🛠️ What did you do to your Tremor today? [2026 edition]

I put a 1/4 turn ball valve inline with the hose of my Valvo-max, I drain into used DEF jugs, when it starts getting full, I close the valve and swap jugs.
I did use some PEX style clamps on the ball valve to keep the hose in place. It has worked for me, just typically slow.
 
IMG_3866.webp


For the new tow rig
 
How do you like them? How’s the road noise. Between RT Trails, AT3’s, and Ridge Grapplers.
I did my research for weeks before I decided on the Trails. I had the at3s before and honestly the road noise difference isn't even noticeable. Their actually pretty quite. That was my concern before buying them as well.
 
I did my research for weeks before I decided on the Trails. I had the at3s before and honestly the road noise difference isn't even noticeable. Their actually pretty quite. That was my concern before buying them as well.


wWell now I owe you beer, you just saved me some cash with that review.
 
I actually found my 37” RT Trails to
be quieter/ride better than my 35” BFG KO3s when I swapped on my old rig. (And much better than my Toyo MTs however both sets had a lot of miles so were well aged.)
 
I must do a dash cam too.



Meanwhile, BMC at it again! Great idea, less than ideal execution.

The passenger side went in well enough, but the driver side BMC main bracket (neither bracket, actually - pass side shelf is angled up and driver, down - happened during fabrication and they're not easy to straighten) has a 90* shelf relative the rear brace. This makes for some frustation with any prealignment setup prior to intalling the assembly from under the front of the truck...

All I have to show for my efforts is a nearly-complete passenger side. Fine tuning lamp face rotation may occur later via the entire BMC bracket after I am victorious! in battle w/ the driver side. egh...

IMG_9592.webp


DD S3 SAE yellow fog w/ amber backlight + DD C2 white driving w/amber backlight - fogs are wired to the factory headlight switch loom, their amber backlight may be via an upfitter. The C2 driving lights have yet to be wired and to another upfitter. That's later.
 
Installed the Fumoto valve this morning as prep for installing the skid plate. Used the shop vac trick to pull the plug and install the valve, first time trying it didn’t slip a drop.
View attachment 260989
I've had these on my vehicles for 30+ years. I just changed the oil on the Tremor and connected a hose on the nipple to drain directly into DEF containers.
 
I must do a dash cam too.



Meanwhile, BMC at it again! Great idea, less than ideal execution.

The passenger side went in well enough, but the driver side BMC main bracket (neither bracket, actually - pass side shelf is angled up and driver, down - happened during fabrication and they're not easy to straighten) has a 90* shelf relative the rear brace. This makes for some frustation with any prealignment setup prior to intalling the assembly from under the front of the truck...

All I have to show for my efforts is a nearly-complete passenger side. Fine tuning lamp face rotation may occur later via the entire BMC bracket after I am victorious! in battle w/ the driver side. egh...

View attachment 261181

DD S3 SAE yellow fog w/ amber backlight + DD C2 white driving w/amber backlight - fogs are wired to the factory headlight switch loom, their amber backlight may be via an upfitter. The C2 driving lights have yet to be wired and to another upfitter. That's later.
I had to deal with this with my Rigid kit many moons ago with the Tundra. After a while of trying to get everything adjusted, I was about to start drop-kicking the OEM plastic bumper WWF-style to get everything to line up straight. Decided against the drop kick and paused it all and resumed the next day. Was a total pain in the ass but in the end got them working.

Not looking forward to this with the SD.
 
^ ^ ^ Right?

There aren't many options, either. I think Baja Designs offers something... but I already had purchased the BMC and the DD last year so it was a bit late to return it all to gamble on the BD.

I wish you a trouble-free install! but if you have any Qs, you know who to "aks".

:geek:
 
I have the exact same tire and size. Agree with every point, haha also came from AT3's before these as well.

I actually found my 37” RT Trails to
be quieter/ride better than my 35” BFG KO3s when I swapped on my old rig. (And much better than my Toyo MTs however both sets had a lot of miles so were well aged.)


Awesome to hear! Thanks guys.
 
^ ^ ^ I've had Fumotos on both my F150's Coyote engine and now my F350's Godzilla... both valves have barbed fittings to shove a short length of clear vinyl tubing and directly into a 12-quart plastic oil drain jug. Easy peasy. The messiest part is the awl filter.

I had never considered installing a drain valve on my oil pans and then not able to use tubing to a used oil recepticle. You guys a few posts above should avail! yourselves of the oil valve tubing miracle!

lmao
Fumoto makes a little snap on piece that will hold the hose on to the valve.
 

Leadsledz49, WinterWarlock21, ramv I'm coming from a set of 37 Nitto Recon Grapps and am mainly highway cruising, so you're saying the RT Trails have no more road noise than the Falken AT3?​


Almost positive they are talking about Toyo AT3.

For what it’s worth, I’m coming from a 3rd Gen Tacoma with Falken at3w and they got loud around 35k miles. I was a little disappointed with the noise and the longevity of them even with consistent rotations and alignments.
 
Fumoto makes a little snap on piece that will hold the hose on to the valve.

Yah. That little white plastic snap-on fitting is fragile, too. The larger i.d. that clicks onto the brass Fumoto likes to split/crack.

The Fumoto on my Coyote F150 is all brass which was what I had wanted when I bought the Fu for my Guzillier.

What I was trying to say earlier was that I could not conceive of buying a Fumoto valve that didn't accept tubing. That was the main reason for it's purchase! and not for just a drain switch.

😝



Meanwhile, after dinner... I tossed the driver side up in there using slightly taller stainless fender washer stacks to compensate for the BMC's poor fabrication (remember, I could not use the BMC supplied brackets because they were wrong, twice) and got 'em pretty closely aligned.

These are Diode Dynamics' "SAE" lumens level yellow fog lights (the weakest, in an attempt at being D.O.T. legit) fogs. They do have a distinct cutoff which is great.

Here is standing 40' feet away w/ phone camera (in telephoto) at eye level

IMG_9596.webp




Here is squattin' to put the camera near fog light center-height level

IMG_9597.webp




My amber backlights are not yet wired up.
 
Back
Top Bottom