Tire Pressure

My first post here. Been learning a bit about the tire pressure monitor system. I'm not liking 80 psi rear tire pressure in my '21 F250 Tremor. Gonna try and lower to 60 to match the fronts and see what kind of alerts I get. Changing the settings w/ FORScan is a nail biter for an old guy like me. Is it easy to do?
 
My first post here. Been learning a bit about the tire pressure monitor system. I'm not liking 80 psi rear tire pressure in my '21 F250 Tremor. Gonna try and lower to 60 to match the fronts and see what kind of alerts I get. Changing the settings w/ FORScan is a nail biter for an old guy like me. Is it easy to do?
80 PSI sucks if you are not loaded heavy. I reduced mine to 71 to try it out and no warning. I think the fronts are a 65.

I don't know what the factory TPMS settings are, but I'd like to lower my warning point to 30 then I could air down off road and avoid the warning.
 
I've been wondering why Ford says 20 more in the rears if you aren't towing or hauling. Seems like the axles are fairly evenly loaded if empty so why not 60-65?
I have had mine set at 65 all around for awhile. The weather turned cool this week and the right rear fell below 60 and the tire light came on. Filled them back up to 65 and drove for a bit. Light went off. I made no changes with 4 scan. So you should be fine near 60 but will have to keep them topped off.

As for them being at 80 in the rear. They have to assume you will be hauling a full load with the vehicle and won't recommend anything lower. I was in the tire industry when the explorer tire recall was happening. They had recommended 29 or was it 26 psi all around and that would have been fine if people actually kept up on their tires. But people didn't and they got dangerously low. This caused problems. If ford recommend an unloaded psi, someone wouldn't change it and they would probably blame ford.
 
I've been wondering why Ford says 20 more in the rears if you aren't towing or hauling. Seems like the axles are fairly evenly loaded if empty so why not 60-65?
I’ve posted a more detailed reply somewhere on the forum (might not be this thread) but the tire pressure settings are based on the axle weight ratings. They can’t recommend anything less than what is required to support the maximum load condition (plus a safety factor).
 
Stock wrangler MTs. Been running 48psi in front and 53 psi cold in the rear for about 5000 miles. They climb about 3 to 4 psi when they warm up. Rides way better. If I am going to go tow the skid steer I air up to about 70 psi. That 80 psi is only if you are going to put max payload in the truck, which I don't intend to do, thats why i have trailers. Yes warning light stays on, about as annoying as remembering to turn off the auto start/stop on the wife's expedition. I believe sensors go off at 55 front and 65 rear from my experience.
 
I posted a load inflation table in another thread. Non diesel is 4100f 3100r. Diesel is about 5100F. Just use that chart to figure out how much psi you need. Add an additional 800lbs to each axle for a safety margin and do the math. You'd be amazed at the ride difference doing from 70lbs to 50.

I run 48F42R unloaded. Carli has a really good write up on their site about tire pressures. Anyone with a tiny bit of interest in this subject would benefit from reading it.

Can you post the load inflation table again? I'm unable to find it.:eek:
 
I'm at 50F 65R and happy with it. No lights. May try to bring the rears down more based on this thread.

Interesting that Carli tunes to 40F 35R on their packages.
 
I took a mathematical approach to the tire pressure. I wanted to find out what formula would apply to how Ford determined the suggested psi based on the GAWR of the front and rear. Here is the formula I used and verified works for my truck using CAT scales and further verified using the "chalk test." (disclaimer: adjust tire pressures at your own risk. I have not verified any of this with any Ford engineers. Your truck configuration may vary. This is based on a 2020 F350 7.3l Gas Tremor with stock Goodyear Duratrac Tires)

Total Recommended Load Rating for both tires combined in lbs = (Measured Axle Load + 4904 lbs.) multiplied by 0.6883

Divide results by 2 and use psi load rating reference chart to determine psi
Tire Pressure Chart for Stock Duratracs
​
Examples:
Front GAWR on my truck is 4,800
(4800 + 4904)0.6883 = 6,679
6,679/2=3,339

According to tire pressure chart, recommended psi is 60 psi (same as Ford recommended psi on door jam sticker)

Rear GAWR on my truck is 6,950
(6950 + 4904)0.6883 = 8159
8159/2=4080

According to tire pressure chart, recommended psi is 80 psi (same as Ford recommended psi on door jam sticker)

Measured rear axle weight on my truck empty from CAT scale with full tank of gas and 1 passenger is 3,520
(3520 + 4904)0.6883 = 5798
5798/2=2899

According to tire pressure chart, recommended psi is 50 psi (round up).

Measured front axle weight rating on my truck empty from CAT scale with full tank of gas and 1 passenger is 4,200
(4200 + 4904)0.6883 = 6266
6266/2=3133

According to tire pressure chart, recommended psi is 55psi (round up)​

Here is the math to how I figured out this equation if you are interested. (may differ from your truck configuration):

Formula:

Total Recommended Load Rating for both tires combined in lbs = (GAWR + x) y

x = increase in lbs (safety factor)
y = percentage of GAWR including safety factor

For my specific truck, the formula resulted in:

Front: 6680 = (4800 +x) y
Rear: 8160= (6950 +x) y

I then solved for y for front:

Front: 6680/(4800+x) = y

Used y from front to solve for x on the rear:

Rear:
8160 = (6950+x)((6680/(4800+x))
8160 = (46,426,000+6680x)/(4800+x)
39,168,000 + 8160x = 46,426,000 + 6680x
1,480x = 7,258,000
x = 4904

Now plug x back in to equation to solve for y (I used the Front equation, but it doesn't matter which one you use):

6680 = (4800 + 4904)y
6680 = 9,704y
0.6883 = y

Final equation to determine tire pressure based on load:

Total Recommended Load Rating for both tires combined in lbs = (Measured Axle Load + 4904 lbs.) multiplied by 0.6883
 
When I bought my truck dealer had 65 in front and 86 rear. I’m currently running 60f 74r. I will probably go 60/60 and air up rear if I tow heavy
 
I took a mathematical approach to the tire pressure. I wanted to find out what formula would apply to how Ford determined the suggested psi based on the GAWR of the front and rear. Here is the formula I used and verified works for my truck using CAT scales and further verified using the "chalk test." (disclaimer: adjust tire pressures at your own risk. I have not verified any of this with any Ford engineers. Your truck configuration may vary. This is based on a 2020 F350 7.3l Gas Tremor with stock Goodyear Duratrac Tires)

Total Recommended Load Rating for both tires combined in lbs = (Measured Axle Load + 4904 lbs.) multiplied by 0.6883

Divide results by 2 and use psi load rating reference chart to determine psi
Tire Pressure Chart for Stock Duratracs
​
Examples:
Front GAWR on my truck is 4,800
(4800 + 4904)0.6883 = 6,679
6,679/2=3,339

According to tire pressure chart, recommended psi is 60 psi (same as Ford recommended psi on door jam sticker)

Rear GAWR on my truck is 6,950
(6950 + 4904)0.6883 = 8159
8159/2=4080

According to tire pressure chart, recommended psi is 80 psi (same as Ford recommended psi on door jam sticker)

Measured rear axle weight on my truck empty from CAT scale with full tank of gas and 1 passenger is 3,520
(3520 + 4904)0.6883 = 5798
5798/2=2899

According to tire pressure chart, recommended psi is 50 psi (round up).

Measured front axle weight rating on my truck empty from CAT scale with full tank of gas and 1 passenger is 4,200
(4200 + 4904)0.6883 = 6266
6266/2=3133

According to tire pressure chart, recommended psi is 55psi (round up)​

Here is the math to how I figured out this equation if you are interested. (may differ from your truck configuration):

Formula:

Total Recommended Load Rating for both tires combined in lbs = (GAWR + x) y

x = increase in lbs (safety factor)
y = percentage of GAWR including safety factor

For my specific truck, the formula resulted in:

Front: 6680 = (4800 +x) y
Rear: 8160= (6950 +x) y

I then solved for y for front:

Front: 6680/(4800+x) = y

Used y from front to solve for x on the rear:

Rear:
8160 = (6950+x)((6680/(4800+x))
8160 = (46,426,000+6680x)/(4800+x)
39,168,000 + 8160x = 46,426,000 + 6680x
1,480x = 7,258,000
x = 4904

Now plug x back in to equation to solve for y (I used the Front equation, but it doesn't matter which one you use):

6680 = (4800 + 4904)y
6680 = 9,704y
0.6883 = y

Final equation to determine tire pressure based on load:

Total Recommended Load Rating for both tires combined in lbs = (Measured Axle Load + 4904 lbs.) multiplied by 0.6883
Thank you for your research in this.
 
I've only 430 miles so far running 60/70. Tires feeling less squirrelly the last hundred miles so I think I will go down to 55/65 in a couple hundred. They're pretty darn good right now but should be better at 55/65. Will be towing in 10 days so will try 65/75 then.
 
Tire pressure question. Picked my truck up today from the dealer. 1/2 way home on my first drive tps lights up. Driver rear left 54, all others 60. Got home and filled back left up to 60. Drive home and turned off. Light is still on?? Any ideas on how to remove light? Thanks 🙏
 

Attachments

  • A5AA5CE7-72DE-4852-8E76-8473AF3E0A33.webp
    A5AA5CE7-72DE-4852-8E76-8473AF3E0A33.webp
    90.1 KB · Views: 65
  • 0A7FF186-4C94-406C-B896-7436E722D923.webp
    0A7FF186-4C94-406C-B896-7436E722D923.webp
    86.7 KB · Views: 66
Tire pressure question. Picked my truck up today from the dealer. 1/2 way home on my first drive tps lights up. Driver rear left 54, all others 60. Got home and filled back left up to 60. Drive home and turned off. Light is still on?? Any ideas on how to remove light? Thanks 🙏
Did you adjust the minimum threshold with forscan and what is it set at. It takes some time for it to register the new pressure and the light to go off. I would drive it for 10-15 minutes.
 
Did you adjust the minimum threshold with forscan and what is it set at. It takes some time for it to register the new pressure and the light to go off. I would driv
Did you adjust the minimum threshold with forscan and what is it set at. It takes some time for it to register the new pressure and the light to go off. I would drive it for 10-15 minutes.
I’m not familiar with forscan. Just drove truck home today
 
Back
Top Bottom