🛠️ What did you do to your Tremor today? [2026 edition]

Got my onboard air installed! Went with ARB brushless twin compressor. Its installed to a custom mount in the engine bay on the driver's side battery. This mount specifically works with the gas engines not diesel. I ran all Apex Designs airlines and fittings with their Precision tire inflator and used their Rapid Precision Valve stems on my wheels. I modified the ARB provided wire harness to integrate with the factory upfitter switches.
20260306_085631.webp

This bracket fits in the slot below the battery and bolts onto the battery hold down bracket.
IMG_20260308_074935.webp

To make the wire connections simple I ran the ground wire to the provided factory stud on the negative battery terminal.
20260306_085644.webp

The factory doesn't provide a stud on the driver's side positive terminal so I sourced a 6m clinching stud and added one to the poss side. It was easy to install since the terminal is soft copper. Sourced from www.pemnet.com part number HFH-M6-15ZI
IMG_20260306_085830.webp
IMG_20260306_085835.webp

Then I mounted the ARB provided double fuse and ran an upgraded 6AWG wire from the battery to the double fuse. The kit comes with an 8AWG wire but I upgraded to 6AWG since I chose to connect the power going to the relay for the Baja Designs dual fog pocket Squadron lights in my bumper from this double fuse to keep things clean.
20260306_085720.webp
20260305_115316.webp

Here is the wire diagram I used to trim off the unnecessary wire since I was going directly to my upfitters.
Screenshot_20260303_181128_Chrome.webp

I ran the Apex Designs airline down the frame to both sides of the truck to the factory steps then to their panel mounts.
20260306_085355.webp

20260306_085557.webp

20260305_133924.webp

I am very impressed with the Apex products! They are very well made and easy to work with! They contribute to a fast airup-airdown time and compliment the power of the ARB brushless compressor!
20251208_080036.webp
20260101_133959.webp

Here is my double swing bumper from Expedition One with a custom toolbox from Highway Products shown with the Apex Precision tire inflator mounted to the door. The mount is provided with the inflator.
I would like to thank my friends at Expedition Off-Road Development for creating this compressor mount for me. They were great to work with. This mount will be available soon on their website. If you want to get on their pre-order list they would be happy to add you! The final product will be powder coated black! eodupfitters.com
 
Last edited:
Got my onboard air installed! Went with ARB brushless twin compressor. Its installed to a custom mount in the engine bay on the driver's side battery. This mount is specifically works with the gas engines not diesel. I ran all Apex Designs airlines and fittings with their Precision tire inflator and used their Rapid Precision Valve stems on my wheels. I modified the ARB provided wire harness to integrate with the factory upfitter switches. View attachment 248837
Very interesting!

When this model was released two years ago, people complained it got hot quickly. What could be concerning is the unit becoming hotter in that area due to decreased ventilation. Any reports of this particular set-up causing issues? This is an observation, not a complaint.

It's definitely a space saver and something new to see. Great work!
 
I have one of those in the mail right now. Did you find it necessary to remove the upfitter relay box? Or just jam it over to the side?
Was surprised by how far I was able to pull it up. Made it the easiest upfitter box I’ve dealt with. But yes pull it up and turn it on its side and you have plenty of room. The OTC box is easy to install. I used a heat gun to pull the heat shrink off the up fitter wires so did have to cut those at all.
 
Very interesting!

When this model was released two years ago, people complained it got hot quickly. What could be concerning is the unit becoming hotter in that area due to decreased ventilation. Any reports of this particular set-up causing issues? This is an observation, not a complaint.

It's definitely a space saver and something new to see. Great work!
Not sure how it would make a big impact on ventilation, pretty open area. And it sets next to all the big plugs on the firewall so am not too worried. The positive battery cable is closer to the motor than the box. Not sure but assume it printed in ASA or ABS so should hold up just fine.
 
Was surprised by how far I was able to pull it up. Made it the easiest upfitter box I’ve dealt with. But yes pull it up and turn it on its side and you have plenty of room. The OTC box is easy to install. I used a heat gun to pull the heat shrink off the up fitter wires so did have to cut those at all.
Cool. Excellent idea pulling the nubs off! I was debating on pulling the relay box today but since it’s not necessary….Miller Time!
 
Tremor coils finally on the truck, took advantage of an off weekend for kids’ sports.

5600lbs LAS coils netted almost exactly 1.5” on my FX4 diesel that came with 5200lbs LAM coils (measured just a shade over 41” from wheel arch to pavement after instal, “pre” measurement was 39.5”). Still has about 1.75” of rake… very happy with the results.

Install was super easy, maybe 1hr start to finish, unbolted the top sway bar link (18mm) top shock bolt (21mm) and lower brake line retainer bracket (10mm) and the stock coils basically fell off when I released the jack, new coil needed a small nudge from a pry bar to seat and then reversed all the steps.

Ride is a little more firm, but still plenty compliant driving around town with the stock FX4 shocks still on it. Initial impression I actually prefer it as it feels a little more stable and less boaty when driving over bigger bumps (driveway transitions, speed bumps etc), will see how it handles light chop/expansion joints on the highway when I head to the office tomorrow.

Next up, tires! I had been thinking of staying conservative and going with some 315/70r18’s but with the little bit extra height gained I am now very tempted to copy @Mtnduty and throw on a set of 37x13.5’s

Please excuse the filthy truck and tiny little bicycle tires:
IMG_6483.webp

IMG_6484.webp

IMG_6485.webp
 
Tremor coils finally on the truck, took advantage of an off weekend for kids’ sports.

5600lbs LAS coils netted almost exactly 1.5” on my FX4 diesel that came with 5200lbs LAM coils (measured just a shade over 41” from wheel arch to pavement after instal, “pre” measurement was 39.5”). Still has about 1.75” of rake… very happy with the results.

Install was super easy, maybe 1hr start to finish, unbolted the top sway bar link (18mm) top shock bolt (21mm) and lower brake line retainer bracket (10mm) and the stock coils basically fell off when I released the jack, new coil needed a small nudge from a pry bar to seat and then reversed all the steps.

Ride is a little more firm, but still plenty compliant driving around town with the stock FX4 shocks still on it. Initial impression I actually prefer it as it feels a little more stable and less boaty when driving over bigger bumps (driveway transitions, speed bumps etc), will see how it handles light chop/expansion joints on the highway when I head to the office tomorrow.

Next up, tires! I had been thinking of staying conservative and going with some 315/70r18’s but with the little bit extra height gained I am now very tempted to copy @Mtnduty and throw on a set of 37x13.5’s

Please excuse the filthy truck and tiny little bicycle tires:
View attachment 248875
View attachment 248874
View attachment 248876
Does that limit you on travel since you still have the factory FX4 shocks? I would have guessed that the tremor shocks have a little more extension due to the added length of the coils.
 
Bulletpoint center console RubiGrid, their MagSafe charger, carbon fiber arm, matte. Looks great, seems sturdy. Time will tell.
 

Attachments

  • IMG_8120.webp
    IMG_8120.webp
    201.2 KB · Views: 57
  • IMG_8119.webp
    IMG_8119.webp
    138.8 KB · Views: 57
Does that limit you on travel since you still have the factory FX4 shocks? I would have guessed that the tremor shocks have a little more extension due to the added length of the coils.
I would assume it does. However, I don’t plan to run it like this for very long, and they work fine enough for getting around while I make up my mind whether I want to do something simple like Bilstein 5100’s and have that be “good enough” until I eventually do a full Carli system like I had on my 2021, or spend a bit more and get some Accutune custom 2.0 reservoir shocks or maybe the Fox 2.5 HTOs and run that as a longer term solution.
 
Last edited:
Just dropped nearly $5K on an engine repair to replace leaking upper and lower oil pan seals, 3 months out of the 5 year/ 100,000 mile warranty. 2021 6.7 Powerstroke has just over 42,000 miles on it-way to early for this kind of problem. No help from the dealer interceding with the factory. Not pleased.
 
Just dropped nearly $5K on an engine repair to replace leaking upper and lower oil pan seals, 3 months out of the 5 year/ 100,000 mile warranty. 2021 6.7 Powerstroke has just over 42,000 miles on it-way to early for this kind of problem. No help from the dealer interceding with the factory. Not pleased.
Sad to hear...but you are out of warranty so really not much to complain about. A week to 30 days...maybe...but 3 months...I wouldn't have expected it.
 
Working to install the PPE Tranny pan i purchased a while back. Figured while I've got'r dropped i might as well put in the Suncoast solenoid retainers. However, I forgot to order them so... i'll be putting the stocker back on just to cover her up while i wait. Shipping was $35 for $17 in parts so... hopefully they get here quick!
 
Working to install the PPE Tranny pan i purchased a while back. Figured while I've got'r dropped i might as well put in the Suncoast solenoid retainers. However, I forgot to order them so... i'll be putting the stocker back on just to cover her up while i wait. Shipping was $35 for $17 in parts so... hopefully they get here quick!
Good choice to cover it back up. Should be ok without, but as a former engine builder I don’t leave anything open for the chances. Not worth it! I built a “clean room” (plastic sheet and PVC pipe frame) with HEPA filters to assemble engines because of the doggo. I find dog hair inside the freezer and I’ve never seen him in the freezer. Zero chances taken.
 
Productive week this week.

Changed the oil: Valvoline Premium Blue 15W-40, PPE filter.

Just installed a set of 982# add-a-leafs, as I will be adding a set of ADAPT topside boxes and rack to hold all my tools. Ordered an ARB brushless compressor, 20gal tank and Apex CRS. The compressor and tank will be secured to a Builtright bulkhead mount with the feet of the tank resting on the floor of the bed but strapped in.

I'm building my truck to be my mobile mechanic workshop.
 

Attachments

  • 20260308_193545.webp
    20260308_193545.webp
    297.9 KB · Views: 34
Washed it and picked up a Bulletproof hitch off Facebook Marketplace. A buddy of mine has one of these on his 22 F250 and it allows the tailgate to open when hooked up to a trailer where the B&W hitch is just a bit too short (story of my life)
IMG_5814.webp
IMG_5819.webp
 
Back
Top Bottom