🛠️ What did you do to your Tremor today? [2026 edition]

Finally broke down and got a Borla S type for the truck. Had one on a prior 5.0 F150 and loved it. The 7.3 doesn't disappoint with a high quality exhaust.


IMG_6400.webp


IMG_6417.webp
 
Made a bracket and added a Blue Sea ground bus bar to make thing’s easier to wire.
IMG_1435.webp
IMG_1441.webp
 

Attachments

  • IMG_1435.webp
    IMG_1435.webp
    603.3 KB · Views: 8
Had some noise that I troubleshooted for almost a year and finally figured it out. It was the Fox ATS steering stabilizer. The Rod end was hitting my sway bar when making a turn at the bottom of a steep hill. I got the relocation setup that Fox released to change the way it mounts and works. Got it on today and seems to make a lot more sense. Was not a tough install. I was a little confused on “making the shock parallel” with the tie Rod but I believe I have it installed correctly. I think this is something that should be done to any Superduty using this stabilizer. The old mounting was at an odd angle, pushing on a cast iron stock mount that can crack and the possibility of interference with the sway bar.
Glad Fox addressed this situation.
 

Attachments

  • IMG_9021.webp
    IMG_9021.webp
    168.8 KB · Views: 42
  • IMG_9024.webp
    IMG_9024.webp
    137.6 KB · Views: 44
  • IMG_9023.webp
    IMG_9023.webp
    180.1 KB · Views: 41
  • IMG_9022.webp
    IMG_9022.webp
    110.1 KB · Views: 47
Well the coating started flaking on the tailpipe(I know polished/chrome is hard to prep so my buddy will redo it), so I decided to try making my Banks exhaust tip work. It sticks out a littler farther than I prefer but right near the factory measurements and where it was with the Banks Exhaust.
IMG_4395.webp

IMG_4397.webp
IMG_4401.webp
IMG_4400.webp
 
Last edited:
Bought the red tiger front and rear dash cams for my three trucks and my wife's car. Parked mine looking directly at the sun to check on it's heat resistance seems good so far. Wifes car doesn't have a cigarette lighter so I had to buy the hardwire kit for her just got finished hard wiring hers and ordered one for my truck 😉
Got it on a deal about $135 altogether with the hardwire kit.
REDTIGER 4K Dash Cam Front Rear,... https://www.amazon.com/dp/B098WVKF19?ref=ppx_pop_mob_ap_share
 
Well the coating started flaking on the tailpipe(I know polished/chrome is hard to prep so my buddy will redo it), so I decided to try making my Banks exhaust tip work. It sticks out a littler farther than I prefect but right near the factory measurements and where it was with the Banks Exhaust.
View attachment 254983
View attachment 254984View attachment 254986View attachment 255000
Did you cut the stock pipe where it goes 4”- 5” ? Then just clamp on the Banks tip?
 
Basically finalized my wheel+tire setup, and my Diamondback cover + yakima rack for my RTT/Thule box.

Trying to wait until I get a production date to start ordering parts.
 
Did you cut the stock pipe where it goes 4”- 5” ? Then just clamp on the Banks tip?
I cut it at the transition from the 3.5 to 4(where the dual tip got welded on). I added(welded) the 4 to 5” adapter to clamp the Banks tip onto the exhaust.
 
View attachment 255009
Got the new Badlands Pro jack from the sale at Harbor Frieght.
I was wondering about these. Looks like an awesome jack that can actually get the right height without using blocks - question though - does everyone feel comfortable using a 3 ton jack on a ~8k lb truck? Obviously one end (front/back) at a time is probably not going to be over 3/4 the weight of the truck but i was just curious if this is normal. Its next to impossible to find a jack that can do 4 or 5 tons but also get to the height these trucks need to get off the ground
 
Yes. I have had the Harbor Freight aluminum 1.5 and 2 ton jacks since they came out. Probably over 20 years for the smaller one and around 18or 19 on the bigger one. They will easily handle nameplate loads. The 2 ton was my primary jack on my 2nd Gen Ram on 42"s, and I did the entire suspension swap on my Power Wagon with them. I regularly use the 2 ton to jack up my trailer axles (~3klb each tire static.) I expect this just to benefit from the additional features (bigger tires, skid plate, grab handles, etc.) Consider Ford specs a 4 ton jack for a dually and a six ton for a F600 (GVWR 22klb) I am not worried.
 
I was wondering about these. Looks like an awesome jack that can actually get the right height without using blocks - question though - does everyone feel comfortable using a 3 ton jack on a ~8k lb truck? Obviously one end (front/back) at a time is probably not going to be over 3/4 the weight of the truck but i was just curious if this is normal. Its next to impossible to find a jack that can do 4 or 5 tons but also get to the height these trucks need to get off the ground
If you are lifting the entire axle off the ground, it’s best to do one side and secure it with a jack stand. Then lift the other side (and secure). Each corner will be under 2 tons.
 
radio2.webp
Installed two unrelated things behind back seat:
  1. ARB compressor
  2. ICOM ham radio

radio.webp

mic.webp
antenna.webp
airhose.webp
speaker.webp


Air compressor:
  • Protected from elements compared with exterior mounting
  • Large diameter, metal-reinforced air hose essentially acts like a small air reservoir
  • Probably overdid the power wires (4awg through passenger floor grommet)
  • Gets hot, so have to drop seat back for heavy use :(
  • Made a DIY 4-tire inflation with flexzilla hose
  • On upfitter switch 5 to run with battery (although should run truck for any serious use)
Radio:
  • Faceplate looks factory up by the upfitters
  • Radio box hidden away behind back seat
  • Antenna bracket screws in behind reverse light (no holes in truck)
  • Home-ran and isolated the power wires to secondary battery (trying to avoid interference)
  • Speaker is under back seat with holes drilled to let sound through, then covered with standard speaker cover.
  • Radio can do 2m and 70cm, plus marine, GMRS, and MURS (although not legal in these bands)
  • No more sunglasses holder :(
  • Not sure 2-way radio is worth it anymore with cell phone reception getting so much better (radio is for hunting, not SHTF)
 
Last edited:
paid it off today!! (now just got to wait for the title to come in the mail)
also -- I've ordered a lot from PMF Suspension a few weeks back, that just shipped and should be here soon.
Finally decided and ordered my wheels and tires today too:
KMC Impact FFT - Gloss Back - 18x9 0 mm offset
38x11.5x18 Nitto Ridge Grapplers
 
Back
Top Bottom