🛠️ What did you do to your Tremor today? [2026 edition]

Installed my new bak revolver. Well, the cover is new, the rails are like new. I purchased it from a fellow member. It was warranted so they sent him a new one. Meanwhile, he bought a diamondback for his rig. He offered to meet me halfway, which was awesome. Thank you @FatherofOne! See y'all at Talladega!
 

Attachments

  • IMG_8303.webp
    IMG_8303.webp
    501.5 KB · Views: 38
Trailer TPMS installed and scaled the trailer. (No water, gas, beer, food, tools, and other camping stuff but a decent base weight. BW Continuum at 2,000 psi.)
IMG_4944.webp
IMG_4946.webp
IMG_4945.webp
IMG_4947.webp
 
It’s a fun color. I had actually considered either purple or true blue back in ‘01 but instead bought my pearl blue Ram. This kind of bridges the gap
 
Pusher Coolant Re-Route Kit and Fleece Under-Bed Fuel Filter with heater and clear bowl.

The HO still has the coolant lines to the turbo running over top of everything. Anyone seen any alternatives to dress those up or re-route them in a less obtrusive manner?
 
ramv


I like that tire temp is also displayed. 🏁

At first, I wouldn't know what to do with that info that psi could not already tell me (low pressure, more heat), but I could begin the extrapolation process.

😝
 
I’ve carried an infrared thermometer and checked sidewall and hub temperatures (and brake temperature on the trucks) for over 20 years so it’s nice to have it realtime. (Typically trailer brakes get to around 200-250 degrees in heavy braking and front truck brakes can hit 1,300+; tire temperatures over 150 start getting concerning)
 
I’m a nerd. And have also rebuilt trailer hubs (including mid trip) and had too many trailer blowouts. My most exciting (my fault) was the emergency brake controller shorted out to the frame, locking the brakes. In the Eisenhower tunnel. The 6.0 PSD was pulling some serious boost to drag the 15klb trailer out to the semi chain check area. Shortly before we exited the tunnel the trailer battery drained and the brakes released.

My other fun one was smoking a major drop off with the trailer avoiding a bear in Yellowstone. I drove to Canada and discovered my wheel bearings were broken so I had to rebuild the hub in a parking lot before coming back.
 
I’ve carried an infrared thermometer and checked sidewall and hub temperatures (and brake temperature on the trucks) for over 20 years so it’s nice to have it realtime. (Typically trailer brakes get to around 200-250 degrees in heavy braking and front truck brakes can hit 1,300+; tire temperatures over 150 start getting concerning)
Yessir! Every time I get fuel on a trip, I break out the IR temp gun. One time on the way to Daytona for a race, one hub was 30* warmer. I swapped in a new hub drum (because I keep a loaded hub in storage) and kept on going. After pulling and inspecting the bearings from the original I found roller bearing galling. I’m convinced there would have been a failure at the worst possible time.
 
At first, I wouldn't know what to do with that info that psi could not already tell me (low pressure, more heat), but I could begin the extrapolation process.
Low pressure does cause high temp, but I had a high temp with normal pressure last year. This happens when you have internal belt separation. It was pretty scary because the tire would have blown for sure had I not pulled over. The tire looked like a balloon ready to pop.
 
Trailers are a PITA but having a rod go through the block on a 7.3 PSD wasn’t great either.
 
Pusher Coolant Re-Route Kit and Fleece Under-Bed Fuel Filter with heater and clear bowl.

The HO still has the coolant lines to the turbo running over top of everything. Anyone seen any alternatives to dress those up or re-route them in a less obtrusive manner?
How was the fleece install? I’m debating if I want to try to do it in my gravel driveway or not
 
How was the fleece install? I’m debating if I want to try to do it in my gravel driveway or not

Nice and simple. I have an S&B 60 gallon tank which complicated it a bit because of restricted access.

Hardest part is contorting your hand to get up and over the tank to release the quick connect fuel line fittings. Once those are off (there are a total of 4) there is only one other bolt to remove and it is easily accessible. Now that I know the best way to attack the quick connect fittings with the S&B tank, I could repeat the process in less than half an hour.
 
5-tire 5000-mile tire rotation today. 2nd time. First was at 4790 mi, after having my fifth oem Duratrac fitted to a fifth Tremor aluminum road wheel I had just purchased.

IMG_7567.webp




The rotation is known as a "rearward cross" where the front/steer tires are crossed to opposite corners at the rear, and where the rear tires go directly forward to serve as steers.

With a 5-tire deal, the spare becomes the right rear, and the left front goes on vacation on the spare winch to literally hang out for 5000 miles before it goes onto the right rear...

IMG_8999.webp


I figured if I slid the spare from under the truck using cardboard it'd be an easier deal. THEN I remembered my old mechanics' creeper from 40 years ago... boy, howdy! does THAT make this job easier (I won't have this luxury if ever having to use my spare out there in the rest of the world but it's nice to have, here at home for tire rotation maintenance).

Also, what's nice about a 5-tire rotation is that only one corner of the truck needs to be lifted at a time.

IMG_8998.webp


I used my HF Badland Mini 1.5-ton. Truck weighs 7100 lbs. Divided by four, that's an average corner weight of 1775 lbs. A 1.5-ton jack lifts 3000 lbs.



IMG_8991.webp


IMG_8997.webp
 
Back
Top Bottom