🛠️ What did you do to your Tremor today? [2026 edition]

Just a little sound clip of the KC Jetfire. It’s not too different than stock but sounds a little more like 17-19 6.7 and maybe even a touch of 6.0 PSD. It’s hard to pick up in the video but in the cab you can definitely hear the turbo pulling more air and the ball bearing sound. Driving wise it absolutely rips and when you’re in boost it just wants to take off.
 

Attachments

  • IMG_6602.mov
    24.9 MB
Also you are not completely draining the diff. there is fluid in the tubes all they way to the oil bathed hubs. My advise is don't sweat it. Now if you drain the hubs out as well you might get close to the right qty of fluid but then you should set each side of the axle up in the air on a jack stand one at a time to force fluid to the hubs.
Good point. I’m not sweating it either way. Just found it interesting.
 
I’m almost done with this project. Just have to wait until it’s dry to run the wiring. For various reasons it took me 10x longer than i thought it would to figure it out. Wiring 17 pods in total, it’s a puzzle of wire amperage, gauges and distances.
any luck buttoning up your wiring?
how did it turn out?
 
Plugging along
 

Attachments

  • IMG_2293.webp
    IMG_2293.webp
    260.7 KB · Views: 56
  • IMG_2292.webp
    IMG_2292.webp
    324.7 KB · Views: 55
any luck buttoning up your wiring?
how did it turn out?

I’m still at it. I pretty much gutted everything i had prior and did everything from scratch, following some of the best practices i learned over the last few years. course it is days not hours of work. But after this i will confident that it is done right, i hope:-)
 
Also you are not completely draining the diff. there is fluid in the tubes all they way to the oil bathed hubs. My advise is don't sweat it. Now if you drain the hubs out as well you might get close to the right qty of fluid but then you should set each side of the axle up in the air on a jack stand one at a time to force fluid to the hubs.
Tubes do hold oil and should be drained as well, especially in a high mileage/high stress environment. One way I do this is start my tear down on an afternoon/evening and then let it sit until the next morning or day. And to ccradier point if you can jack one side of the axle up for a few hrs and then the other……even better.

Course you need time and not be in a rush to have your truck back.

50 yrs ago when my Dad taught me this, it was not easy to just let my rig sit…… now that I’m retired, it’s a bit easier. 🤠
 
If you are diligent with your maintenance and have no failures you draining the center should be enough. However in low fluid conditions or when you have a metal failure i s highly advised to pull the shafts and hubs, remove the cover and clean every knook and cranny. The gear oil we have today is pretty damn good. I have a customer with a 22' gt 500 and though he doesn't tow he runs the crap out of that machine. He has seen 250 degree rear diff temps doing over 170 for 20 minutes. I drained the fluid and it looked good. Nothing in it. So refilled and away he went. I think water intrusion would cause more of a reason to go all the way with a service.
 
Loaded up for my vacation road trip from Orlando to the Arctic Ocean via the dempster highway
Camping out of the bed of the truck along the dempster

View attachment 258205

Looks very well organized! Safe travels! Sounds like an awesome trip ahead.
 
Did this yesterday... Diode Dynamics SS6 Pro fog light kit. Overall super happy with the results especiallythe light output, but I will admit up close the "fit" is a little lacking and I wish they were 1/2" longer to really fill the backside of the bezel.
2cfde852-73c3-41fd-a0a4-8711cf788975.webp
 
Last edited:
Loaded up for my vacation road trip from Orlando to the Arctic Ocean via the dempster highway
Camping out of the bed of the truck along the dempster

View attachment 258205
Thats awesome! I leave Texas on 6/9 to head to Palmer, Alaska to pick up my custom slide-in truck camper from Cache Camper. On the way up taking the Cassiar Highway and unfortunately will be hoteling it on the way up. My wife and sons (14/10) are flying into Anchorage on 6/18 and then we are spending a week in Alaska (Denali NP, Kenai Fjords NP, and Wrangell St. Elias NP). My wife will fly home and then me and the boys are headed up the Dempster to the Arctic Ocean before coming back south on the Alcan with a couple stops along the way a the Sign Post Forest, Liard Hotsprings, some Canadian NP (Jasper, Yoho, and Banff) and then returning to the US and stopping at Glacier NP, Theodore Roosevelt NP, Mt Rushmore, and Windcave NP.

I've got the Outdoor kitchen all set up. A 37x12.50 spare in the factory location (Carli Trophy Hitch) and a 37x12.50 spare on the Rigd UltraSwing

IMG_1811.webp


IMG_1813.webp
 
awrsome trip

good luck gentlemen

you're in for a long haul

@18FLHP

if you're doing denali, very emphatically recommend talkeetna, air taxi up & land on the glacier on denali.

pricey but you'll be glad you did.

20240920_175439.webp
20240920_175556.webp
20240920_175425.webp
20240920_162313.webp
 
Last edited:
Back
Top Bottom