PPE Sterling 11.6 Differential Cover

xrocket21 · Dec 1, 2024

Anyone know the part number for the oem rear gasket? Thanks!

MVI · Dec 1, 2024

xrocket21 said:
Anyone know the part number for the oem rear gasket? Thanks!

PC3Z 4036 A

Gasket for a 2024 F350 Tremor with the 11.6 Sterling

Hunterman · Dec 1, 2024

When you guys install a new cover do you use any sort of sealant? If so what do you use? I’m going to probably replace mine with the Banks (because I can) just for the ease of draining and filling without having to take the cover off. I like to replace all my fluids every 25k miles and I’ll be there pretty soon.

ccmac · Dec 2, 2024

Hunterman said:
When you guys install a new cover do you use any sort of sealant? If so what do you use? I’m going to probably replace mine with the Banks (because I can) just for the ease of draining and filling without having to take the cover off. I like to replace all my fluids every 25k miles and I’ll be there pretty soon.

If you are planning on using banks that implies you have a Dana M275- they already have a drain plug, on Dana m275 the bottom right hand cover bolt is a drain plug.

4x4captain · Dec 3, 2024

Will the banks cover for with the Hellwig sway bar installed?

DTX2023Tremor · Dec 3, 2024

Hunterman said:
When you guys install a new cover do you use any sort of sealant? If so what do you use? I’m going to probably replace mine with the Banks (because I can) just for the ease of draining and filling without having to take the cover off. I like to replace all my fluids every 25k miles and I’ll be there pretty soon.

You'll want to use Motorcraft TA-31 silicone sealant: https://amzn.to/41RnWwc

xrocket21 · Dec 3, 2024

4x4captain said:
Will the banks cover for with the Hellwig sway bar installed?

Oooo , that's a good point, I hope the PPE cover fits with my Hellwig sway bar

gmbpilot757 · Dec 3, 2024

4x4captain said:
Will the banks cover for with the Hellwig sway bar installed?

The Banks website says they will not fit the Sterling (12 bolt) rear-end with a swaybar. Doesn’t say anything about the Dana (14 bolt).

Abuck99 · Dec 3, 2024

Hunterman said:
When you guys install a new cover do you use any sort of sealant? If so what do you use? I’m going to probably replace mine with the Banks (because I can) just for the ease of draining and filling without having to take the cover off. I like to replace all my fluids every 25k miles and I’ll be there pretty soon.

DTX2023Tremor said:
You'll want to use Motorcraft TA-31 silicone sealant: https://www.amazon.com/Genuine-Ford-TA-31-Silicone-Sealant/dp/B000NUD02W

As an alternative to OEM sealant, this works very well on sealing up diffs

The Right Stuff Black 1-Min Gasket Maker, 5 OZ | Permatex®

Replace cut gaskets in one minute. Install parts immediately. OEM-approved. Oil and coolant resistant.

www.permatex.com

xrocket21 · Dec 4, 2024

you put sealant on both sides of the gasket?

DTX2023Tremor · Dec 4, 2024

xrocket21 said:
you put sealant on both sides of the gasket?

The sealant is usually for if there is no gasket. I don't believe you need both.

usafakid09 · Dec 4, 2024

DTX2023Tremor said:
The sealant is usually for if there is no gasket. I don't believe you need both.

Correct; no sealant should be needed for 11.6 rear cover due to gasket.

xrocket21 · Dec 4, 2024

Ok thanks, that's what I thought. I have an oem gasket on the way.

I could have sworn I saw the torque spec somewhere in here, but I can't find it now. Anyone know?

usafakid09 · Dec 4, 2024

xrocket21 said:
Ok thanks, that's what I thought. I have an oem gasket on the way.

I could have sworn I saw the torque spec somewhere in here, but I can't find it now. Anyone know?

I think its in the PPE instructions...I'll have to look later today.

xrocket21 · Dec 4, 2024

usafakid09 said:
I think its in the PPE instructions...I'll have to look later today.

Maybe thats where I saw it. I was trying to look but their site is down.

Abuck99 · Dec 4, 2024

xrocket21 said:
Ok thanks, that's what I thought. I have an oem gasket on the way.

I could have sworn I saw the torque spec somewhere in here, but I can't find it now. Anyone know?

If you’re installing the PPE cover

xrocket21 · Dec 4, 2024

Thank you sir!

DTX2023Tremor · Dec 5, 2024

I added a note when ordering to see if they could powder coat the cover before sending it. It shipped pretty quick, so guess that was "no". I'll get it powered coated over the next few weeks and install it in a few months. PPE also came out with what looks like a compatible transmission pan, but that's out of stock, so hoping to confirm compatibility with the 23 gas engines so I can get that in and service all of it at the same time.

Lunch Box · Dec 5, 2024

DTX2023Tremor said:
I added a note when ordering to see if they could powder coat the cover before sending it. It shipped pretty quick, so guess that was "no". I'll get it powered coated over the next few weeks and install it in a few months. PPE also came out with what looks like a compatible transmission pan, but that's out of stock, so hoping to confirm compatibility with the 23 gas engines so I can get that in and service all of it at the same time.

When i ordered my 3 from PPE, they had different part numbers for raw, powder coated etc?

DTX2023Tremor · Dec 5, 2024

Lunch Box 🥩🍔 said:
When i ordered my 3 from PPE, they had different part numbers for raw, powder coated etc?

Yeah, for other products I've seen the option to choose the finish. For the diff cover, they didn't offer the option so I figured it didn't hurt to ask. A quick search online looks like I can get it powder coated for $50 - $100