🛠️ What did you do to your Tremor today? [2026 edition]

Can you confirm or deny that a standard click type torque wrench is typically more accurate when in the middle of it's range? Such as 150 ft lbs for our lug nuts using a 10-150 scale wrench vs a 25-250 scale wrench? This is just what I remember reading in the past. I'm certainly no expert.

I typically install the nuts on the studs by hand for a few threads to ensure they are not cross treaded. Then, run the nuts down the threads using the impact on minimum trigger pull to seat them against the wheel. Then I use the torque wrench to start tightening them in the proper pattern to about half the torque value then again to the full torque value. I haven't had a wheel fall off or ever broken a stud.
See my post above.
 
Got to spend an hour at Canadian customs this morning while they went through every compartment, packout, bag and drawer in my truck
They saw from my passport that I am a CCW holder and asked if I own guns. Told me after the fact they had me pegged for having a gun in the truck- good thing I didn’t
From searching Reddit I guess my mistake was admitting to owning a gun- oh well I’m not in a rush and they were fairly pleasant. Gave me some good advice for places to check out while I’m heading towards the Dempster
where did you cross ?
 
Canada is terrible. I have been harassed so many times even when I was Nexxus (and I have a Canadian passport.) I was attending a class there (and I had Nexus) and they weren’t going to let me in because I might be teaching the class. I had to get after them and prove I was Canadian.

I recall my parents yelling at them in the eighties as it was always a cluster trying to cross the border with minivan full of hockey bags. The airports aren’t too bad but the land crossings are a joke. It’s Super Trooper to the max. Next time i’m saying meow.
 
Canada is terrible. I have been harassed so many times even when I was Nexxus (and I have a Canadian passport.) I was attending a class there (and I had Nexus) and they weren’t going to let me in because I might be teaching the class. I had to get after them and prove I was Canadian.

I recall my parents yelling at them in the eighties as it was always a cluster trying to cross the border with minivan full of hockey bags. The airports aren’t too bad but the land crossings are a joke. It’s Super Trooper to the max. Next time i’m saying meow.
While I was waiting on my all but strip search, there was another guy in there who was a dual citizen and border patrol was trying to accuse him of bringing commercial goods in undeclared because he was returning a transmission core for a piece of ag equipment so he could get his core charge refunded. All CBP wanted to hear was he was going to get $1500 and made him pay taxes on it
 
That was costly
It certainly was and shocker other driver was uninsured thank heaven we have unisured motorist coverage
 
Second oil + filter change! at 10,000 miles. Got this one done at 9800.0 before I do another 1000 mile round-tripper and then some. Did the second tire rotation two weeks ago.

[oil, filter, tire rotation every 5000 miles]
 
Removed the folding under-seat storage bin.

I've got two car seats, and they don't get used. When I did have the seats up, it was for the dogs, and it got in the way anyway. And lastly, the floor mats that came with the truck were actually for a truck that didn't have the storage bins anyway.

Super simple, though I didn't factor in that the long bed fuel tank would get in the way.

A couple of tips:
You don't need a T40 Torx unless someone else cranked the bolts down. Once I removed the nuts from above, I just grabbed a pair of vice grips, loosened the bolts, and backed them out as far as I could by hand from the top. I was able to easily feel them from the bottom and remove them.
When reinstalling the bolts from above, one of them is too long and will cause contact under the cab. For $2.50, I bought four M8-1.25x12mm bolts from the local hardware store and installed them from the top.
 
Been getting beaten to death on the Stewart-Cassiar highway so I asked Claude to give me settings for the fox dsc I have in front
So far it has made a significant improvement from having both adjusters set to full open

IMG_8368.webp
IMG_8369.webp
 
Can you confirm or deny that a standard click type torque wrench is typically more accurate when in the middle of it's range? Such as 150 ft lbs for our lug nuts using a 10-150 scale wrench vs a 25-250 scale wrench? This is just what I remember reading in the past. I'm certainly no expert.

I typically install the nuts on the studs by hand for a few threads to ensure they are not cross treaded. Then, run the nuts down the threads using the impact on minimum trigger pull to seat them against the wheel. Then I use the torque wrench to start tightening them in the proper pattern to about half the torque value then again to the full torque value. I haven't had a wheel fall off or ever broken a stud.

Okay for your question : I would say it's all about the calibration that has been done. You are asking about accuracy, but that's the problem. The testing/calibration process can show the value is anywhere from +1-10ftlbs over the indicated/selected value when tested. So the specific type of tool or the tool working range doesn't matter. I could have one TQ wrench at 10-150ftlbs range that doesn't exceed +2ftlbs at any selected value. I could have one TQ wrench at 20-300ftlbs range that exceeds +4ftlbs at all selected values. Which one would YOU use???
It doesn't matter the TQ range of the wrench when tested and calibrated. 150ftlbs is 150ftlbs....as long as you know WHAT it showed for calibration that's most important.

What matters more is, has the tool been calibrated using national standards?? There's plenty of commercial businesses that require this to be done, to that there's plenty of off-site companies that provide this calibration service.
The specific tool being used IS NOT going to be SO much more accurate side-by-side. Sure we can get 10 different torque wrenches, have all of them calibrated. Are you going to pick the most accurate one, or the one with the greatest range of TQ capability (IE : 20-250ftlbs compared to 50-150ftlbs)???

Unless you have some real world requirement to have such "specific type and accurate" TQ wrench to use for the lug nuts, spend your money on a quality tool and use it. Some will give a basic test paper showing the tested ranges the manufacturer QA'd the tool before it left there facility.

:cool: :cool: :coffee: :coffee: 🇺🇲 🇺🇲 🇺🇲 🇺🇲
 
I buy my straps from Ratchet Straps, I usually buy custom ones. They are sewn here in Ohio.
They will even break down where the ratchet, end connection etc are manufactured.
That might be who makes the USA made straps for Mytee. They advertise them as being made in Ohio. That’s where my wheel straps for the ATV are made.
 
Last edited:
Anyone install bumper spacers have a solution to this bumper gap. I put 3/4 inch spacers on this week in prep of the lift kit coming to keep my offset and go as large as possible tire size probably end up 38x13.5r18 nitto ridge grapplers. I know on my 2017 I needed them to clear the 38s.
 

Attachments

  • 20260607_200929(1).webp
    20260607_200929(1).webp
    457.1 KB · Views: 34
  • 20260607_201444.webp
    20260607_201444.webp
    385.6 KB · Views: 37
We crossed into Canada a lot on our Harley’s always travel with my buddy and wife who a LEO and they always asked her if she had handcuffs? :unsure: She always said no but I carry a key. Then they just waved us through.
I left them on the bed post.:ROFLMAO:
 
Easiest 11.6" Rear Diff Service ever.

Unscrew the M18 GOLD PLUG and let'er rip

1780879466474.webp




This is why I only use GOLD PLUGS --> They pick up all magnetic trash & super fine particles like glue !

The plug on the left is the new Fill Plug. The plug in the Right was the drain plug I pulled from the photo above.

1780879635783.webp


These custom pan's with a fill plug, drain plug and a sight glass are available in the Tremor classifieds for sale
I'll be adding a 1/8" NPT temp gauge sensor port at the request of a member here on the forum on Custom Pans.


Tremor Axle service complete and ready to go..
Love that golden color.

1780879871763.webp
 
Last edited:
No I’m planning more like 30ish on the dempster!
This was on the Stewart cassiar highway through BC
Heh, yeah, those frost leaves are brutal. You liking the shocks overall?
 
Back
Top Bottom