I ran an Ethernet line and a USB-C through the headliner so I could mount the body of the Midland back with the Kenwood, and use the run cables as a mic port and extra USB-C (as the one on the unit is always powered, so it’ll give another charging port).

Ran the remote head cable up in the passenger footwell too - I’m rapidly running out of room there. Right now, it’s poking out below the glovebox so I could get it tested, and functional because I’ll be using it this weekend.

For a mic mount, I repurposed my ProClip mount up by the radio. Part of me is regretting loosing the MagSafe mount there and having my phone right there, but getting back into the habit of plugging it in will likely be better as it’ll free up WiFi for my Starlink.

As for mounting it in//on the console, I’ve currently got two plans of attack. And not sure which one I want to follow through with. It’ll likely depend on what I find when I pull the console back to work on it.

My original thought was that I replace the front cubby under the slider (where the USBs and wireless charger is) with the non-wireless one, which will give me enough room to hide the radio itself with a flush mount bracket, as well as a USB-C and Ethernet plug for the eventual GRMS.

From talking to folks here, and watching some videos, I was too sure if I’d have the space for the whole radio, hence the good eBay deals on the remote head unit.

Doing this obviously kills the wireless charging in my truck, but I still rock a iPhone Mini, so my phone is too small to use it anyhow. And then the radios are fully hidden unless in use. So I have the non wireless cubby here and ready to go.

But, my Mini is showing its age, and is starting to struggle hard, so with a potential phone change here where the wireless will come in handy for more than just my wife’s phone, I’m starting to consider putting the USB-C port in the wireless charger cubby to add a future power point there, and then mounting the Ethernet and Kenwood head in the drivers pocket, facing up.

I figure the final mounting won’t happen until next days off, so I’ll have time to put even more thought into that before it happens.

The guy that did my testing for me was impressed with the values I got all things considered, so maybe I helped change some minds. The same concerns were raised - not direct to battery for ground, 1/4 wave antenna with no grounding plane, etc. 😆

I am partially considering if I want to try out the COMPACtenna, and get that 1/4 wave height down to 9”, but not sure if the juice is worth the squeeze there.


I’m no HAM or radio expert at all, and even I question some of the points on the website, but the website screams evil genius who figured this shit out before anyone else and I feel I can trust it to work as claimed…
Thanks! Lots to think about. I am trying to use what I have for now. Got some rough paychecks ahead (not super seasonal but early fall is my slow time.). So I am thinking $30 for some fender mount and I can run cables through whichever side I mount the radio. Maybe that little Driver side center console cubby down by my calf. I need to "Dry Fit" what I have and go from there but it's SO HOT. Forscan first now that I have weighed the truck and know what pressure to run my tires at lol.
 
Summoned again by @Battle Born Offroad. The brand new Morimoto XRBG EVO LED headlights are installed and ready to brighten people's night 🤪.


23391.webp

23392.webp


These things are awesome. I love the start-up sequence as well as the RGB feature. The illegal superchargers are also installed. I get flashed enough as it is but these will take it to a whole notha level!

23399.webp

23417.webp


Chas doing the video shoot.



23403.webp

23424.webp
23431.webp

23432.webp


I want to thank Morimoto for reaching out to @Battle Born Offroad. Chas and his crew needed a truck and voila! My baby got new flashers.

Thank you brothers for making this happen. Video content coming soon 👊.

23438.webp
23439.webp
 
Last edited:
LOVE how visible it is in the daytime. Just looks great. I will envy from afar because no way I can spend the money ya'll do on lighting lol. Maybe get some amber fogs but that's the extent of it lol
 
EDITED: Too much thinking and asking here by me. Basically- use the load chart for your tires with the CAT Scale weights to figure your tire pressures but 3 paragraphs of me thinking out loud is too much.
 
Last edited:
Too bad this will only work on a 2.5" hitch.

I have a 3" receiver and it would require two reducers. That will prevent the slider from seating all the way in.

No one seems to make a 2.5" or 3" hitch slider.
A recovery mount works about as well and provides a better recovery point if needed. I have this in 2.5. Not sure they make 3 inch, but at least then only one reducer https://a.co/d/04oymI76
 
A recovery mount works about as well and provides a better recovery point if needed. I have this in 2.5. Not sure they make 3 inch, but at least then only one reducer https://a.co/d/04oymI76
Yeah I was actually considering throwing a Harbor Freight hitch in there with the tow ball facing down. Who cares if it gets all scraped up? I can drag that thing across rocks and it will hold up just fine. Exact same principle as the "slider" only it is much much cheaper.


This and a reducer/adapter and you are in business for a fraction of the cost.


Or this with the ball mounted upside down


Pretty sure I will be sporting one of these options in Moab.
 
Last edited:
Back
Top Bottom