SUCCESS!!!! 37’s on factory rims, no lift, no rub….

Yeah, pulled a tendon trying to yank the 37x12.5R18 spare out from under the truck awhile back; better after 6 months. Now I'm more careful and use the jack below to adjust the axle height to where I can lay the top wheel bolt hole onto the lug and then use the jack to lift enough for the rest to slide into place.

https://a.co/d/eap1pG2
Pricey, but this along with a 12x12x3 plywood block have gotten me out of trouble offroad more than I'd like to admit. I have a 6ton manual hydraulic as backup, but have never used it other than in jack stand mode.
 
I don’t have a 22 to compare against but I’ve read a few articles that have mentioned changes to the 23’s to allow fitment of 37’s. So far I’d have to agree!
You're convincing me I need fender flares now LOL. Looks great mate!
 
I guess a more appropriate question for the group - who is running a full-sized spare and how often have you needed to use it?

I've always bought 5 wheels and 5 tires. Yes, more cost up front, but 5-way rotation buys me more life out of my set, and if I ever need a spare I know it'll be the same as the rest (though, I have never had a flat on E-rated true 3-ply sidewall tires)

Everyone has their own reasons.
My spare is a dedicated spare i don’t put it into rotation just yet, but i do have the 5th wheel and tire that does go into my 5 wheel rotation. Once the other 5 reach the tread of the 6th spare, it too will go into rotation. I’m dedicated to AT3s, so having 6 wheels is good for longevity. Plus, during winters i throw the 6th into the bed for added weight.


Dudes! I'm tellin' ya! Thank you! for corroborating what I've always thought was another one of my extravagant ways of enhancing my truck's utility and reliability especially when deep into off highway travel.

I have for the last 7 years purchased (two different sets of) 5 wheels and 5 tires for my F150 which currently sits on Method 705 Beadgrips 17 X 8.5 25mm et wearing 34 X 10.50 X R17LT D Load Range Toyo A/TIII.

I do a five-tire rotation for two reasons: ABS/all-the-other-electronic-nanny-software like RSC, etc... and because I had installed an Eaton Truetrac all-steel helical gear-type limited slip in that truck.

Too, a five-tire tire rotation is easier because we only have to lift one corner of the truck at a time. No more jacking entire axles off the ground one after the other, the four jack stands, etc... (okay, I will use ONE jack stand in this case). I start by dropping the spare which goes onto the right rear then continue with a Rearward Cross rotation ending with the left front moving into the spare's location.

Since folks are getting +/- 50,000 miles from the Goodyear Duratrac tires, it's gonna be awhile (I'll go 25,000 then sell the Duratracs takeoffs) before I invest in a new set of five A/TIIIs in 37 X 12.50 X 18 but unless a better tire for this application appears, this will be what I'll do.

Posting all of this to say that I have recently purchased from Ford Parts a fifth 2025 Ebony Black Gloss/Machined TREMOR 18 X 8 wheel. The wheels on my '25 Tremor are the first factory wheel I have not! wanted to swap out for something different. I do like these wheels. Sure, there may be a lighter wheel in the same size that is just as strong (METHOD) but I like my Tremor wheels.

Now I just have to get over to a competent shop that won't damage this brand new fifth Tremor wheel and get my fifth Duratrac mounted on it. 5000 miles (first tire rotation) will be here soon enough!
 
Dudes! I'm tellin' ya! Thank you! for corroborating what I've always thought was another one of my extravagant ways of enhancing my truck's utility and reliability especially when deep into off highway travel.

I have for the last 7 years purchased (two different sets of) 5 wheels and 5 tires for my F150 which currently sits on Method 705 Beadgrips 17 X 8.5 25mm et wearing 34 X 10.50 X R17LT D Load Range Toyo A/TIII.

I do a five-tire rotation for two reasons: ABS/all-the-other-electronic-nanny-software like RSC, etc... and because I had installed an Eaton Truetrac all-steel helical gear-type limited slip in that truck.

Too, a five-tire tire rotation is easier because we only have to lift one corner of the truck at a time. No more jacking entire axles off the ground one after the other, the four jack stands, etc... (okay, I will use ONE jack stand in this case). I start by dropping the spare which goes onto the right rear then continue with a Rearward Cross rotation ending with the left front moving into the spare's location.

Since folks are getting +/- 50,000 miles from the Goodyear Duratrac tires, it's gonna be awhile (I'll go 25,000 then sell the Duratracs takeoffs) before I invest in a new set of five A/TIIIs in 37 X 12.50 X 18 but unless a better tire for this application appears, this will be what I'll do.

Posting all of this to say that I have recently purchased from Ford Parts a fifth 2025 Ebony Black Gloss/Machined TREMOR 18 X 8 wheel. The wheels on my '25 Tremor are the first factory wheel I have not! wanted to swap out for something different. I do like these wheels. Sure, there may be a lighter wheel in the same size that is just as strong (METHOD) but I like my Tremor wheels.

Now I just have to get over to a competent shop that won't damage this brand new fifth Tremor wheel and get my fifth Duratrac mounted on it. 5000 miles (first tire rotation) will be here soon enough!
Though I do favor a 5-tire rearward cross rotation myself, I think I'm going to just stick with the tremor wheels and tires with a 4-pattern rotation until I have the cash to swap out for a Method and either Falken AT4W or Toyo AT3.
On monday, I'm taking my wife's Rav4 to get the Falken AT4W (overkill I know haha) installed. It'll be a nice test run to see how I like the tires on the smaller SUV and make a subjective decision on how that may translate to my truck...
It's also less than half the price to put these on the Rav4, and it's due for tires anyway so why not?!

I'm just trying to find the right wheel now for my truck. I do really like the stock setup, but eventually would like something like a Method 703 clear coat (no sure that wheel is compatible with our lug pattern, but that's the wheel I like the look of most right now)
 
I agree!

If I went with a new Method wheel for my SuperDuty, it'd more than likely be a machined finish. My XLT has that snazzy plastic vacuum metalized chrome face and "chrome" bumpers (chrome/not chrome/don'tknowwhatitis).

Speaking of, it's time to go clean it's windows! for my Friday late breakfast getogether w/ the boys.

Cheers!
 
Hey all. Understand we are talking AT3s here, but I am a diehard BFG fanboy, and am looking at 37x12.5x18 KO3s. BFG website lists them as the same size as the Toyos (36.5 and 12.5 on 10" wheel).


Anyone have any leads on guys running these on a stock setup?
 
Hey all. Understand we are talking AT3s here, but I am a diehard BFG fanboy, and am looking at 37x12.5x18 KO3s. BFG website lists them as the same size as the Toyos (36.5 and 12.5 on 10" wheel).


Anyone have any leads on guys running these on a stock setup?

Are you intending to run the stock Tremor wheels or aftermarket ones? The stock wheels are 8" wide and I'm not sure if/how that might affect tread width and/or diameter. I could guess that they would work with little or no rubbing on stock suspension but whether it will fit in the spare tire well, I have no idea. Maybe.

Hopefully someone running those tires sees this and can report results, and what wheels and offset they are running.
 
Yep, was thinking of doing exactly what Tramper did, but subbing the AT3s for KO3s.
Load range F. I thought about the same thing but didnt want the ride of a load range f tire on washboard roads
 
Last edited:
That's a bit deceiving actually. Some manufactures use E and F on different specs. I always look at the actual load rating. Both tires are rated at 128 load rating (3970lb), Toyo just happened to call that E, and BFG calls it a F.. But actual specs are identical.
 
Haven’t seen much talk (that I can remember) about BFG HD terrains. Rim spec is 128 load, with 7.5-11.5 rim width. Anyone run them on stock wheels?

Seems like it’s perfect.
 
I’m not sure if this has been addressed yet or not. I couldn’t find any information on the forum when I searched.

I have a ‘24 F350 SCSB 4x4 with the 7.3 gas. I’m somewhat certain that this truck has the same rear suspension as the Tremor does (leaf pack) so probably similar ride height. Does the F350 with standard front spring package sit at the same ride height as the Tremor spring package?
I’m trying to compare the two truck models with ride height/ clearance to possibly fit the Toyo AT3 37/12.50/18 on a set of Tremor take offs, once I find a pristine set, like @TRAMPER has done with his authentic Tremor.
 
Haven’t seen much talk (that I can remember) about BFG HD terrains. Rim spec is 128 load, with 7.5-11.5 rim width. Anyone run them on stock wheels?

Seems like it’s perfect.
The guy on social media who runs/works/owns Whiteface Ford - not quite sure which- runs them on his rigs. He seems to like them. his set ups are more service body /work trucks so not sure if they would translate to a tremor type experience.
I’m not sure if this has been addressed yet or not. I couldn’t find any information on the forum when I searched.

I have a ‘24 F350 SCSB 4x4 with the 7.3 gas. I’m somewhat certain that this truck has the same rear suspension as the Tremor does (leaf pack) so probably similar ride height. Does the F350 with standard front spring package sit at the same ride height as the Tremor spring package?
I’m trying to compare the two truck models with ride height/ clearance to possibly fit the Toyo AT3 37/12.50/18 on a set of Tremor take offs, once I find a pristine set, like @TRAMPER has done with his authentic Tremor.
the rear leaf springs could/would be the same but the front will sit 1.5” lower then a tremors- conversely - the rear “block” for a tremor is 1” taller then a standard rear super duty block.

So a stock super duty will sit 1.5” lower in front - 1” lower in back - but the leaf springs could be the same .

Correct me if I’m wrong but I think your reasoning is since you have the same “leaf springs “ then the truck should sit the same height and that’s not correct. The tremor sits 1.5” taller in front because it has taller coil springs and the rear sits higher because of the rear block.

those items are pretty easy to change out honestly - there are people selling fairly new tremor coils and shocks / blocks either on FB marketplace or eBay and would get you the look your going for.

Back in 22- I bought a f250 fx4 and bought a tremor suspension for $400- the tremor rims for $1k and no one knew the difference. Attached is the pic of my 250 fx4 I turned into a Fremor (fake tremor )

IMO the 17-22’s look perfect with the 1.5” and 35’s

However the 23+ look best with 2.5+ suspension upgrade and 37’s iMHO.
 

Attachments

  • IMG_2237.webp
    IMG_2237.webp
    310.5 KB · Views: 63
  • IMG_2227.webp
    IMG_2227.webp
    573 KB · Views: 64
  • IMG_2235.webp
    IMG_2235.webp
    263.4 KB · Views: 63
I’m not sure if this has been addressed yet or not. I couldn’t find any information on the forum when I searched.

I have a ‘24 F350 SCSB 4x4 with the 7.3 gas. I’m somewhat certain that this truck has the same rear suspension as the Tremor does (leaf pack) so probably similar ride height. Does the F350 with standard front spring package sit at the same ride height as the Tremor spring package?
I’m trying to compare the two truck models with ride height/ clearance to possibly fit the Toyo AT3 37/12.50/18 on a set of Tremor take offs, once I find a pristine set, like @TRAMPER has done with his authentic Tremor.

Like others have said, rear springs are the same but blocks are taller on tremor. If you put tremor springs on the front, you will want to raise the rear to tremor height by using the tremor blocks or with a full progressive leaf pack, etc. Putting Tremor springs on the front of a non-tremor truck but nothing to the rear would probably level you when empty, but you'd be squatted with any type of load. Since you are using a slide in camper, you do not want a "leveled" truck. You need the rake so the rear settles level with a load. Whatever height you raise the front, you'll want to raise the rear an equal amount.

Front tremor springs are only about 1" taller than non-tremor springs. Ford advertised tremor as 1.5" taller but around .5" that is from the taller tires equipped on a Tremor vs a non-tremor. The front springs are only 1" taller unless you go with a stiffer springs rate than your non-tremor. I'm going up to a Tremor spring that is one spring rate heavier than my non-tremor front springs. My f250 non-tremor 7.3 has 4,800lb springs. I have a set of 5,200lb tremor springs laying here that I'll install in the spring. My STC slide-in pickup camper will be on fulltime, so the extra spring rate makes sense. I'll also do a full progressive rear leaf pack.

I have two friends that did this exact same thing and front lift was nearly 1.5" due to the combination of both the taller spring height and heavier spring rate. Using the same spring-rate tremor spring will net 1" lift.
 
Last edited:

They’re made by bushwhacker but have a Ford part number.


Also see this thread started by @modified for more details and some before and after and installation pics and commentary.
I like the look of the fender flares you installed, so I ordered a set for myself. Funny thing is, here in Canada, they come from Ford made by Husky liners, same part number VPC3Z16268D. I was genuinely shocked that the dealership had aftermarket products, cheaper than the aftermarket??
 
Sorry about the dumb question….
Does anyone with a 2023 6.7 diesel f350 Tremor have these tires on stock rims?
If so do you have any issues with any rubbing?
 
Just had them put on! Love the look.
Tire pressure(cold 63° F):
Front 60 psi
Rear 50 psi
Adjusted FORSCAN TPM to 50 psi.
Super smooth and quiet love the new shoes!


Couple months gone by, do you still love them?
 
Those falkens are fat boys at being 12.9 wide, and slightly taller than toyo at3s, so they rub more on the sway bar. You could try to shift your oem sway bar 1/8 of an inch and see if that helps. In my case it eliminated the rub completely, but it might not work with falkens. Shifting might start to rub the other side, it’s trial and error. 2nd option is to get a carli sway bar, expensive but it will solve your issue. Third option might be to try a hellwig bar, $400 roughly, it should be a little narrower than oem one, while being much stronger. Fourth option is 3/8 inch bora spacers, that might move the wheels out just enough to clear. Fifth option, get +18 offset rims, that will win you 3/4-1 inch of real estate and will most certainly clear the sway bar. 6th option is to get rod of the sway bar and ride without one. A few on the forum when that far:-)
Did you ever post details on moving the sway bar? I just installed my AT III and am getting a little rub at full left lock. Any help would be greatly appreciated. Thanks.
 
Back
Top Bottom