🛠️ What did you do to your Tremor today? [2026 edition]

Awesome thank you! Looks really good. Any pics of the actual rim and how the depth is into the wheel? Truck looks tough!
Here ya go!
IMG_4240.webp
 
Last edited:
It ain't much... but i got to test out my new ARB tire deflator and Morflate compressor w/ the 4 tire connector and manifold. Damn, what an awesome setup to have! Especially the deflator, less than 30 seconds to drop 10 psig.

Highly recommend both for the trails!
 
Hell yeah that looks great! Looks like I'll be going -18mm. I wonder what the 6mm would look like with these.

Thank you again my friend!
The 6mm was the offset I was looking at, supposedly it’ll push 12.5” wide out 2” from stock, 2.5” for 13.5”.
 
The 6mm was the offset I was looking at, supposedly it’ll push 12.5” wide out 2” from stock, 2.5” for 13.5”.
I'd like to see what it really looks like especially on a 14.50 tire.
 
Lots of lights added today
IMG_7066.webp


Auxbeam v max 7 inch pods on the bumper and 5” pods as ditch lights
Can’t wait to see the increase in light output tonight once it’s dark out

Update: there’s some “hot spots” but for under $500 for all 4 lights I am blown away by the light output. Just the 4 lights on no headlights
IMG_7067.webp
 
Last edited:
How are you liking the moreflate system? I first used it a few weeks ago on a wheeling trip and had to buy it. Which compressor do you have? With 37s i opted for the Ten Six psi Pro as some say you need 6+ cfm at 30 psig.
 
I have a Maddox compressor from harbor freight. It works pretty good for now but I have the arb brushless twin compressor that I need to install.
 
I'd like to see what it really looks like especially on a 14.50 tire.
Agreed, it’s handy to see first, especially before dropping basically $9000+ for rims and tires and a trophy hitch up here.

Though maybe not that wide here…
 
Began the challenge to get Ford to cover my pax side mirror as it will fold in, but not back out anymore. Shop provided them with all the pictures and their input, so now I wait.

Just ordered 5 Star tune and will get it preloaded with 87 Performance, 93 Performance and 87 Daily Tow modes. Mostly want it to help with the shifting of the 10-speed transmission. Was able to pull the info they needed to preload it using FORScan, so that will save me some time.

In the meantime, while I was in FORScan to pull info, did another round of clearing/resetting the transmission adaptive learning.
Well, it only took 3 rounds and two sets of pictures, but Ford agreed to cover my pax side mirror and I had it swapped out yesterday.

Today, I replaced both batteries after 5 years and a couple months. I just went with a set of standard Interstates from Costco for $273 for the pair.

I received my tuner from 5 Star on Thursday and plan is to load the tune tomorrow or Monday.
 
Great looking truck. Got a few more pics, really like those RT pro’s just not sure on 37” is the suspension stock?
yes, stock suspension
 
Finally got the matching rear Ranch Hand Sport, also powder coated Darkened Bronze to match the King Ranch. Added the Morimoto Backup Light Boost Bar during the install.

IMG_4248.jpg

IMG_4249.jpg

IMG_4251.jpg
 
But how will you get into the bed of the truck without your corner steps??? 🤪

Looks great!
Actually one the reasons I did not automatically do this mod when I did the front. I had to make friends with the tailgate step, which is more of an adventure on a Tremor than my old F150. On a side note, you cannot mount AMP bed steps onto this bumper with modifications and even then I think it would look stupid as the bumper is angled not straight. You need to accept your bed access is through the tailgate step or just climbing in.
 
Back
Top Bottom