🛠️ What did you do to your Tremor today? [2026 edition]

The power steps look awesome. I am trying to decide between the XL and extreme. Both seem to have features I am looking for. Looking for lowest step drop, wide steps, and ideally smart phone control. What steered you to the XL?
 
Those center console mounts seem hard to find. The online store shows them sold out.
That is because they will not ship to Canada. I bought and sent one to my Brother in Edmonton. BuiltRight might ship to Canada
 
The power steps look awesome. I am trying to decide between the XL and extreme. Both seem to have features I am looking for. Looking for lowest step drop, wide steps, and ideally smart phone control. What steered you to the XL?
I was deciding between the regular powersteps and the XL. Not sure the extreme's were necessary (with 4 motors, since one motor per side seems sufficient) The XL versions have the housing that acts as rock guards and also drops the steps about 3 inches lower than the regular ones. I actually like the look of the housing. If you are looking for the lowest drop the XL's are the way to go. My wife and kids really appreciate the lower drop. Good luck!
 
Last edited:
Used 4WD for the first time climbing up to this campground. On a paved road! (It was steep and raining and I had the rears at 75 psi with only around 5klb on the rear axle.)

Tennessee is beautiful but rainy.

IMG_5150.webp
 
Installed the @MVI rear diff cover with sight glass, magnetic drain plug and fill port.

Still stunning to me that you can’t get those plugs from the factory like I did in my ‘83 S-10. Hopefully this is the last time that cover needed to come off.

Very well packaged, included everything needed but the gear oil and came with a very detailed set of instructions.

Best of all, my diff cover doesn’t say peepee on it or have the dad from Mary Poppins name on it and I can get the specced amount of oil in through the fill port.

IMG_6501.webp

IMG_6502.webp

IMG_6503.webp

IMG_6505.webp
 
37x12.5 brand new spare on oem 18” wheel in stock location
Had to chop the exhaust shortly after axle dump just before the final hanger to make a modified side exit axle dump setup. I have 5” turbo back pipe on the truck and it was blocking the tire from going all the way up

Got 5psi in the tire
IMG_8063.webp
IMG_8066.webp
 
I have a 2026 F250 Lariat Ultimate on order, 5 more weeks 🤞, and based on these types of messages I think I will be upgrading my front and rear differential covers much sooner than planned just to check and replace axle lube and to insure leaves.
 
Just an fyi related to my diff cover change post. The manual specifies 4.33-4.44 quarts for the 11.6 rear end without the 4.30 gears from the gas engine. Mine had less than 4 from the factory. Thanks Ford.

View attachment 258041
Fortunately hypoid gears are relatively tolerant of low lube levels!
I have a 2026 F250 Lariat Ultimate on order, 5 more weeks 🤞, and based on these types of messages I think I will be upgrading my front and rear differential covers much sooner than planned just to check and replace axle lube and to insure leaves.
Check the levels and then put 500-700 miles on em. Let the gears mesh. Then change it.
This is what was in the bottom pit of the front axle after 100ish miles in 4wd. 6000 on the truck.
IMG_1684.webp
 
Also you are not completely draining the diff. there is fluid in the tubes all they way to the oil bathed hubs. My advise is don't sweat it. Now if you drain the hubs out as well you might get close to the right qty of fluid but then you should set each side of the axle up in the air on a jack stand one at a time to force fluid to the hubs.
 
I’m about to need to rotate my tires so I went ahead and bought a set of gloss black take offs. Now I can do a 5 wheel rotation. I still need to get the TPMS before installing.
 

Attachments

  • IMG_1882.webp
    IMG_1882.webp
    180.3 KB · Views: 23
Last edited by a moderator:
Just an fyi related to my diff cover change post. The manual specifies 4.33-4.44 quarts for the 11.6 rear end without the 4.30 gears from the gas engine. Mine had less than 4 from the factory. Thanks Ford.

View attachment 258041

As some others have mentioned, if it were possible to get ALL the diff fluid out you might see that to be the proper level of fluid. Not a biggie burger to worry about.

:cool: :cool: :coffee: :coffee: 🇺🇲 🇺🇲 🇺🇲 🇺🇲
 
Back
Top Bottom