I've been doing some thinking about my plans for Shadowfax's electrical and the upfitter switches. I've solidified many of them at this point, so I'm going to document what I have planned out so far.
Ignition only switches:
1. Front off-road lights
2. Reverse lights
3. Winch
4. TBD
Always hot switches:
5. Interior electronics (CB radio, Ham radio, commercial radio for SAR, inverter, etc)
6. Strobe/warning/emergency lights (fixed pattern)
Let's walk through this in a bit more detail. Of note, not all of these mods are purchased at this point, and may be a ways out before they are (thinking specifically of the lighting on switches 1 and 2 with this comment).
1. Front off-road lights are on switch 1 because I want them to be easily accessible while at speed. Being in the first position makes it easier to select them without looking at the switches. The front off-road lights will be a pair of white lights installed in the Baja Designs Dual Fog Pocket Kit. The other pair of lights will be amber and wired to the factory fog light button.
https://www.bajadesigns.com/products/Ford-Super-Duty-20-On-Dual-FPKs.asp
2. Reverse lights are in position 2 as they are likely to be frequently used, but it's OK if I need to look for them as I will inherently be going slowly and able to easily stop since they are intended for reversing. Reverse lights will be Baja Design S1's flush mounted in the rear bumper.
https://www.bajadesigns.com/pc_product_detail.asp?key=146B2591AB6442359BA9E11CE749777A
3. Winch is third just because. Of note, it's on an ignition only switch since I intend to only be using the winch with the engine running. Even if the engine won't fire, as long as I can turn the ignition on, the winch will work, so I still have that safety factor in a pinch.
4. This one is still to be decided, though I've narrowed it down to two options. Both only make sense with the truck running, so an ignition only switch is fine. Additionally, they are fine to be in the middle of the switch block from an accessibility standpoint. The two I'm deciding between are:
- Battery Charge Protection (BCP). This is a feature built-into the PCM that, when the truck is in park and a few other conditions are met, the PCM will adjust the RPM to maintain battery voltage based on the current load. Think of it as smart high idle: variable based on battery voltage. This could be useful when running the inverter and radios all at once. To read more about this, check out the 2022 Body Builders Layout Book, page 117: https://madocumentupload.marketinga...4f2a9dc16b11a696cd10141db8a36a8da090&v5=False
- 2WD Low. This is a feature brought up elsewhere on this forum, and originating from another forum, where you put a relay on the vacuum circuit for the front hubs. By disabling that circuit when in 4WD Low, you disengage the front hubs allowing you to use low range with only one axle engaged. This could be useful for low speed maneuvering, where you want the extra control from low range but want to retain the steering ability of 2WD: https://www.ford-trucks.com/forums/1546205-2lo-mod-2wd-low-auto-front-hub-override-mod.html
5. Interior electronics are on an always hot switch because I want to be able to use my radios without worrying about the ignition timing out or having the truck running. This could be while running a repeater or just monitoring for communications. It just makes sense to me to tie the inverter into that as well, and I definitely want the inverter on a switch because otherwise it would be permanently hot once I upgrade to the pure sine wave inverter (for that modification see this thread:
https://www.fordtremor.com/threads/replacing-factory-inverter-with-pure-sine-wave-inverter.7134/).
6. Strobe/warning/emergency lights are on 6. Given their purpose I absolutely want to be able to turn them on whenever I want, regardless of the truck's ignition state. Additionally, they are in position 6 for a similar reason to the off-road lights in position 1: easy, blind access.
For switch 5 I intend to add a fuse block that is powered by this switch (an idea mentioned by someone else here on the forum, unfortunately I don't remember who!). Between the battery and the fuse block, I will have a low voltage cut-off switch to protect the battery from running dead. I will also install a voltage gauge to allow me to monitor it and start the engine before the cut-off switch needs to kick in. The gauge will also be powered by the fuse block to ensure when the fuse block is turned off, the gauge is as well so it can't kill the battery.
I would love to be pointed to any battery gauges and/or cut-off switches you all can recommend or suggest.
