🛠️ What did you do to your Tremor today? [2026 edition]

The range on these things are impressive, going from boulevard cruiser to stiff is just a few clicks and some air pressure.

I've been dialing mine in too:
Front — LSC: 5 / HSC: 7
Rear — LSC: 6 / HSC: 9

Thinking I need to bump the front to LSC 6 / HSC 8. Highway plushness will suffer a little, but it'll help tame the springiness going over rocks. Without a bed full of gear I'm sitting pretty close to a 50/50 weight split, so the damping should be roughly symmetrical too.

Interesting that you're running LSC fully open across the board.
I’m not really off-road much and when I am it’s low speed- crawling so I figured I’d try all the way open for softest ride when I jump a curb or hit speed bumps etc 😂😂
 
Added a few parts so far. All ideas I get from the forum.

Warn Super Duty Winch. Wired with the interrupter to an uplifter. Factor 55 Ulta hook. Looks great and perfect fit.

Warn manual hubs with Method open center caps. Also Method valve stem covers. I really like the way the hubs and open center caps look. The hubs are very well built compared to OEM.

M&R light bar The LED white light wired to uplifter. Amber back light also to uplifter for now. I’m going to put the amber back light with the running light circuit when I install the raptor grill lights.

Center console vault from Apollo Off-Road.

Next on list is Baja fog lights, Baja Ditch lights, raptor grill lights, under hood LED light, horn blaster train horn, continue reading the forum for more ideas.
 

Attachments

  • IMG_0041.webp
    IMG_0041.webp
    338.4 KB · Views: 50
  • IMG_0039.webp
    IMG_0039.webp
    274.6 KB · Views: 51
  • IMG_0042.webp
    IMG_0042.webp
    255.9 KB · Views: 53
Ok I'm starting a project that I thought was going to be easy, but here I am. I am trying to run a fulltime hot wire to the front console area, just opposite of the factory USB-C/USB-A plugs. I thought I would be able to access the area with my hand when I removed the glovebox. Not the case. For those that have dug more into the dash, how does one access this area?
 

Attachments

  • IMG_9492.webp
    IMG_9492.webp
    246.2 KB · Views: 51
  • IMG_9493.webp
    IMG_9493.webp
    242.6 KB · Views: 52
  • IMG_9494.webp
    IMG_9494.webp
    688 KB · Views: 48
Not a very impressive mod. I finally had the Truck Detailed an added some Tuff skin sill protectors.

What I learned in the Process is I don't like putting stickers on. Looked easy, but in the end they are not 100% perfect. But then again, as my Primary Hunting Truck, it's good enough.

1772312133857.webp
1772312183413.webp


1772312091495.webp
 
  • Like
Reactions: MVI
I thought at first it was just a funny comment. But, that last pic ...

It looks great and will look great going down the road.
 
It was another 70 degree day in Denver so I washed the truck. Does that count?

My water sucks so I got a portable deionizer to try and avoid spots. Getting dark now so I’ll see how well it did tomorrow morning.

I’m trying to not use a chamois on this big of a truck.
 
It was another 70 degree day in Denver so I washed the truck. Does that count?

My water sucks so I got a portable deionizer to try and avoid spots. Getting dark now so I’ll see how well it did tomorrow morning.

I’m trying to not use a chamois on this big of a truck.
I use an electric leaf blower. That gets 90% or the water off. Then I follow it up with a towel from The Rag Company. It also helps that I piped in water from the softener to the outdoor hose bibs for car washing.
 
I use an electric leaf blower. That gets 90% or the water off. Then I follow it up with a towel from The Rag Company. It also helps that I piped in water from the softener to the outdoor hose bibs for car washing.
I tried using a small Ryobi bench blower and it was useless. Next time I will get the big guy out!
 
Back
Top Bottom