🛠️ What did you do to your Tremor today? [2026 edition]

I was wrong. AI, which was not around 11 years ago when I was scratching this stuff out on my own, says you'd need to double up on the 4/0.

Obviously, the inverter needs to be much much closer to the battery bank, then with the inverter's 120V output you can simply run a 12/3 extension cord. (hey! we've gone from "wire" to "cable" and now we have "cord"!)

😝

Let me know if this AI search results link works for you.
 
If inverter, and if 3000W output, it's going to want a far larger copper stranded cross section that has 2AWG. If the inverter were right next to the battery bank *maybe* you could get away with 2/0 but over the length of the truck (figure 25' run, then we double that distance for the round trip in order to calculate for % amperage drop) the result should be 4/0 which weighs roughly 1 lb per foot. All this assuming a 12V system you're dealing with.

I swear one of these days I'm going to write a 'wire size' manifesto so I don't have to retype the same thing on every forum. :ROFLMAO:
It kills me when I see all these places selling 2AWG winch wiring kits. 2AWG really isn't big enough for a 12k winch.
I ran 1/0 to my front anderson connector, but it's less than 5 ft.
To the rear, I ran 2/0 which will have significant voltage drop at higher amps.
It should still work for my use case as long as I keep it's limits in mind.
But going bigger isn't practical. And there is no black & white correct answer to sizing.
It's a balance of theory and what actually works.
 
It's a balance of theory and what actually works.
Even with the correct gauge, the difference between "works" and "doesn't" can be as simple as one bad crimp...

Learned that the hard way on my 700Ah solar setup in my dirt bike trailer. Kept blowing fuses on the 12v side. 2/0 cable. One of the pre-made cables I got had a bad crimp and I was pulling my hair out trying to figure it out.

Finally replaced each 2/0 cable one by one with cables I crimped myself and no more blown fuses. It'll run a full 20a load on the 120v side for over three hours on battery alone, and quite a bit longer when the sun is out.

Low voltage and high amperage are pretty unforgiving.
 
Thank you Phil and McE for your posts.

[my little squaredrop system consists of three 105 Ah Odyssey Group 31 AGM connected in parallel to creat one 315Ah AGM battery. Since AGM are a sealed, VRLA battery there's no outgassing during charging. I put the inverter on a shelf directly above the battery bank but ventilated separately anyway.

Since I already had 1/0 "in stock" and felt too cheap to pony up for some new 2/0 I went with a 1500W pure sine SAMLEX inverter since I really only needed to run one of two 1400W galley applicances at a time. So I have 12.5 amps that can run for an hour and a half cumulatively but in reality less than 5 mins at a time. All I need. Too, there's an Engel MT45 compressor fridge that draws 1.5A when running typically a 33% duty cycle. I crimped all my own cable using an hydraulic crimp tool, marine copper stranded, marine lugs, marine heat shrink blah blah blah

I like the sound of the 700 amp hours battery bank, though, and a solid 20A, tell you what. Now that is a strong system.


It's a balance of theory and what actually works.


Ed Zachary.

While I strive to have less than a 3% voltage drop over whatever run I'm pondering, the reality is that sometimes (in the case of our 21' foot long Super Duties, with McE's being longer, more the length of the Queen Mary*), we have to consider duration of heavy amp "pull", wire diameter size vs. routing, cost, etc... I getchoo.

McE also brings up another common point: "If you want something done correctly, ya gotta do it yourself". /crimping

You fellers rawk. 🏁



*funnin' ya!
 
  • Like
Reactions: McE
Window tint today. 20% on the 3 sides and Pano roof. 70% front windshield with a 5% brow.
IMG_8621.webp
IMG_8620.webp
IMG_8619.webp
 
i haven't dealt with a compressor with a tank but a 1 gallon tank couldn't help that much. i looked up your Ryobi at 2.6cfm, off-roading airing up would be painful waiting to get all 4 tires back to hiway pressure. thor lightning & other compressors with 10.6cfm or more can save you a lot of time.
Installing 10+ CFM onboard air is really expensive. I like the flexibility of portable inflators but recommend two of the Milwaukee M18s instead. With two Milwaukee inflators you could inflate all four tires in under 15 min (one pair at a time) for less than a third of the price of onboard air.

The spec on that Ryobi is actually only 0.75 SCFM @ 40psi. The reservoir and all that hose is just extra volume to fill when filling tires.
 
Back
Top Bottom