Rear bumper steps perhaps??
That area down the bumper i have covered. I always wanted more light further up, just couldn’t figure out how to solve for it until these narrower nanos hit the market.
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Rear bumper steps perhaps??
Perdónenme mis hermanos mexicanos, pero....
I don't like coffee but I love the smell of it. At first I thought you were being serious and was like man, that's probably a good idea. Then I finished reading your post...Added a coffee flavoured air freshener to my truck today curtesy of a defective lid. Whole cup of coffee into the passenger footwell, luckily the WeatherTech’s stopped a lot of it, but still got into the seals and wire harness channel, where since it’s -25C, froze instantly.
Next time it thaws out in a garage, gonna have some additional cleaning to do.![]()
Head guy? Gross...Perdónenme mis hermanos mexicanos, pero....
That looks Mexican as hell
I feel like my head guy would do this in a friggin second and I actually love it
Not so much the amount of pointless chrome he had on his old 96 f150 though. "Vents" on the quarter panels that went nowhere, every edge that could be accessed had edge guards, etc..... he now has a tame ass '25 suburban![]()
you should sue em !!Added a coffee flavoured air freshener to my truck today curtesy of a defective lid. Whole cup of coffee into the passenger footwell, luckily the WeatherTech’s stopped a lot of it, but still got into the seals and wire harness channel, where since it’s -25C, froze instantly.
Next time it thaws out in a garage, gonna have some additional cleaning to do.![]()
Hey, what happens in vegas....Head guy? Gross...
Hey, what happens in vegas....![]()
Hey, what happens in vegas....![]()
That area down the bumper i have covered. I always wanted more light further up, just couldn’t figure out how to solve for it until these narrower nanos hit the market.
View attachment 243566
I checked for clearance behind the plastic piece, 3 can be placed proportionally without issues.
View attachment 243562
View attachment 243563
That was my first choice. The problem was tilt on the DB edges. These pods have 20 degrees of tilt each way and DB edge angle is 45 degrees, so at best i would have these pods pointed upward at 20 degrees. Not ideal. On the plastic, i can have them pointed straight at zero degrees, acceptable.
What model tailgate light bar do you have? I am looking at the PUTCO models.That area down the bumper i have covered. I always wanted more light further up, just couldn’t figure out how to solve for it until these narrower nanos hit the market.
View attachment 243566
He has the PUTCO. If you get the Sentinel from @F150LEDs, which I have, it's a tad bit longer:What model tailgate light bar do you have? I am looking at the PUTCO models.
I’m not sure which version @Alpoba has.What model tailgate light bar do you have? I am looking at the PUTCO models.
We have a similar one. Can’t recall the brand. It wasn’t cheap. The pup likes to be able to see more stuff and get the AC on him.The center has a mesh section so air can flow through. The mesh section can also be opened by using the zippers on each side of it. That way heating and cooling vents aren’t blocked for that area.
View attachment 242566
View attachment 242567
Anything under 10 F is my practice. Ford recommends 0 F and less.Plugged in the block heater. Probably didn’t need to, but I paid for the damn thing and how often does it hit 8 degrees in Texas.
That’s how it works. Activates your traction control and 4wd. Supposed to use it under 15mph if I remember correctly.Today it was 30F with ice on my truck and raining. I put the truck in Slippery Roads mode. The truck felt sluggish and turning slowly was very jerky. Is that normal?