šŸ› ļø What did you do to your Tremor today? [2026 edition]

So while I wait for the security hard for A pillar lights to show up, didn’t think that thru. Thought I’d started prepping the next project BMC fog light kit with BD lights. And don’t forget the anti seize on the hardware, or so I’ve been told.View attachment 252521
View attachment 252517View attachment 252519View attachment 252520

Yes, always use anti seize on stainless steel hardware, and don’t torque them down with an impact gun. Do the final torque/tightening with a ratchet or wrench.
 
Where did you put the antenna for the gmrs
Great question. I toyed with several spots; on the headache bar, on the existing FM antenna with an extension tube, and somewhere I could easily remove it and stow it, all the time thinking of interference in the TxRx scenarios. So, my first experimental spot, is on the dash with the Built Right dash panel, with an aftermarket mount I got on Amazon. (With 3/4-inch hole for the aftermarket "short" cable I bought.) The original 20' cable was too long for this spot and length equals loss in a cable. The clear view forward (and somewhat backwards) would be the same essentially as putting it outside at the FM antenna.

The reception seems very good for this spot, though I don't have another TxRx radio to test it. I receive the weather station in Nevada County, a good 20+ miles away. I also pick up gibberish from the freeway on the other side of the hill from me.

All mounting locations have advantages/disadvantages. The best spot would be on the headache bar but running a cable where I could still open the covers of the Diamond Back cover without damaging the cables was too involved, plus I would have had to get a 25' cable which would equate to more loss in the cable.

Mounting on the FM antenna was also involved, no easy way to run the cable through the firewall. Plus, most likely no better reception than where it is on the dash.

The dash position is OK, but the antenna sticks up and does get about 2" in the view over the hood. But it's off to the side and doesn't bother me. If it ever does, I may extend it to the passenger side by creating some sort of mount. It can easily be removed when not in use and I have a protective cap to terminate it when not in use. I powered it from the upfitter switch that powers my dash accessories. I have an LED that flashes (seen in the upfitter view) that reminds me to turn it off before leaving the truck. It only flashes (and sounds a beep alarm for 3 seconds) if the ignition is shut off and the upfitter is still on.

In addition to the antenna, I set the microphone to have audio come out of it instead of the built-in speaker. (I planned on using an external speaker, but the mic sounds just fine to me. There are other options for sound on this radio as well.) I also used a right-angle LAN connection so I can close the cubby while in use. (Amazon) I built a mic holder from a piece of polycarbonate plastic I had laying around, held in with a small piece of double-sided 3M tape.
 

Attachments

  • 20260405_212434.webp
    20260405_212434.webp
    134.2 KB · Views: 44
  • 20260405_174837.webp
    20260405_174837.webp
    180.7 KB · Views: 45
  • 20260406_171438.webp
    20260406_171438.webp
    184.2 KB · Views: 44
  • 20260406_171352.webp
    20260406_171352.webp
    213.6 KB · Views: 48
  • 20260406_172154.webp
    20260406_172154.webp
    208.2 KB · Views: 46
  • 20260406_172848.webp
    20260406_172848.webp
    206.2 KB · Views: 46
I know most already have their of material suppliers/companies. I've been long waiting for this to come back into supply. I like the simplicity of the setup not to mention the pricing. I'll have to figure out a setup/demo location for some added pics at some point.

 
I'll have to figure out a setup/demo location for some added pics at some point.


I was pondering something similar the other day, but doing it with HarborFreight merchandise.

Your tarp linked in your post is no doubt a quality product (and of greater quality than what we'd expect from HazardFraught), but HF does sell grommeted canvas tarps, in a nice hunter green color (that fade! soon enough in bright sun to a cheesy turquoise, but I digress) and in three sizes: 6' X 8', 8' X 10' and 10' X 12'.

I use their 6' X 8' already as a rear canopy for my little sleeper trailer:


...which (the point of this post) got me to thinking, why not grab a couple of their 10' X 12' along with a pickup bed contractor's rack to use to carry 3/4" EMT tubing (for assembling canvas sun shade frames) but mainly as a relatively inexpensive accessory structure on the truck to secure these tarp or tarps to.

When camping, one can never have enough shade or enough tables. Just have to be ready to furl 'em when the gale force winds kick up! and have plenty of stakes and line with which to secure them to ground.

I suppose this here chatter should to go into a camp rigging thread if there is one somewhere?
 
@Apples : I had long considered a "collective" of parts to do the same thing. In general it was more about the added versatility of the product line.

:cool: :cool: šŸ‡ŗšŸ‡² šŸ‡ŗšŸ‡² šŸ‡ŗšŸ‡² šŸ‡ŗšŸ‡²
 
That was my original plan. But after using Grok to do some product searching, I found that KC Hilites makes a wire hider using VHB tape so I can run it right on the edge of the windshield. $30 from Walmart. It arrives tomorrow so I’ll update with a pic when it’s installed.

Now I need to find this low rider Tremor…. 🤢
post 931 this thread

someone mentioned it might be an April fools joke

that'll probably be a TOTM theme soon

the way things are going on here lately
šŸ˜…šŸ¤£šŸ˜…šŸ˜‚šŸ¤£šŸ˜‚šŸ¤£šŸ˜‚šŸ¤£
 
Finally got around to installing S&B transfer pump and a Homelink rear view mirror that actually has some range.

Working on a skid plate to mount at the DEF tank mounting points to protect pump better.

Got the mirror from Bob's Automotive Mirrors.

https://www.bobsmirrors.com/NEW-Adv...50-F350-F450-F550-F600-Super-Duty_p_1785.html

View attachment 252693View attachment 252694View attachment 252695View attachment 252696
awesome
makin me feel better about how beat-up the underside of my truck is too.šŸ¤£šŸ˜‚šŸ¤£šŸ¤£

nice pump install toošŸ‘
 
awesome
makin me feel better about how beat-up the underside of my truck is too.šŸ¤£šŸ˜‚šŸ¤£šŸ¤£

nice pump install toošŸ‘
If I had a 2 post lift at home it would be clean as a whistle under there, unfortunately I do not so it stay dingy and beat up.
 
Finally got around to installing S&B transfer pump and a Homelink rear view mirror that actually has some range.

Working on a skid plate to mount at the DEF tank mounting points to protect pump better.

Got the mirror from Bob's Automotive Mirrors.

https://www.bobsmirrors.com/NEW-AdventGentex-Frameless-Auto-Dim-Rear-View-Mirror-wHomelinkĀ®-V5-HomelinkĀ®-Connect-Plug-Play-for-2017-2026-Ford-F250-F350-F450-F550-F600-Super-Duty_p_1785.html

View attachment 252693View attachment 252694View attachment 252695View attachment 252696
Did you install the transfer pump on an existing S&B tank?

Did you have to drop the tank to install the pump? I’ve been eyeing those but really dont want to drop the tank in the driveway.
 
Did you install the transfer pump on an existing S&B tank?

Did you have to drop the tank to install the pump? I’ve been eyeing those but really dont want to drop the tank in the driveway.
Yes you have to drop the tank, it's not a terrible job, can get it done in a couple hours if you have everything lined up and ready to go. or a day and a half if you have to go to the hardware store to fabricobble mounting solutions for the hose ends like I did.
 
my 25 should be all wrapped up with some new suspension and wheels/tires today.... Im excited to get rid of the Tremor Rake..
 
Installed my Oxford White and Darkened Bronze Metallic Tailgate AppliquƩ from BFN. I know they are pricey, but the quality is unmatched.
I was thinking they can’t be that bad, and then I looked. šŸ˜‚

God damn does it look good though. Very nice.
 
Back
Top Bottom