Tire Pressure

Forscan is a reprogramming tool for the trucks computer.

Typically the tire pressure monitor (TPMS) is set at the recommended pressure as it's minimum threshold to activate the light. So on the tremor it would be 60/80.

Did you ask the dealer to lower your tire pressure? Did they also change the threshold for the TPMS in the computer? If they didnt change the value then you will get a low tire light running the rear at 60.
 
Forscan is a reprogramming tool for the trucks computer.

Typically the tire pressure monitor (TPMS) is set at the recommended pressure as it's minimum threshold to activate the light. So on the tremor it would be 60/80.

Did you ask the dealer to lower your tire pressure? Did they also change the threshold for the TPMS in the computer? If they didnt change the value then you will get a low tire light running the rear at 60.
Mike,
I filled the rear tires to 70 and my problem went away. Thanks! Im guessing they came 60ish from the factory?? Who knows. All good now
 
Set front 60 and rear 70
 

Attachments

  • 498EA64F-7529-416C-9612-CDD37DD7149F.webp
    498EA64F-7529-416C-9612-CDD37DD7149F.webp
    232.4 KB · Views: 164
Maybe cooler weather dropped the pressure enough to set them off?
I've been running 55 front and 60 rear
With both tpms set to 60 psi via ForScan
And no issues....as i think it needs to drop 15% below what you set it for before it goes off.
So that would go off at 51 psi when set at 60psi
 
I have 65 psi in the rear tires and never had an issue but today both the rear sensors are saying they are low not sure what’s going on?
Is yours an F350? I thought those were 60 fr/ 80 rr. My F250 is 60/70. If so, and it is relatively cold where you are today, you might have hit the threshold. It is 25% which would put you at 60psi for the alert.
 
So I weighed my 22 tremor with the 7.3. Its 7480 total, 4200 front and 3280 rear. The door sticker says 60f and 70r currently with the cold temps its at 55f and 65r. My question is do you guys tow at the factory spec or do you run a little less if your not maxed out? Im towing a 34’ 8000lb travel trailer.
 
Has anyone made adjustments to the stock tire pressure for a better highway ride? I've seen some guys on facebook drop it from 60/80 to 60/60 unloaded.
I run 60/55. I changed the air pressure trigger point in FORSCAN so I don't have any issue.
 
So I weighed my 22 tremor with the 7.3. Its 7480 total, 4200 front and 3280 rear. The door sticker says 60f and 70r currently with the cold temps its at 55f and 65r. My question is do you guys tow at the factory spec or do you run a little less if your not maxed out? Im towing a 34’ 8000lb travel trailer.
Is that the truck alone or with you sitting in it? Full tank of gas? Thank you.
 
I run 60 in the front and 50 in the rear. I air up the rear if I’m hauling a load. I used forscan to adjust the tpms. I lowered it to 45 psi front and rear so the warning light stays off. Running 70 in the rear with an empty truck is a harsh ride and will flat spot the center of the tires.
 
I took a mathematical approach to the tire pressure. I wanted to find out what formula would apply to how Ford determined the suggested psi based on the GAWR of the front and rear. Here is the formula I used and verified works for my truck using CAT scales and further verified using the "chalk test." (disclaimer: adjust tire pressures at your own risk. I have not verified any of this with any Ford engineers. Your truck configuration may vary. This is based on a 2020 F350 7.3l Gas Tremor with stock Goodyear Duratrac Tires)

Total Recommended Load Rating for both tires combined in lbs = (Measured Axle Load + 4904 lbs.) multiplied by 0.6883

Divide results by 2 and use psi load rating reference chart to determine psi
Tire Pressure Chart for Stock Duratracs
​
Examples:
Front GAWR on my truck is 4,800
(4800 + 4904)0.6883 = 6,679
6,679/2=3,339

According to tire pressure chart, recommended psi is 60 psi (same as Ford recommended psi on door jam sticker)

Rear GAWR on my truck is 6,950
(6950 + 4904)0.6883 = 8159
8159/2=4080

According to tire pressure chart, recommended psi is 80 psi (same as Ford recommended psi on door jam sticker)

Measured rear axle weight on my truck empty from CAT scale with full tank of gas and 1 passenger is 3,520
(3520 + 4904)0.6883 = 5798
5798/2=2899

According to tire pressure chart, recommended psi is 50 psi (round up).

Measured front axle weight rating on my truck empty from CAT scale with full tank of gas and 1 passenger is 4,200
(4200 + 4904)0.6883 = 6266
6266/2=3133

According to tire pressure chart, recommended psi is 55psi (round up)​

Here is the math to how I figured out this equation if you are interested. (may differ from your truck configuration):

Formula:

Total Recommended Load Rating for both tires combined in lbs = (GAWR + x) y

x = increase in lbs (safety factor)
y = percentage of GAWR including safety factor

For my specific truck, the formula resulted in:

Front: 6680 = (4800 +x) y
Rear: 8160= (6950 +x) y

I then solved for y for front:

Front: 6680/(4800+x) = y

Used y from front to solve for x on the rear:

Rear:
8160 = (6950+x)((6680/(4800+x))
8160 = (46,426,000+6680x)/(4800+x)
39,168,000 + 8160x = 46,426,000 + 6680x
1,480x = 7,258,000
x = 4904

Now plug x back in to equation to solve for y (I used the Front equation, but it doesn't matter which one you use):

6680 = (4800 + 4904)y
6680 = 9,704y
0.6883 = y

Final equation to determine tire pressure based on load:

Total Recommended Load Rating for both tires combined in lbs = (Measured Axle Load + 4904 lbs.) multiplied by 0.6883
So your saying I'm safe running 50f and 55r with my 1200lb hitch weight of my travel trailer?
 
So your saying I'm safe running 50f and 55r with my 1200lb hitch weight of my travel trailer?

If you use the equation SilverBullet used: (Assuming your rear axle weight is similar at 3500 lbs)
Total Recommended Load Rating for both tires combined in lbs = (Measured Axle Load + 4904 lbs.) multiplied by 0.6883
Load rating = [(3500+1200)+4904]*0.6883
Load rating = 3305

Then use the duratrack chart:

The chart is pretty linear resulting in this equation:
PSI = 0.0253*(Load Rating) - 23.975
PSI = 60

Disclaimer = I am not an expert here and am just using these charts to the best of my understanding.
 
Back
Top Bottom