Tire Pressure

So your saying I'm safe running 50f and 55r with my 1200lb hitch weight of my travel trailer?

Debatable. Depends on what you're calling safe. Will it pop a bead? No.

What it would do, though, is feel a little mushy. Like driving on soft soil, kind of. That might be something you don't notice at all or it might be something you really notice -- depends on the person. But I would definitely air up the rears when you tow.

If you are towing with a WD hitch -- you'll want to consider that and adjust the fronts accordingly, as well.

Lower PSI can translate into increased rollover risk, too.
 
I run the Ridge Grapplers (F) on Method HDs at 45 front and back when empty. Both the wheels and tires are over-rated for this truck and I keep a small laminated card in the truck with a reference table when adding load or towing. Need to update the Axle weights.

1647385641152.png
 
Debatable. Depends on what you're calling safe. Will it pop a bead? No.

What it would do, though, is feel a little mushy. Like driving on soft soil, kind of. That might be something you don't notice at all or it might be something you really notice -- depends on the person. But I would definitely air up the rears when you tow.

If you are towing with a WD hitch -- you'll want to consider that and adjust the fronts accordingly, as well.

Lower PSI can translate into increased rollover risk, too.
I do run weight distribution, Im thinking about going with 60f and 60r and see how it feels. Sticker on my door says 60f and 70r
 
I’m running 50 front and rear & thinking about dropping to 45 F/R
 
Ok couple questions.


I'm heading to NW Arkansas next week and bringing my 30' 8000lb camper. While we are out there I want to drive on some forest roads and maybe do a little wheeling.

Currently the pressures are set at 60/80, however I want to drop it to 60 all around. Do yall think I can leave it that way towing the camper or will I need to air up before I leave the house.

Second question, I'd like to drop the pressures once we get off the beaten path when we get there. Do yall have suggestions on pressures for fire roads etc?
 
My TT is 8000 also - keep the pressure at mid 70s for better mileage and tire life. When I go wheeling I might not not drop it at all or I might go down to 30 or less if it's going to be sandy. If it's only going to be bumpy then 40 is good. Got in some unexpectedly deep sand last year without airing down and almost got stuck.
 
Ok couple questions.


I'm heading to NW Arkansas next week and bringing my 30' 8000lb camper. While we are out there I want to drive on some forest roads and maybe do a little wheeling.

Currently the pressures are set at 60/80, however I want to drop it to 60 all around. Do yall think I can leave it that way towing the camper or will I need to air up before I leave the house.

Second question, I'd like to drop the pressures once we get off the beaten path when we get there. Do yall have suggestions on pressures for fire roads etc?
Listen to @Loshad for quality of life suggestions.

From purely a load bearing/safety standpoint the factory tires can carry more weight than the rear GAWR at 60 PSI so it’s safe. Here’s a document from Toyo that outlines that (the numbers aren’t manufacturer specific):

 
I read all the threads on this, but seems there is no consensus except, stock pressure is too high and different trucks consider different pressure points under inflated. What makes sense to me is that Diesel Trucks need more pressure in front than rear when unloaded. I saw lots of "Im going to try....." and then no real report back on ride and Mpg, or did I fall asleep reading and scrolling 😃?
 
I read all the threads on this, but seems there is no consensus except, stock pressure is too high and different trucks consider different pressure points under inflated. What makes sense to me is that Diesel Trucks need more pressure in front than rear when unloaded. I saw lots of "Im going to try....." and then no real report back on ride and Mpg, or did I fall asleep reading and scrolling 😃?
The only two constants are “if you’re running the truck fully loaded, use the door sticker pressures”, and “the lower the pressure the better the small bump compliance”.

Beyond that it really comes down to your personal use case and preferences. How frequently you tow and/or haul. How heavy. The ride you like. The specific tires you have. Etc.
What makes sense to me is that Diesel Trucks need more pressure in front than rear when unloaded.
Even this is only true if unloaded for you truly means unloaded. Some folks carry weight in the bed at all times, and then add additional weight when towing or hauling. “Unloaded” in their case may still justify the same or higher pressures in the rear.
 
I read all the threads on this, but seems there is no consensus except, stock pressure is too high and different trucks consider different pressure points under inflated. What makes sense to me is that Diesel Trucks need more pressure in front than rear when unloaded. I saw lots of "Im going to try....." and then no real report back on ride and Mpg, or did I fall asleep reading and scrolling 😃?
I run 50psi at all corners but have kept the towing pressure (60/70) this past Fall when there was a short duration between hooking up the TT. I have not measured a significant difference in fuel economy. It is probably within the rounding error. After 8k miles I still notice an improvement in overall ride quality and impact harshness between the two pressure settings.
 
I run 50psi at all corners but have kept the towing pressure (60/70) this past Fall when there was a short duration between hooking up the TT. I have not measured a significant difference in fuel economy. It is probably within the rounding error. After 8k miles I still notice an improvement in overall ride quality and impact harshness between the two pressure settings.
Thank-you, Sir!
 
I posted a load inflation table in another thread. Non diesel is 4100f 3100r. Diesel is about 5100F. Just use that chart to figure out how much psi you need. Add an additional 800lbs to each axle for a safety margin and do the math. You'd be amazed at the ride difference doing from 70lbs to 50.

I run 48F42R unloaded. Carli has a really good write up on their site about tire pressures. Anyone with a tiny bit of interest in this subject would benefit from reading it.

Great read. Thanks for posting. Only concern i have is will the tires wear correctly
 
I run 54 front and 50 rear unloaded with the 7.3. Much less harsh under normal driving and they run cool. When towing my travel trailer I raise the rear to 60. If loading the truck heavily, the fronts and rears go up to 75. This is with about 3,000 lbs in the truck and maybe towing too. Rock hard tires are annoying and unnecessary, but too soft tires are inefficient and run hot. Check the tire temps at fuel stops. Too hot means they need more air. I've also switched to Cooper AT3 in 295/70 R18E on stock wheels. These run silent, are better in soft dirt, have better traction in various highway winter conditions and are overall a better tire. About 1/2" less diameter, and about .6" wider. Plus cheaper than the stock size.
 
I read all the threads on this, but seems there is no consensus except, stock pressure is too high and different trucks consider different pressure points under inflated. What makes sense to me is that Diesel Trucks need more pressure in front than rear when unloaded. I saw lots of "Im going to try....." and then no real report back on ride and Mpg, or did I fall asleep reading and scrolling 😃?
62 cold all 4 tires....then i dont get an underinflation alarm......i also am running mickythompson baja boss 305-70 18s....and thier max psi is 65
 
I read all the threads on this, but seems there is no consensus except, stock pressure is too high and different trucks consider different pressure points under inflated. What makes sense to me is that Diesel Trucks need more pressure in front than rear when unloaded. I saw lots of "Im going to try....." and then no real report back on ride and Mpg, or did I fall asleep reading and scrolling 😃?
I guess I'll also throw in what I'm running. Quoting from my build thread (gas engine on Toyo ATIII's):

I had previously adjusted the rear to be 60 psi, and was running 60 psi all around; however, with my newly acquired scale weights I took a fresh look at my pressures.

End result are these pressures:
  • Daily driving: 50psi front and rear
    • Up to 5000 pounds towing OR
    • Up to 1000 pounds additional weight in bed
  • Light hauling: 50psi front, 60psi rear
    • Up to 7500 pounds towing OR
    • Up to 1500 pounds additional weight in bed
  • Heavy Hauling: 60psi front, 75psi rear (factory specifications)
    • Maximum capacity.
I got there by using the Toyo Load and Inflation guide along with my front and rear GAWR. I worked out that at 50psi with my tires (factory size Toyo's) each tire is able to carry 3000 pounds. This means each axle will be capable of carrying the front GAWR (4800 pounds) with a 25% buffer.

50psi is a nice drop from factory spec, improving ride, but still leaves lots of room for daily life. I have lots of overhead to carry passengers and tow lighter trailers. The buffer accounts for variances; variances in pressures, potentially caused by temperature changes or slow leaks, and variances in loading (e.g. I accidentally overload the front axle a bit).

Without touching the front pressures, I can go up to light hauling. Again, that 50 psi is good for the full front GAWR so there shouldn't be any risk up front, and 60psi in the rear gives me more capacity back there.

Going up to heavy hauling I want to be at factory spec all around. Realistically it should be massive overkill based on the load table, but when hauling those kinds of weights might as well be safe than sorry.

And those scale weights being referred to in the last quote:
After that I was next to a Travel America that has CAT Scales, so I figured I would weigh Shadowfax for the first time. This was with a full tank of gas, my current modifications, and all of the stuff I normally keep in the truck for SAR and general life. I was out of the truck so no humans were weighed. Weights are:
  • Steer axle: 4360 pounds
  • Drive axle: 3860 pounds
  • Gross weight: 8220 pounds
Given my GVWR of 11,300 pounds, that puts my available payload capacity, above and beyond my daily carry, at 3080 pounds. This makes me very pleased. :D
 
Back
Top Bottom