Aftermarket Wheels & Tire size/offset photos

do you know what was done?
I have just have Carli caster shims

with the duratracs is drove straight.
Sorry - don't know what was done other than align it to OEM spec tollerances - CJC did the work, they also did install of Carli system and the wheels and tires.
 
Sorry - don't know what was done other than align it to OEM spec tollerances - CJC did the work, they also did install of Carli system and the wheels and tires.
Did you have both steering stabilizers installed or just one? They are designed to work together in opposing force. If you have just one, you may need to adjust the pressure to compensate for the pull to the left.

From Carli's site:

2017-21 Super Duty:​

Same as 2008-16 but the high mount runs a short rod-end at the drag link bracket.

  • Low Mount Steering Stabilizer: Carli Differential Guard and tie-rod clamp provide mounting provision for this stabilizer. A higher nitrogen charge pushes to the Right to counter-act a Left Hand Tire Pull.
  • High Mount Steering Stabilizer: Installs up and out of the way with the provided frame hardware and Drag-Link Bracket. A higher nitrogen charge pushes to the left to counter-act a Right Hand Tire Pull. Combine with a Carli Low-Mount for a true, infinitely adjustable stabilization system for optimal damping with any tire.
 
Did you have both steering stabilizers installed or just one? They are designed to work together in opposing force. If you have just one, you may need to adjust the pressure to compensate for the pull to the left.

From Carli's site:

2017-21 Super Duty:​

Same as 2008-16 but the high mount runs a short rod-end at the drag link bracket.

  • Low Mount Steering Stabilizer: Carli Differential Guard and tie-rod clamp provide mounting provision for this stabilizer. A higher nitrogen charge pushes to the Right to counter-act a Left Hand Tire Pull.
  • High Mount Steering Stabilizer: Installs up and out of the way with the provided frame hardware and Drag-Link Bracket. A higher nitrogen charge pushes to the left to counter-act a Right Hand Tire Pull. Combine with a Carli Low-Mount for a true, infinitely adjustable stabilization system for optimal damping with any tire.

I have both low and high mount on my truck.
 
Last edited:
I just have the factory stabilizer for now. The more I drive it, it seems like the pull might actually be mostly the tires running in the groves of the pavement. they are wider and the truck has a wider stance now. sometimes it drives straight as an arrow, others it pulls/drifts to the left. 🤷🏻‍♂️
 
I’ve been all over the place with wheels for a year now and finally went ahead with a polished 20x10 American Force Independence, I almost exclusively run Toyo M/Ts but I’m considering the R/T this time, we’ll see. either way, I’m gonna do a Wicked 2.5” level with Fox 2.0 reservoir shocks.
 
Last edited:
I’ve been all over the place with wheels for a year now and finally went ahead with a polished 20x10 American Force Independence, I almost exclusively run Toyo M/Ts but I’m considering the R/T this time, we’ll see. either way, I’m gonna do a Wicked 2.5” level with Fox 2.0 reservoir shocks.
There are a few youtube comparisons showing db levels are roughly the same. So if your looking at RT's for less noise, I'd say it's almost not worth it. I have the 37x12.50x18 and they look skinny. The MT's will look a lot better with very minimal noise increase over the RT's.
 
There are a few youtube comparisons showing db levels are roughly the same. So if your looking at RT's for less noise, I'd say it's almost not worth it. I have the 37x12.50x18 and they look skinny. The MT's will look a lot better with very minimal noise increase over the RT's.
I’ve had both of them and the noise with the M/T has never been noticeable even on a 38x13.50, I was just thinking of giving the R/T another try to see if there’s actually any difference in the snow but I pretty much always end up replacing anything else I try with the M/T anyway
 
I don’t care about noise, looking for a winter rated aggressive all terrain tire if such exists in 35”
 
I don’t care about noise, looking for a winter rated aggressive all terrain tire if such exists in 35”
Toyo AT III is a 3 peak snowflake rated tire and they make them in 35 and 37. 35's come in load range D or F (you want F for Superduty) and their 37's are load range E. Referenceing 35 x 12.5 x 18 or 37 x 12.5 x 18 - they have many other sizes as well. I run the 37x12.5x18 on mine and am very happy with them.

Link 35: https://www.tirerack.com/tires/tires.jsp?tireMake=Toyo&tireModel=Open+Country+A/T+III&sidewall=Blackwall&partnum=525QR8OCAT3&tab=Sizes

Link 37: https://www.tirerack.com/tires/tires.jsp?tireMake=Toyo&tireModel=Open+Country+A/T+III&partnum=725QR8OCAT3&vehicleSearch=false&fromCompare1=yes
 
Toyo AT III is a 3 peak snowflake rated tire and they make them in 35 and 37. 35's come in load range D or F (you want F for Superduty) and their 37's are load range E. Referenceing 35 x 12.5 x 18 or 37 x 12.5 x 18 - they have many other sizes as well. I run the 37x12.5x18 on mine and am very happy with them.

Link 35: https://www.tirerack.com/tires/tires.jsp?tireMake=Toyo&tireModel=Open+Country+A/T+III&sidewall=Blackwall&partnum=525QR8OCAT3&tab=Sizes

Link 37: https://www.tirerack.com/tires/tires.jsp?tireMake=Toyo&tireModel=Open+Country+A/T+III&partnum=725QR8OCAT3&vehicleSearch=false&fromCompare1=yes

Have never known anybody to run these tires but will definitely check them out

I’ve been planning on going with 17!inch wheels as that’s what Carli recommends
 
Finally got around this evening to installing some 22x12’s with Cooper STT Pro 325/50’s (35x13.50).

Little rub at full lock on the plastic mud flaps, but a heat gun took care of that. Would definitely have plenty of clearance without any prefit mud flaps. No other clearance issues.

Running 3.5” lift in front and .75” in back.

I have some Rokblokz mud flaps, but haven’t had a chance to install them yet.

Center caps are not installed in those photos…
 

Attachments

  • 0032062D-CF9C-4BD3-A573-12DF4966F196.webp
    0032062D-CF9C-4BD3-A573-12DF4966F196.webp
    271 KB · Views: 528
  • A519C57E-C503-4DA6-AB81-06D080517053.webp
    A519C57E-C503-4DA6-AB81-06D080517053.webp
    245.5 KB · Views: 523
  • FE4967A1-B80F-4D73-BE31-9005BB795E33.webp
    FE4967A1-B80F-4D73-BE31-9005BB795E33.webp
    93.6 KB · Views: 522
I am running a similar setup to you JCKustoms. How much clearance do you have on your fenders? I need to come up with a mud flap of some kind for the front and would be interested to see how much clearance you have.
 

Attachments

  • 1.webp
    1.webp
    79.4 KB · Views: 95
I am running a similar setup to you JCKustoms. How much clearance do you have on your fenders? I need to come up with a mud flap of some kind for the front and would be interested to see how much clearance you have.
The pic below shows the gap I have with wheels at neutral. It’s approximately 4.25” at the closest point. My wheels are 22x12. 22x10’s would have plenty of clearance with the 325/50R22’s.

I installed the RokBlokz mud flaps and the tires do contact the flaps at full lock, but just barely rub.
 

Attachments

  • image.webp
    image.webp
    133.1 KB · Views: 85
Little bit different type of build on this one. Keeping it sporty and practical for daily driving as a work truck and going for flush figment so I’m not kicking debits and tire shine all over. 20x9 American forces 0 offset. 295/65/r20s Toyo open country at3s. Filled out wheel wells slight poke <1/2”
 

Attachments

  • 2789C4FD-8389-44AC-B305-97914372BCCD.webp
    2789C4FD-8389-44AC-B305-97914372BCCD.webp
    46.5 KB · Views: 295
  • F336D4C0-F6E1-40F5-AFE6-B1906BDAB3C9.webp
    F336D4C0-F6E1-40F5-AFE6-B1906BDAB3C9.webp
    121.6 KB · Views: 229
  • C6E1B673-1933-4548-A5B2-0635E5A7B05A.webp
    C6E1B673-1933-4548-A5B2-0635E5A7B05A.webp
    90.4 KB · Views: 292
  • B44D62EA-0AE6-4EAC-8212-2F7CBCFDE707.webp
    B44D62EA-0AE6-4EAC-8212-2F7CBCFDE707.webp
    251.1 KB · Views: 289
Little bit different type of build on this one. Keeping it sporty and practical for daily driving as a work truck and going for flush figment so I’m not kicking debits and tire shine all over. 20x9 American forces 0 offset. 295/65/r20s Toyo open country at3s. Filled out wheel wells slight poke <1/2”
Also no lift all stock. Aired the tires down to 60 in front 55 in rear seems like sweet spot for reg driving with no payload and hood tire wear. Tires seem pretty square to road for nice wearing no humps
 
Also no lift all stock. Aired the tires down to 60 in front 55 in rear seems like sweet spot for reg driving with no payload and hood tire wear. Tires seem pretty square to road for nice wearing no humps
You have to do any trimming to make 20s fit?
 
You have to do any trimming to make 20s fit?
No. Everything fit nice no rubbing.
What I will say is I was surprised when you look at the calculators for stock tire size to this tire size shows a difference of less than 1/2” in height. When I got them theyre about a full inch taller but I didn’t measure with a tape
 
Anyone with positive 14-20 offset paired with 12.5 x18? Think this is the way I’m going. The 0 offset look to stick out a bit more than I want. I like the stock wheel and tire set up but the tucked in look I can’t do personally.
I was surprised how far the 0 stuck out as well. If you find that setup let me know. I only seem to find 0 or -18 in ones I ilke. I had fuel podiums that were plus 20 in 18s but doesn't look like they make them anymore.
 
Back
Top Bottom