🛠️ What did you do to your Tremor today? [2026 edition]

Sorry for blowing up this post 😂 but figured yall might want to follow along with all that goes into this. Crank gear welded below 5/8 long welds in 4 spots.
IMG_8584.webp
 
Trying to find a blackout grille to replace the chrome. Heck of a time so far. Have the badges, side emblems, etc already.
Ebay is the best place to go for this of you don't mind a non-Ford brand. If you want it to be OEM parts then I'd recommend BFN Truck shop
 
Sorry for blowing up this post 😂 but figured yall might want to follow along with all that goes into this. Crank gear welded below 5/8 long welds in 4 spots.
View attachment 257430
Not at all!!! We are here for shiny things that create heat and smoke. Continue please.
 
Well yeah when you're that high 🤪.

Present company has practical experience. I'm surprised there's no O2 mask system installed.
😆 😆 🤣 🤣 🤣 🤣 🤣 🤣 🤣 🤣

Turbo and EGR are off. Front cover coming off next.

Request : Could you find the transfer case and transmission vent connections and point them out?? They should be on the high points of both, then the tubing runs up to the firewall. TIA!!
 
Sorry for blowing up this post 😂 but figured yall might want to follow along with all that goes into this. Crank gear welded below 5/8 long welds in 4 spots.
View attachment 257430
Should totally make this build its own post, something that should be searchable to find great pic and process!
 
80107804762__B7E5E644-871D-4A81-A4E4-26A455C32A4D.webp

The cab is back on, coolant, fresh oil, oil & fuel filters. Truck fired right up and no codes. Need to button up the fender liners and clean up a bit. Tomorrow I’ll flash the DCR optimized KC Turbo file (175+ hp file) and go on a long test drive. First impressions are the sound isn’t too much different from stock (what I wanted) but it definitely sounds different.
 
Nothing screams "I'm about to go drop off some dead bodies out in the back wood line." like that setup. 🤣 🤣 🤣 🤣🔪🔪🔪🔪🔪🔪

:cool::cool:🇺🇲🇺🇲🇺🇲🇺🇲
Soooo.... The first iteration of my drawer slide didn't work as well as I had hoped. So, going with your imposed theme, I am going in a different route. 😜☠️
1000015058.webp
 
PMF's suspension stuff arrived yesterday. I think the total pallet weight was 550 lbs. Roughly looks like end of May is when everything will be here and go on the truck (still waiting on wheels and tires). Felt like Christmas Morning!
IMG_0519.webp


Suited and booted and ready to roll Tuesday for install day.
2 things my KMC Impact FFT wheels 18x9 with 0 offset were supposed to be in stock by now (ordered 4/29). Was told they are delayed until mid June now. Had to pivot and go with the +18mm offset instead and then going to run a 10 mm slip on spacer.

38x11.5x18 Nitto ridge grapplers were also supposed to be in the build, sadly couldn't get here in time from the warehouse. Settled on 37x12.5 Toyo RT Trail's (which they also make in 38x11.5 but I cannot find them, maybe in a few years when I run through these tires). 38x11.5x18 are just a rare uncommon size tire.

Stuff happens, bummer, it is what it is. My fault as I scheduled install day for this Tuesday before I had everything on hand. In the end, not the biggest things in the world!! Could be worse. Enjoy everyones long weekend!
 
Funny watching the series. I had the same job as him. To a broader extent. Not the murder part, the investigation part.

For clarity.

I have stories.
I would let him keep working if I found him out 😜
 
Life gets busy and sometimes it’s good to admit when it just looks good at the mall 😂
Yes sir, I say this about the ladies too! 🤪
 
Installed AMP Powersteps XL and love them! They do make a clunk sound when they retract, but I suppose that's normal.
 
Back
Top Bottom