🛠️ What did you do to your Tremor today? [2026 edition]

All of my Forscan programming is completed. Actually nothing more I can do than what the 2026 options on the spreadsheet allow me to do at this point in time. The light bar with the DRL option is wired into my Upfitter switches. Switch #3 is high intensity WHITE and Switch #4 turns on the DRL feature. Not automatic when the vehicle turns on so I can manually control through Upfitter. Switch #1 are my reverse lights rom the the April Group Buy and Switch #2 will be my Dirtcom Trailguard lights when my bar arrives.
It just threw me off seeing your lower lights on. I didn't think they were part of the DRL circuit.
 
It just threw me off seeing your lower lights on. I didn't think they were part of the DRL circuit.
Totally get it...took this pic yesterday evening. I do like that my FOGS now come on automatically as soon as the headlights kick on too!
 
Been in production since 6/12. This waiting game is killing me.

The tracker usually shows "In Production" earlier than your build week. If I remember correctly, this is your build week (6/22). A date will populate above/below the "In Production" on the tracker when it is actually being built. You are almost there!
 
Been in production since 6/12. This waiting
Mine showed in production for almost 2 weeks. Then it updated to built and shipped all at once. That included the spray in bed liner. This was back in late Feb/early Mar. You are close to getting your truck.
 
Can you confirm or deny that a standard click type torque wrench is typically more accurate when in the middle of it's range? Such as 150 ft lbs for our lug nuts using a 10-150 scale wrench vs a 25-250 scale wrench? This is just what I remember reading in the past. I'm certainly no expert.

I typically install the nuts on the studs by hand for a few threads to ensure they are not cross treaded. Then, run the nuts down the threads using the impact on minimum trigger pull to seat them against the wheel. Then I use the torque wrench to start tightening them in the proper pattern to about half the torque value then again to the full torque value. I haven't had a wheel fall off or ever broken a stud.
Older post, but falls into my forte as a reliability mechanical engineer, that spends most of my time looking at bolted assemblies. We typically assume +/- 25% from click type or digital torque wrenches with properly lubricated threads, can achieve about +/- 10% with Hytorque in my experience. For critical service we always use turn of nut or bolt stretch/strain gauges for precision applications. Thread type (coarse, fine, and ultra-fine) and lubrication play a major role as well. Basically none of this applies to lug nuts, but thought I'd share.
 
IMG_5478.jpg

Added an F4 Sneak Attack for anyone trying to carjack me at an intersection!
 
The tracker usually shows "In Production" earlier than your build week. If I remember correctly, this is your build week (6/22). A date will populate above/below the "In Production" on the tracker when it is actually being built. You are almost there!

Spot on. Updated to production on 6/12. Good insight.

Mine showed in production for almost 2 weeks. Then it updated to built and shipped all at once. That included the spray in bed liner. This was back in late Feb/early Mar. You are close to getting your truck.

That what I think it is. The spay in bed liner seems to make it stay in production for a little longer.
 
  • Like
Reactions: KR3
We typically assume +/- 25% from click type or digital torque wrenches with properly lubricated threads, can achieve about +/- 10% with Hytorque in my experience.

Can you explain this a little more?? Not sure what you are getting to with the different % figures. I do realize that there are often "wet torque" values given for some applications. :unsure: :unsure: :unsure:

:cool::cool::coffee::coffee:🇺🇲🇺🇲🇺🇲🇺🇲
 
Can you explain this a little more?? Not sure what you are getting to with the different % figures. I do realize that there are often "wet torque" values given for some applications. :unsure: :unsure: :unsure:

:cool::cool::coffee::coffee:🇺🇲🇺🇲🇺🇲🇺🇲
Care to explain which applications have "wet torque" values? 🤪
 
Ordered stubby antenna, rear seat latch, OBLink cable, and lug nuts to go with the wheels I've had for 3 months.
Tracker updated today, 6/23 to "In Production" so hopefully we get built and shipped this week! Fingers crossed I'm driving it home in July.

Now gotta decide on what size/brand of tires I want. I've gone back a fourth on multiple sizes for the past 4 months.
 
Last edited:
Can you explain this a little more?? Not sure what you are getting to with the different % figures. I do realize that there are often "wet torque" values given for some applications. :unsure: :unsure: :unsure:

:cool::cool::coffee::coffee:🇺🇲🇺🇲🇺🇲🇺🇲
If target torque is 100 ft.lbs, with normal click type torque wrench we'd expect to see actual torque values applied to be between 75 ft.lbs to 125 ft.lbs with the accuracy range of +/- 25%. Torque Test channel on Youtube has shown some that are much more accurate than that, even Milwaukee's mid torque has a setting that seemed to be +/- 5%. But our general rule of thumb ended sticking with the +/- 25% so that bolted assemblies always had that tolerance built in, in case the torque wrench isn't calibrated recently, or the mechanic is sloppy with settings.
 
If target torque is 100 ft.lbs, with normal click type torque wrench we'd expect to see actual torque values applied to be between 75 ft.lbs to 125 ft.lbs with the accuracy range of +/- 25%.
That's one cheap torque wrench. 🤣 🤣 🤣 🤣

But our general rule of thumb ended sticking with the +/- 25% so that bolted assemblies always had that tolerance built in, in case the torque wrench isn't calibrated recently, or the mechanic is sloppy with settings.
:oops::oops::oops::oops::oops::oops::oops::oops::oops::oops::oops::unsure::unsure::unsure::unsure::unsure::unsure::unsure::unsure::unsure::unsure::unsure::unsure::unsure::unsure::unsure:
but falls into my forte as a reliability mechanical engineer, that spends most of my time looking at bolted assemblies.

Well...from an aviation guy I hope you aren't selling aviation parts...🤣🤣🤣🤣🤣🤣🤣

:cool::cool:🇺🇲🇺🇲🇺🇲🇺🇲
 
Replaced this junk OEM steering stabilizer. It was failed when I bought the truck (31k). Didnt notice it until I got home but the dealer is 1.5h away and then I forgot about it.

I wanted the Fox ATS + the Tremors require that bracket as well. But good lord have those gotten expensive. $650 with the bracket. Ugh P/N FOX-983-02-252

So I went for the $100 amazon special on the Bilstein stock location for now.

Obv came off of the bushing.. But also super hard to compress, had to put my whole body weight on in. And it didn't extend on its own either. The oil is from my NH Oil clear undercoating.

1782327499571.webp


1782327637364.webp


1782327656271.webp


1782327967088.webp
 
Last edited:
Back
Top Bottom