🛠️ What did you do to your Tremor today? [2026 edition]

Confirmed that a 37x12.5R18 T/A KO3 will fit in stock spare location when aired down to 15 psi and forscanned the truck to let it know that it has larger tires.

The tire fit is TIGHT, but it is resting on all four of the plastic pucks underneath the bed. The factory tailpipe just kisses it, so it will get wrapped with exhaust wrap today and I’ll swing by my muffler shop next week. I believe a tweak to the rear-most exhaust hanger will give it a 1/4 inch of clearance or so. Not very worried about it as truck is a vegan and after running down Highway at 90mph I could put my hand on that section and leave it without burning myself.

I can recommend the procedure at the link posted below for the Forscan mods. No issues after following his guidance and speedometer tracks gps perfectly up to 90mph.

So, need to chalk test it, tweak exhaust hanger, and wrap exhaust pipe to be done, but we are getting there. Pretty happy with it now that Speedo matches and tire fits under the bed. Truck rides better, definitely looks better and hey, I have always loved me some All Terrain T/A’s.

View attachment 268614

https://www.thebakeradventures.com/post/forscan-speedometer-recalibration-37-inch-tires-ford
Impressive. I tried to put my last trucks 38” spare nitro grappler, worn to probably 50% tread and NOT a chance of getting it in there. Yes, have banks exhaust, but it’s hitting my rear diff cover too. 😂 looks like spare in the bed is the game plan again or on roof of canopy like last truck.
 
I opened up my hood to put in windshield wiper fluid and found the “mild” corrosion ford told me about was just a tad out of control.
IMG_3310.webp
IMG_3311.webp
IMG_3312.webp
IMG_3313.webp


So I got some cleaner and went to town on the battery after I got it out. Then I had to get the paint off. I used a power drill wire brush, cleared off everything it could reach and applied rubberized paint. While that was drying on one side, I put the battery back in. Then flipped the battery holder, applied paint and connected the battery terminals. Finally, installed the battery holder and applied the protectant.

Looks much better I think.
 
Made a new Pintle Mount and Rear Hitch Slider - to be tested out in Moab

Details at MVI's F350 Build

1788892499585.webp
 
I opened up my hood to put in windshield wiper fluid and found the “mild” corrosion ford told me about was just a tad out of control. View attachment 269073View attachment 269074View attachment 269075View attachment 269076

So I got some cleaner and went to town on the battery after I got it out. Then I had to get the paint off. I used a power drill wire brush, cleared off everything it could reach and applied rubberized paint. While that was drying on one side, I put the battery back in. Then flipped the battery holder, applied paint and connected the battery terminals. Finally, installed the battery holder and applied the protectant.

Looks much better I think.
Looks like you needed to jump on the group buy for the billet hold downs a few months ago.
 
I followed there installation instructions and it still broke.
i have broken fox uppers and a couple carli lowers do to improper installation. i now let some nitrogen out of carli lower ,install correctly , then have refilled to correct amount
 
Looks like you needed to jump on the group buy for the billet hold downs a few months ago.
I was thinking about that while working today.
 
I opened up my hood to put in windshield wiper fluid and found the “mild” corrosion ford told me about was just a tad out of control. View attachment 269073View attachment 269074View attachment 269075View attachment 269076

So I got some cleaner and went to town on the battery after I got it out. Then I had to get the paint off. I used a power drill wire brush, cleared off everything it could reach and applied rubberized paint. While that was drying on one side, I put the battery back in. Then flipped the battery holder, applied paint and connected the battery terminals. Finally, installed the battery holder and applied the protectant.

Looks much better I think.
Holy shit man.... Pretty sure you're just taking pictures of a truck sitting in a field with grass growing all around it.... 🤣🤣🤣
 
Holy shit man.... Pretty sure you're just taking pictures of a truck sitting in a field with grass growing all around it.... 🤣🤣🤣
Stopped myself but was about to say "excuse me...sir...have you tried not parking in the ocean?" 😂
 
Stopped myself but was about to say "excuse me...sir...have you tried not parking in the ocean?" 😂
I bought beat up old used ass vehicles that had nicer looking batteries/hold Downs than that shit
 
I finished Welding up the Rear Hitch Slider that attaches via a Modified Pintle Mount


more photos at MVI's F350 Build

1788991626923.webp
 
That's some pro-level looking work. Your fabricator must be really good at what they do.

Thanks,

The differential sight glass is still my favorite mod though.
 
Last edited:
Back
Top Bottom