🛠️ What did you do to your Tremor today? [2026 edition]

I need to watch a few install videos so I can figure this out. $125 is huge mark-up for less than $10-15 in parts and assembly labor.
Totally agree my friend. Interested to see what you come up with. May take purchasing one and reverse engineering it.
 
I just looked at the connector pin out.
3 minutes in my truck with a test light and I could build this harness.
I even have the connectors in stock. Guess I know what I am building tonight!
PM me once you have it available!
 
When will the strobe kits be coming out? @NEOHIO 😁
Strobes are outside of my comfort zone. I am sure I could figure it out, I have enough on my plate now.
I need to finish writing install instructions on my base harnesses. Photograph and upload 3 or 4 new harnesses I have been sitting on for a few months, as well as install instructions for those as well.
Not to mention still trying to organize my workbench and office to help build stuff for efficiently.
 
Totally agree my friend. Interested to see what you come up with. May take purchasing one and reverse engineering it.
No reverse engineering needed.
The 12 pin connector has 2 power "in".
I am sure all that is being done is the fuse (always on 5/6) needs to by in always on underhood.
Then 1(ignition) power "in" is deleted, the 5/6 always on feeds the rest of the panel.

Reverse engineering is always an option, but I think I have it figured out just looking at the connector pin out.
I can repin the factory connector to confirm how it is done, may not really need a harness at all.

I guess the simplicity of the design is why there are no pictures of the harness online anywhere.
 
No reverse engineering needed.
The 12 pin connector has 2 power "in".
I am sure all that is being done is the fuse (always on 5/6) needs to by in always on underhood.
Then 1(ignition) power "in" is deleted, the 5/6 always on feeds the rest of the panel.

Reverse engineering is always an option, but I think I have it figured out just looking at the connector pin out.
I can repin the factory connector to confirm how it is done, may not really need a harness at all.

I guess the simplicity of the design is why there are no pictures of the harness online anywhere.
I was trying to find anything I could regarding that little harness and came up empty. To me, it just looked like two connectors and wires that are, most likely, criss crossed or altered inside the "hidden" section of the harness and knew it was like a $30 retail part at best.
 
I was trying to find anything I could regarding that little harness and came up empty. To me, it just looked like two connectors and wires that are, most likely, criss crossed or altered inside the "hidden" section of the harness and knew it was like a $30 retail part at best.
It is literally a pin-out swap. Harness isn't really needed if the owner doesn't mind moving terminals around.
I don't see limitless as a forum sponsor, so I don't mind offering these, or a "how-to"
 
I have a pin removal tool so if you would send me, or post, the new pin configuration as well as what you would charge to make this simple "harness" that would be awesome. Thank you my friend!
 
Took deleted 22 to dealer for
Wiper arm recall and other updates no issues with wt reduction
 

Attachments

  • IMG_0957.webp
    IMG_0957.webp
    189.6 KB · Views: 36
Took deleted 22 to dealer for
Wiper arm recall and other updates no issues with wt reduction
I got a few recalls I need to do on my 21… kinda don’t want to go in, not becuase of the weight loss. But the fact that I’m at 99,980 and my truck has never been in the shop, other than a mirror stopped folding in (covered under warranty). I feel that is pretty impressive given I run 37’s, tow, haul and beat it up off road.
 
I got a few recalls I need to do on my 21… kinda don’t want to go in, not becuase of the weight loss. But the fact that I’m at 99,980 and my truck has never been in the shop, other than a mirror stopped folding in (covered under warranty). I feel that is pretty impressive given I run 37’s, tow, haul and beat it up off road.
Trust me it was hard for me
We do everything in house
 
First official trail. Got to use 4wd (not really, just used the rear locker to not spin on a few rocky climbs) 2/10 trails on OnX so not exactly tough but some good scenery. Looking for elk. Once we got to the Brewery in town, an elk was grazing on the lawn :unsure:
IMG_5538.webp
IMG_5531.webp
 

Attachments

  • IMG_5537.webp
    IMG_5537.webp
    456.9 KB · Views: 9
Any one had good results with the ppe trans temp bypass ??
Only thing I noticed on my 2025 is down here in land of extreme heat / Florida. Transmission fluid takes longer to warm up with this ppe item,however does not change high temperature of fluid after warm up. Hauling heavy etc.
I hate to put a product down but I feel wasted money. And yes I did change hose clamps with new oem after photo was taken
20260731_193504.webp
 
Took deleted 22 to dealer for
Wiper arm recall and other updates no issues with wt reduction
Uh-oh, the flags are hung incorrectly. Just flip them over so the union is in the upper-left corner. @McE

Love that deleted Double Deuce! Glad there were no problems.
 
  • Love
Reactions: McE
Any one had good results with the ppe trans temp bypass ??
Only thing I noticed on my 2025 is down here in land of extreme heat / Florida. Transmission fluid takes longer to warm up with this ppe item,however does not change high temperature of fluid after warm up. Hauling heavy etc.
I hate to put a product down but I feel wasted money. And yes I did change hose clamps with new oem after photo was taken
View attachment 266634
I do not have one, but I could see the longer warm up time. If the cooler flow is open then trans temp won’t rise until coolant temp does.
So far as top end temp? That is surprising. Maybe there isn’t as much flow restriction as they thought.
 
on a couple of my older trucks, one has the 10 speed and one has the 6 speed.
we deleted the oem transmission cooler completely and installed mishimito transmission coolers, major difference in temp, much lower
i believe on the 10 speed, a 2020 f350 we had to do something in valve body of trans as well
 
on a couple of my older trucks, one has the 10 speed and one has the 6 speed.
we deleted the oem transmission cooler completely and installed mishimito transmission coolers, major difference in temp, much lower
i believe on the 10 speed, a 2020 f350 we had to do something in valve body of trans as well
I’ve shied away from trying to reduce the temps on the Ford transmissions. They were designed and programmed to operate with the oil at a given viscosity for a given temperature.
 
I’ve shied away from trying to reduce the temps on the Ford transmissions. They were designed and programmed to operate with the oil at a given viscosity for a given temperature.
I somewhat agree. Like the temp when NOT hauling heavy 40 ft loaded .The hauling heavy high temps is why I have done the mods on all mine .I have not heard of any having issues, burnt fluid,clutches ,etc from running to cool 😎
 
I have not heard of any having issues, burnt fluid,clutches ,etc from running to cool


That right there is a great point! but remember too that a malfunctioning valvebody, no matter the digital tune/shift map, can cause overly long shift *time* which is one way to fry a clutchpack. Fluid doesn't have to be hot for that to happen, but the fluid will be much hotter as a result!

/trouble


(I gotta get that new valvebody installed! wtf I have it on the shelf. No real issues yet w/ my 10R140. The vb install is a proactive move)
 
Back
Top Bottom