Adding lighted platinum sill plates

Has anyone got an easy workaround for those without the factory plug? I'm assuming there's numerous potential tie-in sources, but are there any more convenient to the silly plate?
 
Has anyone got an easy workaround for those without the factory plug? I'm assuming there's numerous potential tie-in sources, but are there any more convenient to the silly plate?
According to everything I've researched, the running board lamps are driven with the puddle light circuit. These are all White wires, and the ground return is the Blue/grey wires. (Or chassis) This circuit drives all of the scuff plate lamps, trailer assist lamp, and cargo lamps. The cargo lamp return is Black Violet.

You could likely tap into this circuit to light the running boards. (This is for LED lamps; without LEDs the wire will be White/Green and only drives the high mounted cargo lamp, but you could likely also tap into that.)

Hope this helps.
 
Has anyone successfully install the lighted sills on a 25 or a 26? I have a 26 and ordered the sills but the connector was removed. Looking for info on what wires to tap to make the sills light up as they normally would when the doors open.
 
Has anyone successfully install the lighted sills on a 25 or a 26? I have a 26 and ordered the sills but the connector was removed. Looking for info on what wires to tap to make the sills light up as they normally would when the doors open.
My 24 had the connectors so I literally just pulled the ones out of my 22 and resoldered the connectors back on and it was plug and play. I will say it was a PIA on my 22 to find the wires to tap into and ended up doing what others suggested which was tap into the wire feeding the cargo light which is activated when the doors are opened.
 
Has anyone successfully install the lighted sills on a 25 or a 26? I have a 26 and ordered the sills but the connector was removed. Looking for info on what wires to tap to make the sills light up as they normally would when the doors open.
Power (Positive): Look for the Grey wire with a Violet (Purple) stripe.
Crucial Note: You will likely see two wires with this exact color scheme in the harness. One will be twisted with an orange wire, and the other will be running by itself. You must tap the Grey/Violet wire that is sitting by itself.

Ground (Negative): Look for the Black wire with a Purple stripe.
Alternative Ground: You can also tap the Black wire with a Yellow stripe. Alternatively, you can crimp a ring terminal to your sill's ground wire and secure it directly to a clean, unpainted factory chassis ground bolt under the dash or sill.
 
Has anyone got an easy workaround for those without the factory plug? I'm assuming there's numerous potential tie-in sources, but are there any more convenient to the silly plate?
What trim level is your truck? You could tap into the ambient lighting in the footwells.
 
What trim level is your truck? You could tap into the ambient lighting in the footwells.
Platinum. I'd really like to install them but when I looked at all those bitty multi colored wires I figured I'd screw things up. Just can't underestimate Ford cost cutting cheapness... why not just put the damn plug in, regardless if the truck has fixed steps or deplorable.
 
Power (Positive): Look for the Grey wire with a Violet (Purple) stripe.
Crucial Note: You will likely see two wires with this exact color scheme in the harness. One will be twisted with an orange wire, and the other will be running by itself. You must tap the Grey/Violet wire that is sitting by itself.

Ground (Negative): Look for the Black wire with a Purple stripe.
Alternative Ground: You can also tap the Black wire with a Yellow stripe. Alternatively, you can crimp a ring terminal to your sill's ground wire and secure it directly to a clean, unpainted factory chassis ground bolt under the dash or sill.
I'll be looking at this over the weekend. I'll report back once I check it out. Thanks.
 
Platinum. I'd really like to install them but when I looked at all those bitty multi colored wires I figured I'd screw things up. Just can't underestimate Ford cost cutting cheapness... why not just put the damn plug in, regardless if the truck has fixed steps or deplorable.
If you want this to be plug and play, I will take some measurements this weekend and build a harness. Should be able to route from footwell into A pillar, then into rocker tray.

On the lighted sills, where are the connections? Center of door? Towards front? Rear?
 
If you want this to be plug and play, I will take some measurements this weekend and build a harness. Should be able to route from footwell into A pillar, then into rocker tray.

On the lighted sills, where are the connections? Center of door? Towards front? Rear?
@NEOHIO - The sills sit about middle of the door and the plug is about middle as well.
 
If you want this to be plug and play, I will take some measurements this weekend and build a harness. Should be able to route from footwell into A pillar, then into rocker tray.

On the lighted sills, where are the connections? Center of door? Towards front? Rear?
I’d be interested. If you need details on the plug on the lighted sills let me know. I’d like a plug and play option. I’d prefer to plug in rather than splicing wires.
 
I’d be interested. If you need details on the plug on the lighted sills let me know. I’d like a plug and play option. I’d prefer to plug in rather than splicing wires.
I have the all the connectors in stock, the ones for the lighted sill, as well as the ambient lightings connectors.
I need to confirm pin-out on both pieces & figure out lengths.
Just waiting on terminals and cable seals. I will mock up some lengths this week.
 
I have the all the connectors in stock, the ones for the lighted sill, as well as the ambient lightings connectors.
I need to confirm pin-out on both pieces & figure out lengths.
Just waiting on terminals and cable seals. I will mock up some lengths this week.
Let me know if you make one for the 22's. It's silly that Ford got rid of the lighted sills, even sillier for the Platinums. You'd think they'd at least keep the connectors in there so we can add the sills in the future.
 
Let me know if you make one for the 22's. It's silly that Ford got rid of the lighted sills, even sillier for the Platinums. You'd think they'd at least keep the connectors in there so we can add the sills in the future.
I should hopefully have something built by this weekend. I will do some part number digging to see if your era truck has the same ambient lighting as the 23+.
 
I should hopefully have something built by this weekend. I will do some part number digging to see if your era truck has the same ambient lighting as the 23+.
Did you ever get anything put together?
 
I have all the connectors, terminals etc. I have made about 20 crimps with the tooling I currently own. I am not happy with any of them. I have 2 more crimpers coming Sunday or Monday. I hope one of them gives me the crinp I need.
Okay. Let us all know. I’m sure most of us would rather have a connection based solution versus splicing.
 
Has anyone successfully install the lighted sills on a 25 or a 26? I have a 26 and ordered the sills but the connector was removed. Looking for info on what wires to tap to make the sills light up as they normally would when the doors open.
Where did you order the light sills from?
 
Back
Top Bottom