22 Black Bear 🐻 Build

Had Brian at No Sweat Window Tint in Kerville, TX give my truck the SunTek ceramic treatment yesterday. He’s a fantastic guy. I would absolutely use him again for any vehicle or my home.

Clear tint on windshield. Brow to AS1 line.
Clear tint on sunroof (for heat reduction).
Legal limit on front doors.
Limo tint on rear doors and back glass.

No Sweat Window Tinting
(830) 367-4563

Before:
View attachment 143698

After:
View attachment 143699View attachment 143700View attachment 143701View attachment 143702
Looks awesome my friend! Completely changes the look of your already sweet ride!
 
Is that a sneak peak at some proprietary A pillar mounts???
 
Testing to see if this is brighter than the Ford LED high beams!



Thanks @legmar - I have a couple questions...

1) On-topic: Could this be partially due to aiming and are the high beams just illuminating over the area that the light bar hits? I'm curious how the low beams would look in this scenario.

2) Off-topic: What's with the closed captioning everyone is adding to their videos these days? YT already has this feature that can be turned on if desired. I find it a bit distracting...
 
Thanks @legmar - I have a couple questions...

1) On-topic: Could this be partially due to aiming and are the high beams just illuminating over the area that the light bar hits? I'm curious how the low beams would look in this scenario.

2) Off-topic: What's with the closed captioning everyone is adding to their videos these days? YT already has this feature that can be turned on if desired. I find it a bit distracting...
1) good question. I have video of the low beams as well that I’ll post. I also have some drone shots that are pretty intriguing to see.

2) the captions are popular to add for instagram, and I post my same shorts to both instagram and YouTube.
 
I need some help! On my brand new F350 I ordered and the build sheet says I have it but can’t find my block heater cord. Can anyone tell me where they found theirs tied up on delivery?
 
I need some help! On my brand new F350 I ordered and the build sheet says I have it but can’t find my block heater cord. Can anyone tell me where they found theirs tied up on delivery?
It is tucked into the front of the bumper... Reach into the front of the bumper towards the middle of the bumper near the passenger side tow hook. It will be just above that point.
 
It is tucked into the front of the bumper... Reach into the front of the bumper towards the middle of the bumper near the passenger side tow hook. It will be just above that point.
Our Trail Captain knows best! @DTX2023Tremor we appreciate you!
 
Thanks for posting, been wanting to add a front license plate but didn't realize there was a part for if you had the winch...i mean, obviously they'd have to for some states...but in the Great State of Florida, we don't need it, but been wanting to rock a Florida flag vanity plate. #flogrown
 
Agreed. I was shocked when they told me the price. I asked about the platinum and decided against it due to cost. Sadly, they are the only suppliers anywhere close. Same bedliner was $500 3 years ago. Appreciate the contact info.
I have a good line x dealer in Phoenix if you come down here. 3 hours start to finish. Premium is 650 out the door
 
Thanks for posting, been wanting to add a front license plate but didn't realize there was a part for if you had the winch...i mean, obviously they'd have to for some states...but in the Great State of Florida, we don't need it, but been wanting to rock a Florida flag vanity plate. #flogrown
The front license plate mount for a hidden winch is LC3Z-17A385-BA for the Ford part. It will mount the license plate below the winch.

I ordered this mount for my truck which is a flip-up style and can accommodate a few different setups. https://amzn.to/3QCcvC6
 
I know I’m going to look for this later, so linking to my RV Ford camera install project from my build thread.

Post in thread 'Furrion Pre-wire, to Ford Rear Trailer Camera??'
https://www.fordtremor.com/threads/furrion-pre-wire-to-ford-rear-trailer-camera.18331/post-384348

IMG_4681.webp
IMG_4679.webp
 
Today I finally used some Permatex RTV to repair my floppy cab trim. I cut off the little plastic bit that was originally around the rivet before I glued it all down. Hoping it holds!!

IMG_1666.webp
IMG_1665.webp
IMG_1664.webp
IMG_1668.webp
 
Got me curious, think we pull that moulding to install the roof rack in the group buy. Hard to tell from the instructions if the trim piece is slotted or we break the trim piece to get it off the rivet.
 
Last edited:
Got me curious, think we pull that moulding to install the roof rack in the group buy. Hard to tell from the instructions if the trim piece is slotted or we break the trim piece to get it off the rivet.
I’m pretty sure you have to break it. Otherwise, Ford wouldn’t be pulling the rear glass to install new ones. But this is just a guess.
 
Got me curious, think we pull that moulding to install the roof rack in the group buy. Hard to tell from the instructions if the trim piece is slotted or we break the trim piece to get it off the rivet.
Ill be making a video on this process.

You will need to pull the molding and use a box cutter to add space for the mounting feet to get through the moulding.

Yes, when the back piece is pulled through the rivet/screw (hard to tell) behind the rear glass panel, you'll just need to get some RTV silicone or Sika 221. Ours has held true for 6 or so months.

G
 
Back
Top Bottom