🛠️ What did you do to your Tremor today? [2026 edition]

Mounted my Midland radio in the cubby above the glove box. I'm ready for Moab now. 😁
Also changed my cabin filter with the K&N washable filter. The original didn't look all that bad after two years of use but since I was in there to mount the GMRS radio, I changed it.
20260404_210836.webp
 

Attachments

  • 20260404_145644.webp
    20260404_145644.webp
    270.3 KB · Views: 44
  • 20260404_145116.webp
    20260404_145116.webp
    213.5 KB · Views: 45
  • 20260404_153410.webp
    20260404_153410.webp
    137.2 KB · Views: 47
Just got my truck back from the shop. Ditched the innov8's and Carli for airbags and 26" wheels!
View attachment 251708
🤞🤞🤞🤞🤞🤞🤞🤞🤞
please please
🤣😅😅🤣🤣🤣

tell me you've got hydraulics & it's setup to pick it back up & slap the 38" with beadlocks on it too??????

hopin
🤞🤞🤞🤞🤞
please
🤞🤞🤞🤞🤞🤞

if so
really sweet!!!!!

if not
to each their own

perdy sweet ride
either way
 
Added the Baja designs S2 rear lights (trigger on Aux 1) and Warn rear winch 2 gauge wire harness (trigger on Aux 2.) Tested the winch wiring with my Vair 400P. I need to figure out something cleaner to connect the compressor. I have a Warn 6000 SDP that is actually fairly impressive for 6,000 lb winch you can carry with one hand. Draws some current with heavy pulls though.

View attachment 252097View attachment 252098View attachment 252099
i tuck my anderson in the hitch tube. so it's out of the way and protected.

just sharing
 
Grabbed the Front Runner rack on Black Friday but finally had nice enough weather to install. Got the Baja Designs likable lights installed but now I’m pausing for suggestions. For those who have lights on the roof, how did you run the wires down to under the hood? I only want to drill as a last resort.
View attachment 252199
if you can get the wiring needed minimized enough. go under the roof rack trip, down & under the rubber flap & under the rubber void filler (under the wippers) into the engine compartment. i babied the wire behind the antenna to help make sure it didn't get into the hood henge.
20260402_183650.webp
20260402_183656.webp
20260402_184139.webp


worked out pretty sweet for what I'm in the middle of.

I'll share when i finsh it all.

I'm being told it's ugly and looks alien.

😅🤣😅🤣😅🤣😅😅

if ol'boy can low rider a tremor and get likes & trophies. i can put lights where i need 'em!!!!
😅🤣😅🤣😅😅
 
if you can get the wiring needed minimized enough. go under the roof rack trip, down & under the rubber flap & under the rubber void filler (under the wippers) into the engine compartment. i babied the wire behind the antenna to help make sure it didn't get into the hood henge.View attachment 252337View attachment 252338View attachment 252339

worked out pretty sweet for what I'm in the middle of.

I'll share when i finsh it all.

I'm being told it's ugly and looks alien.

😅🤣😅🤣😅🤣😅😅

if ol'boy can low rider a tremor and get likes & trophies. i can put lights where i need 'em!!!!
😅🤣😅🤣😅😅
Can't wait to see 😃
 
Rainy afternoon. Good opportunity to change the oil. The PPE filter holds a lot more oil than the OEM filter. Almost 40 ounces to get it just below the threads

image.webp
 

Attachments

  • image.webp
    image.webp
    275.4 KB · Views: 9
Installed yaw sensor, TPMS sensor, and back-up camera on the toy hauler. Turns out, the trailer BLIS is only fifth wheels so didn't install that. Next up is to get 1k miles on the truck and then tow the trailer to Discount to get the TPMS installed in the tire.
Trailer wiring.webp
 
No photos but installed the Open Trail Creations upfitter kit, and wired up the Dirt Church Industries ARB compressor. Installed the compressor couple months ago but lagged on the wiring knowing I was gonna do the OTC. Also ran a line from upfitter #6 to the rear to replace the center pin on the 7 pin to avoid blowing the tow module.
 
I finally had a chance to take the truck out of the city and adjust all of the lights to their final positions. I got lucky and had a great sunset while I was waiting for it to get dark. There is no editing on either of the pics, it’s amazing how the red sunset makes the Carbonized Grey truck look bronze from one side. All lights are being controlled by the Switch Pros RCR 12.

Currently running all amber lenses, but I do have clear lenses if I decide to swap or mix them up.

XL 80’s and S1’s on the A pillars
Squadron Pro and Squadron SAE Fog Lights
XL Pro Linkable Light Bar
S2 pros in side step boxes
4 S2 Pros (on @legmar mount) and 2 Squadron Pros below the rear bumper

I wish I could mount/point the S2’s in the step pockets a little more level, if anyone has 3d printed a “wedge mount” for this please let me know. Edit - This has been solved, new mounts installed.

IMG_0198.webp

IMG_0197.webp

IMG_0185.webp
 
Last edited:
I Finally had a chance to take the truck out of the city and adjust all of the lights to their final positions. I got lucky and had a great sunset while I was waiting for it to get dark. There is no editing on either of the pics, it’s amazing how the red sunset makes the Carbonized Grey truck look bronze from one side. All lights are being controlled by the SwitchPros RCR 12.

Currently running all amber lenses, but I do have clear lenses if I decide to swap or mix them up.

XL 80’s and S1’s on the A pilars
Squadron Pro and Squadron SAE Fog Lights
XL Pro Linkable Light Bar
S2 pros in side step boxes
4 S2 Pros (on @legmar mount) and 2 Squadron Pros below the rear bumper

I wish I could mount/point the S2’s in the step pockets a little more level, if anyone has 3d printed a “wedge mount” for this please let me know.

View attachment 252447
View attachment 252448
View attachment 252449
Looks great! Stay with the amber. It's better at night in fog, dust, and easier on the eyes than white or light closer to the blue spectrum. (That's why "blue blocker" sunglasses were popular.)
 
I Finally had a chance to take the truck out of the city and adjust all of the lights to their final positions. I got lucky and had a great sunset while I was waiting for it to get dark. There is no editing on either of the pics, it’s amazing how the red sunset makes the Carbonized Grey truck look bronze from one side. All lights are being controlled by the SwitchPros RCR 12.

Currently running all amber lenses, but I do have clear lenses if I decide to swap or mix them up.

XL 80’s and S1’s on the A pilars
Squadron Pro and Squadron SAE Fog Lights
XL Pro Linkable Light Bar
S2 pros in side step boxes
4 S2 Pros (on @legmar mount) and 2 Squadron Pros below the rear bumper

I wish I could mount/point the S2’s in the step pockets a little more level, if anyone has 3d printed a “wedge mount” for this please let me know.

View attachment 252447
View attachment 252448
View attachment 252449
Looks great, brother! I agree with @Canyon Trekker: stay with Amber so you don't get blue blocker 🤪.
 
if you can get the wiring needed minimized enough. go under the roof rack trip, down & under the rubber flap & under the rubber void filler (under the wippers) into the engine compartment. i babied the wire behind the antenna to help make sure it didn't get into the hood henge.View attachment 252337View attachment 252338View attachment 252339

worked out pretty sweet for what I'm in the middle of.

I'll share when i finsh it all.

I'm being told it's ugly and looks alien.

😅🤣😅🤣😅🤣😅😅

if ol'boy can low rider a tremor and get likes & trophies. i can put lights where i need 'em!!!!
😅🤣😅🤣😅😅
That was my original plan. But after using Grok to do some product searching, I found that KC Hilites makes a wire hider using VHB tape so I can run it right on the edge of the windshield. $30 from Walmart. It arrives tomorrow so I’ll update with a pic when it’s installed.

Now I need to find this low rider Tremor…. 🤢
 
I Finally had a chance to take the truck out of the city and adjust all of the lights to their final positions. I got lucky and had a great sunset while I was waiting for it to get dark. There is no editing on either of the pics, it’s amazing how the red sunset makes the Carbonized Grey truck look bronze from one side. All lights are being controlled by the SwitchPros RCR 12.

Currently running all amber lenses, but I do have clear lenses if I decide to swap or mix them up.

XL 80’s and S1’s on the A pilars
Squadron Pro and Squadron SAE Fog Lights
XL Pro Linkable Light Bar
S2 pros in side step boxes
4 S2 Pros (on @legmar mount) and 2 Squadron Pros below the rear bumper

I wish I could mount/point the S2’s in the step pockets a little more level, if anyone has 3d printed a “wedge mount” for this please let me know.

View attachment 252447
View attachment 252448
View attachment 252449
Love it so much!!!! 😍🤩
 
Mounted my Midland radio in the cubby above the glove box. I'm ready for Moab now. 😁
Also changed my cabin filter with the K&N washable filter. The original didn't look all that bad after two years of use but since I was in there to mount the GMRS radio, I changed it.
View attachment 252322

Where did you put the antenna for the gmrs
 
So while I wait for the security hard for A pillar lights to show up, didn’t think that thru. Thought I’d started prepping the next project BMC fog light kit with BD lights. And don’t forget the anti seize on the hardware, or so I’ve been told.
IMG_1372.webp

IMG_1368.webp
IMG_1370.webp
IMG_1371.webp
 
Ordered the OTC uplifter and ground harness. Now I just need to decide what fog light solution to use.
 
Back
Top Bottom