🛠️ What did you do to your Tremor today? [2026 edition]

Banks iDash installed, linked to Pedal Monster, First step disconnect both batteries' negative terminals, safety step as the there is an airbag in the A Pillar.
Prep Work:
Not being able to stand the black dash pod used ColorBond Ford Light Graphite and Adhesive Promoter color matching as best possible the gray interior
  • Used magnetic helping hands to set up pod, in my "paint booth.
  • Rough up the pod with 600grit, wipe down with alcohol removing and sanding dust and grease spray Adhesive Promoter, let dry then light coats of color
  • The color is not a 100% match, it was a close as I could get.
My professional paint booth with pod ready for paint 🤪
View attachment 244889
Painted pod mocked up on A Pillar and A Pillar trim piece
View attachment 244892
A Pillar trim pad will need to be cut in order to have pod fit as flush as possible, used blue tape to protect working surface. Using an X-Acto razor saw makes a very clean cut, finish work done using a Dremel tool sanding drum curves the cut to match the pod's for clean flush fit.
Used provided bit by Banks to drill 16mm hole in A Pillar, single pod mount, 18mm hole for dual pod mount. Used blue tape @16mm on bit, setting correct depth
View attachment 244899
Reassembly:
  • Test fit the A Pillar and pod insuring there is at least 1.5 inches of wiring, 4 pin and 6 pin connectors, past the edge of the pod. This is necessary to have enough slack to connect the iDash.
Note, lesson learned once A Pillar is fully seated it's a tight fit, and you won't be able to pull on the wires to get more slack. Learned this the hard way not having enough slack to connectors, had to unbolt A Pillar adjust the wires then reinstall A Pillar 😓
  • Seat the A Pillar and install the top bolt.
  • Using the provided Allen head screw and Allen wrench - install the pod on the A Pillar.
  • After trial and error and exercise of my 4 letter vocabulary😈, discovered the best method due to the angle of the Allen head to the A Pillar was to seat the allen head on the Allen wrench's ball end. Thread the wires thru the pod, then fully seat the pod on the A Pillar, in its final location, which seems to line up the Allen head correctly, then tighten with the wrench.
  • Reconnected batteries, engine running tested iDash and Pedal Monster downloading any firmware updates before buttoning up trim panel and weather stripping
Tie wrap wires as necessary - reinstall trim panel and weather stripping
Finished,
View attachment 244900
View attachment 244901
FWIW, had to look this up, the normal iDash shut down is 30 seconds after the engine is shut down.
Absolutely brilliant my friend! Awesome work and a job well done.

Now drive to Vegas and work on mine 🤪.
 
Great job on mounting.
Optimus .gif
 
Absolutely brilliant my friend! Awesome work and a job well done.

Now drive to Vegas and work on mine 🤪.
You're on make up your wish list - for the Pavement Princess that is 🥳
 
I didnt do anything special. Changed the oil (rotella T6 5w 40), put in new donaldson filter, changed the Fuel Filters (Doc's Diesels), air filter, cabin filter and since it was over 60 today here in Utah I washed my truck as it dearly needed it.
 
A couple days late but I went a picked up a diamond back from @Mtnduty 🤘🤘

I was on the fence about it but he made me a heck of a deal and was local. Put it on and I freaking love it.
 

Attachments

  • IMG_4904.webp
    IMG_4904.webp
    144.5 KB · Views: 40
Those Katskins look good. Nice
 
A couple days late but I went a picked up a diamond back from @Mtnduty 🤘🤘

I was on the fence about it but he made me a heck of a deal and was local. Put it on and I freaking love it.
Looks great man!! It was awesome to meet you, thanks for making the drive.
 
Love it. You doing surgical tubing in the weatherstripping too for full effect?
I'm about to have to do that. I don't mind road noise but when the door keeps making noise randomly depending on crosswinds..... 🤦
I only notice when the "radio" is off, but still 🤣
 
Love it. You doing surgical tubing in the weatherstripping too for full effect?

I will. Probably wait a couple of weeks though, as this took a day and a half and I really did not enjoy fishing the tubing through the weatherstripping on my ‘22..
 
Took advantage of a dry day and got the light locks installed. Very easy installation took my slow ass about and hour total.
IMG_1171.webp
IMG_1176.webp
IMG_1179.webp
 
Following a super-vee this morning, heard a thunk//crack. Thought I put a rock through my grill again. Got the mud cleaned off, so I could check out if anything was broken.

Nothing on the grill. Phew. Nothing visible. Thought I was in the clear. Went to knock some mud of the running boards, and noticed the little half shield on my fuel tank was hanging down. Cracked right down the middle. Anyone happen to know if the highlighted part below has a number?

1770765169836.webp


Or am I going to be forced to put in an S&B? ;-)
 
Met up with local Tremorites for a secret, short notice meet. Can't discuss details but I what I can tell you is that it was Area 51 related 🤪

Thanks to @cntyguy @LVTREMORFTW @04sshd @majorbison @DKM and @TMartinLVNV for attending the time sensitive operation.

@cntyguy had to protect his California presence with the killer Ranch Hand grille guard:

1000031196.webp

1000031170.webp


@LVTREMORFTW always has the cleanest truck!

1000031161.webp
1000031160.webp

1000031199.webp


@majorbison flexing the new Carli Pathfinder set-up and @OmahaBravo security features. Looking good brother!



1000031177.webp

1000031176.webp

1000031184.webp


1000031182.webp


@DKM rolling up with the One Up Offroad kit on INNOV8 wheels:

1000031168.webp

1000031200.webp


@04sshd gave members a demo of the Wolfbox rearview mirror. @cntyguy tried to steal it but he new better!



1000031191.webp
1000031190.webp

1000031169.webp


And some airplane shots:

1000031171.webp
1000031147.webp

Now this is what I call airplane mode! 🤪



Thank you brothers for showing up! Next time I'll bring the Tremor plane 🤪.

Autobots, roll out!

P.S. For security reasons, I did not include @TMartinLVNV's Tacoma 😁. Hope you get your truck next month brother and when you do, let us know! Thank you for showing up. If you have any questions, just ask anyone besides me!
 
Last edited:
Back
Top Bottom