🛠️ What did you do to your Tremor today? [2026 edition]

I was terrified. But got my TPMS adjusted and Bambi mode turned on without any drama. Admittedly these were easy ones.
I did those first too and the double honk kill. Then day before yesterday I did the auto hold, which required 3 steps. Still simple. I save a new file for every change I make. Makes it easy to back track in case something goes wrong.
 
Probably the first two for me also.

Is the TPMS a LOW only warning? So if I set it for daily and add 20lbs to tow, it wont alarm?

Correct, there is only a low threshold setting.


The default is low threshold setting. So if you normally run say 55 psi and set it to 55psi. You will see the light pretty often. Recommend setting it at least 5-10 psi less than whaT you typically run in your tires. Airing them up will not set off the light. However, there is another setting in there (right next to the adjustment) to set the psi as a high threshold. So if you go over PSI it will trigger the light. You cannot set both though. One or the other. Which, honestly would be nice if you could do both.
 
Adjusted some more Forscan settings yesterday. Some I am not sure if they do anything yet.

IPC
Disable - front/rear brake assist (i had it disabled from the infotainment screen, but added it here too)
enable - oil pressure gauge (just shows the oil can and the sweep graph, no numbers to enable which is strange)
disable - chimes key in ignition reminder
enable - intelligent adaptive cruise control speed tolerance (haven't tried to find this yet)
enable - navigation/compass (shows in cluster on bottom)
enable - off road tire pressure (haven't tried to find this yet)
disable - park aid control rear blockage warning (this truck really hates my bike rack haha, in conjunction with rear brake assist)
enable - global window open/close (not sure if this changed anything from previous, had to change multiple modules initially but this one was missing)

BdyCM
TPM Front 60 to 50
TPM Rear 75 to 50 (might lower this to 45)

APIM
enable - curve speed control menu (haven't tried to find yet but hate that the truck throttles me around sharpish corners on the HWY)


Initial changes when I got the truck:
enable - Bambi Mode (High Beams / Fogs)
enable - Global Open/close (Front Windows)
disable - Triple Ding at Start Up
disable - Seatbelt Chimes / Screen
change - Turn Signal Flash - 5 Blink (3 OEM)
disable - Double honk for keys in truck
 
Installed the Fumoto valve this morning as prep for installing the skid plate. Used the shop vac trick to pull the plug and install the valve, first time trying it didn’t slip a drop.
IMG_1715.webp
 
Has anyone ever tried using a suction tool on oil drains to speed up the process?
Something like this extractor?
View attachment 260998
I use this exact pump for my boat motor because getting to the "drain" hole is not easily accessed. I would think it would be hard to use on the truck and not sure it would be any faster than a Fumoto. Interesting idea though.
 
I use this exact pump for my boat motor because getting to the "drain" hole is not easily accessed. I would think it would be hard to use on the truck and not sure it would be any faster than a Fumoto. Interesting idea though.
When you have to drain 4 gallons, any speed increase is worth it!
I found the Fumoto on my F150 seemed to take forever to drain using silicone tubing.
I went with Valvomax on this truck, it feels like it is quicker, but does require a used oil swap 1/2 thru.
 
Adjusted some more Forscan settings yesterday. Some I am not sure if they do anything yet.

IPC
Disable - front/rear brake assist (i had it disabled from the infotainment screen, but added it here too)
enable - oil pressure gauge (just shows the oil can and the sweep graph, no numbers to enable which is strange)
disable - chimes key in ignition reminder
enable - intelligent adaptive cruise control speed tolerance (haven't tried to find this yet)
enable - navigation/compass (shows in cluster on bottom)
enable - off road tire pressure (haven't tried to find this yet)
disable - park aid control rear blockage warning (this truck really hates my bike rack haha, in conjunction with rear brake assist)
enable - global window open/close (not sure if this changed anything from previous, had to change multiple modules initially but this one was missing)

BdyCM
TPM Front 60 to 50
TPM Rear 75 to 50 (might lower this to 45)

APIM
enable - curve speed control menu (haven't tried to find yet but hate that the truck throttles me around sharpish corners on the HWY)


Initial changes when I got the truck:
enable - Bambi Mode (High Beams / Fogs)
enable - Global Open/close (Front Windows)
disable - Triple Ding at Start Up
disable - Seatbelt Chimes / Screen
change - Turn Signal Flash - 5 Blink (3 OEM)
disable - Double honk for keys in truck


This seems like everything I would want to change.
 
Installed the Fumoto valve this morning as prep for installing the skid plate. Used the shop vac trick to pull the plug and install the valve, first time trying it didn’t slip a drop.
I just learned about this method a few weeks ago and tried it for the first time to do the exact thing you did. F316L FTW. I had the same one on my 2012 F250 for 8+ years and never a drop leaked out.

When you have to drain 4 gallons, any speed increase is worth it!
I found the Fumoto on my F150 seemed to take forever to drain using silicone tubing.
I went with Valvomax on this truck, it feels like it is quicker, but does require a used oil swap 1/2 thru.
Do you change your oil when it is at full operating temp? The fumoto works best that way. If its cold it will take a very long time.
 
I just learned about this method a few weeks ago and tried it for the first time to do the exact thing you did. F316L FTW. I had the same one on my 2012 F250 for 8+ years and never a drop leaked out.


Do you change your oil when it is at full operating temp? The fumoto works best that way. If its cold it will take a very long time.
i change my oil when it's hot and let it sit overnight. that works well for me. i also use mr. fumoto.
 
Has anyone ever tried using a suction tool on oil drains to speed up the process?
Something like this extractor?
View attachment 260998
I’ve used them through the dipstick hole, and through the TC fill hole. Not through the Fumoto valve. I’m sure it would help, but I just go on to something else. Like checking fluids levels, cleaning the windows, etc.
 
I just learned about this method a few weeks ago and tried it for the first time to do the exact thing you did. F316L FTW. I had the same one on my 2012 F250 for 8+ years and never a drop leaked out.


Do you change your oil when it is at full operating temp? The fumoto works best that way. If its cold it will take a very long time.
Always after driving home. Oil temp at 190+ according to Banks gauge
 
Installed the Fumoto valve this morning as prep for installing the skid plate. Used the shop vac trick to pull the plug and install the valve, first time trying it didn’t slip a drop.
View attachment 260989
@mrmag00 - Two questions:

1. Do you have the 6.7 or 7.3?
2. Which skid plate are you going with?

I have the Juggernaut plate and the 6.7 . The oil drain cutout on the Juggernaut is a little too far back and the oil drips on to it when it starts to flow straight down. I have the Fumoto valve as well, and hoped this would fix the issue, but it doesn't.

I now use a shortened funnel between the fumoto drain valve and the skid plate. The funnel top is large enough that it won't go through the skid plate opening, so it just rests there and now directs all of the oil into my bucket.
 
Yes a Juggernaut skid plate and it’s a 6.7 was going to just put a hose on it when changing the oil.
 
Yes a Juggernaut skid plate and it’s a 6.7 was going to just put a hose on it when changing the oil.
I have the Talon plate and the Sthalbus drain valve and find that having a hose from the valve to the drain pan makes it a much cleaner oil change. Silicone tubing holds up pretty well and for the Fumoto, might add a hose clamp on one end so you can do other things and won't have to monitor the hose coming off the valve.
 
^ ^ ^ I've had Fumotos on both my F150's Coyote engine and now my F350's Godzilla... both valves have barbed fittings to shove a short length of clear vinyl tubing and directly into a 12-quart plastic oil drain jug. Easy peasy. The messiest part is the awl filter.

I had never considered installing a drain valve on my oil pans and then not able to use tubing to a used oil recepticle. You guys a few posts above should avail! yourselves of the oil valve tubing miracle!

lmao
 
Always after driving home. Oil temp at 190+ according to Banks gauge

Nothing like reliving the Middle Ages, storming castles, defending the wall with hot oil..... 🤣 🤣 🤣 🤣 🤣 🤣 🤣 🤣 🤣 🤣

Spill a little bit of the hot oil causes one to start thinking about how NOT to spill hot oil.

:cool::cool::coffee::coffee:🇺🇲🇺🇲🇺🇲🇺🇲
 
Back
Top Bottom