📍 Meet-Up Dayton, OH - Jan. 12th at 1 PM - Wandering Griffin Brewery

[Trilifter7]

Got the authorization already taken care of. Probably wasn't needed, but rather play it safe and have enough margin.

Perfect! Now lets just hope the weather holds out to actually get it in the air

 

[BroncOh]

Looking forward to meeting everyone at this meetup!

 

[Trilifter7]

Looking forward to meeting everyone at this meetup!

Likewise! Hopefully the location is not a bust since it was my recommendation

 

[BroncOh]

I'll be calling Wandering Griffin on Thursday to see about a reservation at 1pm on the 12th for, let's say, approximately 12 trucks. If we get there at noon, that would give us an hour or so of time to chat. I'll have about a 3-1/2 hour drive, so hopefully the weather will be good.
Might have to rig up the flame thrower on the front of truck to melt any snow/ice if not. 60 gallon tank should be beneficial for this.

 

[quad racer]

Yeah I’m looking forward as well. Met up about 10-12 years ago with some guys from the other site. I had my 08 with the V10 back then. We took turns pulling a weighted trailer up a hill to document how setups performed. Can’t wait to see all these beauties in the parking lot. No one will be held responsible if the place is a dud im sure it’ll still be fun

 

[Trilifter7]

Yeah I’m looking forward as well. Met up about 10-12 years ago with some guys from the other site. I had my 08 with the V10 back then. We took turns pulling a weighted trailer up a hill to document how setups performed. Can’t wait to see all these beauties in the parking lot. No one will be held responsible if the place is a dud im sure it’ll still be fun

If it sucks Twin Peaks is always right around the block

Also, I was on the other site then as well and remember watching the videos of you guys versus the new 6.2 pulling the trailer! That was the first real testing I’d seen on the new engine and so cool you guys were able to organize it!

 

[BroncOh]

If it sucks Twin Peaks is always right around the block

Haha, I wasn't going to mention it, because now you did! Unfortunately the current, approved, drone authorization zone would barely cover Twin Peaks

 

[Trilifter7]

Haha, I wasn't going to mention it, because now you did! Unfortunately the current, approved, drone authorization zone would barely cover Twin Peaks

Well just have to stay on the north side if we go

 

[BroncOh]

Well just have to stay on the north side if we go

I just updated the zone and it's approved! @Optimus welcome to join the peaks.

 

[Optimus🤖]

If it sucks Twin Peaks

I'm really considering attending this meeting .

 

[Alpoba]

I'm really considering attending this meeting .

Swing by NJ afterwards while you’re out east, i’ll take you out droning.

 

[quad racer]

If it sucks Twin Peaks is always right around the block

Also, I was on the other site then as well and remember watching the videos of you guys versus the new 6.2 pulling the trailer! That was the first real testing I’d seen on the new engine and so cool you guys were able to organize it!

I was super impressed with that truck. Held very close numbers to the 6.4 diesel.

 

[Trilifter7]

I was super impressed with that truck. Held very close numbers to the 6.4 diesel.

Yea I remember it was very surprising how well it did! That was pre TFL type testing at its finest

 

[WakeZilla]

Here's the official Tremor .svg if you want to use it for that. (remove .txt from the end of file)

Here's the official Tremor .svg if you want to use it for that. (remove .txt from the end of file)

So, I am not a graphics guy and playing with all of this in AutoCAD. I saved the SVG file to my Windows Fonts directory but it did not pull it in. I tweaked the "Tremor" layout but still not quite there. Do you know if there is a Ford Tremor Font? It would be cool if I could use the font for all of the text. Right now the Tremor text is all linework I drew and hatched solid.

 

[BroncOh]

She called me back from Wandering Griffin and got the date of the staff party wrong lol. (deleted last post to avoid confusion)

We're good still!

I just made the reservation for "Tremor off-road community"

Jan. 12th at 1 PM

I reserved for 15 people, so we have a good margin for extra!

 

[BroncOh]

So, I am not a graphics guy and playing with all of this in AutoCAD. I saved the SVG file to my Windows Fonts directory but it did not pull it in. I tweaked the "Tremor" layout but still not quite there. Do you know if there is a Ford Tremor Font? It would be cool if I could use the font for all of the text. Right now the Tremor text is all linework I drew and hatched solid.

No Tremor font available, are you able to resize the imported SVG in Fusion360?

 

[WakeZilla]

I don't have Fusion 360. I'll have to see if I can print it to pdf and insert it. If nothing else I can scale and trace it. I suppose I could create any of the other alphabet letters I need.

 

[WakeZilla]

Managed to trace the SVG file and create a "Tremor" alphabet for the remainder of the text.

 

[WakeZilla]

Looks better with lettering filled.

 

[WakeZilla]

OK gang. Final edit...I think?! I'm going to stop at a tshirt shop and figure out cost to print these. I'm thinking white graphics on a black tshirt. (Sorry I'm not a graphics guy and I'm working on short notice so a little boring design). I will get an idea of cost and post it up later today. Once I get price point we can see who is interested and shirt size. I can pay to have them printed and we can square up at the meet up!