🛠️ What did you do to your Tremor today? [2026 edition]

Stop that or I'm taking away your Xbox.
Xbox.... Ew. 😜
1000018404.gif
 
Don’t tell me you’ve never seen Clerks.
At some point in my past...yes. I have overloaded myself with movies and shows and books. To the point I think I can finally watch/read some stuff again and not remember everything as soon as the first scene/chapter starts 🤣🤣🤣
 
Silent Bob is the best. And we used to hangout with a gal we called Sloppy Eighths for obvious reasons…
 
I stopped by to post that I finally got rid of the damned chrome lug nuts, but realized I’m stuck in this pit, working for less than slave wages. Working on my day off, the goddamn steel shutters are closed, I deal with every backward ass fuck on the planet. I smell like shoe polish. My ex-girlfriend is catatonic after fucking a dead guy. And my present girlfriend has sucked 36 dicks.
 
No.

Unlike most "nominal" 35s, especially those in flotation sizing, the Duratracs measure a true 35.1" when new.







It is the sweet spot, too, and when fitting a nominal 37" that measures 36.5. It's right on the money, in fact.

One thing folks seem to be overlooking is the "loaded radius"/dynamic circumference being physically smaller than the tire's actual inflated but unloaded diameter/circumference.

2799 works.
Something weird happened. I changed mine to 2799 and now I’ve got service and engine light on. The code is p0610 control module vehicle options error.

I’ve done plenty of things in forscan and never gotten errors like this
 
Something weird happened. I changed mine to 2799 and now I’ve got service and engine light on. The code is p0610 control module vehicle options error.

I’ve done plenty of things in forscan and never gotten errors like this
 

Attachments

  • IMG_2235.webp
    IMG_2235.webp
    256.6 KB · Views: 17
Something weird happened. I changed mine to 2799 and now I’ve got service and engine light on. The code is p0610 control module vehicle options error.

I’ve done plenty of things in forscan and never gotten errors like this
Hey my friend, looking at the screenshot you sent, the problem is your OBD2 adapter.

Notice the yellow warning near the top: "Adapter: ELM327 v1.5" followed by "The adapter is NOT recommended for this car." Newer Super Duties (especially 2020+) have complex CAN bus networks that older or cheap ELM327 clones simply cannot handle. That's why your log is full of "Unable to read DTC" errors for almost every major module (PCM, TCM, ABS, etc.). The adapter is dropping communication.

When you changed the tire size to 2799mm, the adapter likely failed to complete the write process properly, or it couldn't perform the required module relearns that have to happen after a tire size change. This mismatched data is what triggers the P0610 (Vehicle Options Error) and the engine light.

Here is how to get it fixed:

Stop using that adapter: Don't try to write any more changes with the ELM327, as incomplete writes can permanently corrupt a module.

Get a recommended adapter: Grab an OBDLink EX (wired) or vLinker FS (wired). These are the gold standards for modern Fords and will read all those modules perfectly without dropping the connection.

Restore from backup: Once you have the new adapter, load your original As-Built backup for the module you changed (likely the BdyCM) to revert the tire size back to stock.

Clear DTCs: Clear all the error codes. The wrench and engine lights should turn off. To verify this worked, cycle the ignition and rescan to ensure the P0610 code is gone.

Re-apply the change properly: If you still want to change to 2799, make the change with the new adapter. Immediately after writing the new size, go to the Service icon (wrench) in FORScan and run the "PCM Relearn" and "AWD/TCM Relearn" procedures. Newer trucks strictly require these relearns when tire sizes change to prevent that exact P0610 code.
 
Back
Top Bottom