🛠️ What did you do to your Tremor today? [2026 edition]

View attachment 255138Installed two unrelated things behind back seat:
  1. ARB compressor
  2. ICOM ham radio

View attachment 255139
View attachment 255140View attachment 255141View attachment 255142View attachment 255148

Air compressor:
  • Protected from elements compared with exterior mounting
  • Large diameter, metal-reinforced air hose essentially acts like a small air reservoir
  • Probably overdid the power wires (4awg through passenger floor grommet)
  • Gets hot, so have to drop seat back for heavy use :(
  • Made a DIY 4-tire inflation with flexzilla hose
  • On upfitter switch 5 to run with battery (although should run truck for any serious use)
Radio:
  • Faceplate looks factory up by the upfitters
  • Radio box hidden away behind back seat
  • Antenna bracket screws in behind reverse light (no holes in truck)
  • Home-ran and isolated the power wires to secondary battery (trying to avoid interference)
  • Speaker is under back seat with holes drilled to let sound through, then covered with standard speaker cover.
  • Radio can do 2m and 70cm, plus marine, GMRS, and MURS (although not legal in these bands)
  • No more sunglasses holder :(
  • Not sure 2-way radio is worth it anymore with cell phone reception getting so much better (radio is for hunting, not SHTF)
nice i also have my compressor mounted in the same location as well as my icom. but i dont have that 3D printed part. i managed to velcro mine to the glasses holder so i can close it when not in use and not see any radio. i ran the compressor lines down to an air tank under the truck that feeds quick connect points in the front and rear
20260128_171944.webpScreenshot 2026-05-06 232239.webpScreenshot 2026-05-06 232302.webp
 
Added another trail badge of honor. This one was pretty difficult. Alley's curves are amazing as well as the views. Once you go in there's no backing out hence the trail name: All-In Alley 🤪.

21243.webp
 
I'm actually liking this with the S2 BDs built in.
It's off the shelf and he only makes them for the SD's. I have some clear S2 Pro's underneath. I posted on a thread of an event somewhere a few weeks back, but I was cruising 74 or so down a four lane and had a trailer blowout ahead and two lanes to the right of me only to have a full-tread tire carcass rolling upright across lanes straight at me. The best course for myself and all those around me was to take it head-on just inside my left front head light. The trailguard took it, and I had zero damage to the painted bumper or any of the built in cameras or sensors.

For me, the cost of the trailguard paid for itself right then. As far as the tremor valence goes, I kept that, and plan to notch it out where needed, and remount it back under the trailguard to cover up the body seams to dirt accumulation. The trail guard is a good look and offers real protection short of a serious bumper upgrade. I recommend it.
 
It's off the shelf and he only makes them for the SD's. I have some clear S2 Pro's underneath. I posted on a thread of an event somewhere a few weeks back, but I was cruising 74 or so down a four lane and had a trailer blowout ahead and two lanes to the right of me only to have a full-tread tire carcass rolling upright across lanes straight at me. The best course for myself and all those around me was to take it head-on just inside my left front head light. The trailguard took it, and I had zero damage to the painted bumper or any of the built in cameras or sensors.

For me, the cost of the trailguard paid for itself right then. As far as the tremor valence goes, I kept that, and plan to notch it out where needed, and remount it back under the trailguard to cover up the body seams to dirt accumulation. The trail guard is a good look and offers real protection short of a serious bumper upgrade. I recommend it.
Makes total sense and great to know. I'l just a bit confused on the options they offer since they don't show pics of what the first two options are in the drop down. I plan to cal them when they open this morning to discuss. I'd like the light cut outs but not get the lights from them if that's possible.
 
You're much better off getting your own lights direct from someone else. Get exactly what you want that way. I wanted the clear pro's and it really delayed my order.

They have some pretty good pictures of the options throughout the web site, but honestly, you're better off with the full guard with the little bar across the front just above with the morse code on it. It gives you a real solid spot to mount a front license plate with 1/4-20's if you're traveling where you need one, and quick removal when you're not. I have the factory Warn on there like 6.7TremorDubai , but with a 55 hook on it. Looks like he has the intermediate option without the skid plate, so whatever ID on front he has is kind of tucked around. They're a real small outfit, so if you call, it's voicemail and a call back in a day or two. They're local for me, so I went there for the install that he and his boy did for no charge.

This was my truck coming off their lift

 
Last edited:
It's off the shelf and he only makes them for the SD's. I have some clear S2 Pro's underneath. I posted on a thread of an event somewhere a few weeks back, but I was cruising 74 or so down a four lane and had a trailer blowout ahead and two lanes to the right of me only to have a full-tread tire carcass rolling upright across lanes straight at me. The best course for myself and all those around me was to take it head-on just inside my left front head light. The trailguard took it, and I had zero damage to the painted bumper or any of the built in cameras or sensors.

For me, the cost of the trailguard paid for itself right then. As far as the tremor valence goes, I kept that, and plan to notch it out where needed, and remount it back under the trailguard to cover up the body seams to dirt accumulation. The trail guard is a good look and offers real protection short of a serious bumper upgrade. I recommend it.
Thanks for posting your experience. That is encouraging.

I have purchased one as well for my truck 2 months back after seeing a few people purchasing and installing it. I have not installed it yet but will do it when I install my OEM winch along with the BC fog lights that I purchased. I like your idea of also reusing the valence and cutting it where needed to make it work.
 
I'm tired of giving people the ok so I bought a 3D printed hand giving automatic acknowledgement.

21250.webp
 
paid it off today!! (now just got to wait for the title to come in the mail)
also -- I've ordered a lot from PMF Suspension a few weeks back, that just shipped and should be here soon.
Finally decided and ordered my wheels and tires today too:
KMC Impact FFT - Gloss Back - 18x9 0 mm offset
38x11.5x18 Nitto Ridge Grapplers
IMG_0500.webp

PMF's suspension stuff arrived yesterday. I think the total pallet weight was 550 lbs. Roughly looks like end of May is when everything will be here and go on the truck (still waiting on wheels and tires). Felt like Christmas Morning!
 
You're much better off getting your own lights direct from someone else. Get exactly what you want that way. I wanted the clear pro's and it really delayed my order.

They have some pretty good pictures of the options throughout the web site, but honestly, you're better off with the full guard with the little bar across the front just above with the morse code on it. It gives you a real solid spot to mount a front license plate with 1/4-20's if you're traveling where you need one, and quick removal when you're not. I have the factory Warn on there like 6.7TremorDubai , but with a 55 hook on it. Looks like he has the intermediate option without the skid plate, so whatever ID on front he has is kind of tucked around. They're a real small outfit, so if you call, it's voicemail and a call back in a day or two. They're local for me, so I went there for the install that he and his boy did for no charge.

This was my truck coming off their lift

I do like the look myself. My plate is a little bent due to offloading previously before installing the guard so the sand dunes would often rip my lower plastic valance and push my plate. So now the front bumper is much more protected. My only gripe is the poor communication from the company. My order was left for over a month before several calls to the owner to light a fire. Seemingly a common experience with some others. In the end its a solid unit
 
Installed the April group buy. I had a set of S2s already. Added Legmar's bracket and another set of S2s. Fit and finish is top notch.
Wifey wasnt to happy this morning when I told her I had to work on the truck 2 hrs before a wedding we had to go to. Lol I told her the truck wouldn't drive right without them. 🤣 I wish I would have taken a picture of her death glare.
 

Attachments

  • 20260509_093035.webp
    20260509_093035.webp
    281.5 KB · Views: 42
  • 20260509_093026.webp
    20260509_093026.webp
    214.5 KB · Views: 41
Back
Top Bottom