🛠️ What did you do to your Tremor today? [2026 edition]

Wonder if they located the driver yet.
 
Reminds me of of college. Drunk sorority girl parked her car in the living room of another sororities house and took off on foot. Criminal mastermind was located later that evening behind a hedge.
 
I do like the ground setup on yours. I am effectively out of room with my battery having two 2 gage wires (winch, rear winch) and my rear lights, and rear winch solenoid. The latter two I should ground to the chassis. I am doing the OTC kit soon and adding my M&R light bar, so I will likely redo some of the grounds. I originally thought the solenoid and rear lights would be fine, but there's not much room on the OEM terminal.
We didn't want to add the ground since that's not how the factory solution is wired up. Ours is purely an extension of the factory.
 
Last edited:
Shit.....that's more than $9k of damage from the looks of the hit. Bed needs to be checked, rear cab, frame, rear axle....etc etc etc...:mad::mad::mad::mad::mad::mad::mad::mad:

Me? >>>>2027 Order books open....2027 Tremor CCLB....here we come.

:cool::cool:🇺🇲🇺🇲🇺🇲🇺🇲
 
Dropped it off at dealer for it’s first and very likely only warranty visit at 34kish.

Telematics’ unit throwing three dtcs for antennas, and Ford Pass doesn’t work.
One dtc for drivers seat module
Chrome gone on shifter cap
Persistent intermittent “tailgate ajar” warning
Check to see if the SD lean is within Ford spec

We’ll see how it goes. A bit encouraged that my truck is modified out the wazoo and service department didn’t bat an eye about it.
 
Finished up the lift on my new '26 6.7 HO

Basics:
3.5" lift - Front
1.25" lift - Rear
4 Link Front
37x13.50R20 Toyo's
 

Attachments

  • IMG_1430.webp
    IMG_1430.webp
    443.1 KB · Views: 75
Installed a new Sway Bar.
Easy Job to do, didn't even take the time to jack the truck up before doing the install

PN's etc at MVI's F350 Build

1789557858654.webp
 
Last edited:
Dropped it off at dealer for it’s first and very likely only warranty visit at 34kish.

Telematics’ unit throwing three dtcs for antennas, and Ford Pass doesn’t work.
One dtc for drivers seat module
Chrome gone on shifter cap
Persistent intermittent “tailgate ajar” warning
Check to see if the SD lean is within Ford spec

We’ll see how it goes. A bit encouraged that my truck is modified out the wazoo and service department didn’t bat an eye about it.
I get the tailgate ajar warning all the time. Drives me nuts!
 
Installed a new Sway Bar.
Easy Job to do, didn't even take the time to jack the truck up before doing the install

PN's etc at MVI's F350 Build

View attachment 270107
Sounds like yours went on easier than mine. I found it a PITA to get the arms started on the splines on the bar despite the instructions comment of "the arms should go on relatively easily". I know another member on here shared my experience. Rest of it was simple bolt on.
 
The Trick is to use a cold chisel, gently tap that into the the Carli arm and spread the splined section open an additional 0.005"-0.015",
Then the splines slip together easily. Remove the chisel and carry on.
1789568557678.webp


1789568335381.webp
 
Last edited:
I know another member on here shared my experience.


That was I. My solution in addition to the dead blow hammer (as per their instructions) was my idea of heating the splined female end of the black wrinkle finish lever arm by soaking it for a minute or two in hot water.

With a little anti-sieze on the male splines she crawled right on! with little effort. Bingo.

🏁
 
Did your lever arm wrinkle up in the female spline from a dead blow like @Apples? 🤪


No, I did not resort to the Donkey Punch. :ROFLMAO:

As noted, I drew her a hot bath.

And had Teddy Pendergrass singin' "Turn Off The Lights" on the stereo.

😝
 
Back
Top Bottom