22 Black Bear 🐻 Build

I’m not sure where it was on the forum, but I recall seeing someone say it was difficult to shift into D without accidentally going too far and ending up in M. Here’s a video showing how I shift into Drive perfectly every time and never end up in Manual by mistake.

 
Last edited:
I’m not sure where it was on the forum, but I recall seeing someone say it was difficult to shift into D without accidentally going too far and ending up in M. Here’s a video showing how I shift into Drive perfectly every time and never end up in Manual by mistake.

All I heard from this is don't pull out and apply slight pressure. 😏

Jokes aside this is good advice that I wasn't aware of.
 
Summer days are for tinkering with the truck! I got the Wicked Warnings Mirror White Spotlight Flood/Strobe speed override kit installed. It’s 100% plug n play, and it works great to keep the spotlights on in flood mode when driving the back roads out in the Texas Hill Country on the Frio River!

 
Super helpful! Now I've got a new technique to practice. I'm one of the "dang it I missed" guys.
 
Just a teaser… I’ll be putting together a video of my ARB install. But for now, here’s a couple pics of some of the most interesting parts!

E5C0797E-A213-4758-AEEF-C05C1CDBA59C.webp

73E49AAA-F63A-49DF-B21D-EC4DFFE7D012.webp
image.webp
 
Super helpful! Now I've got a new technique to practice. I'm one of the "dang it I missed" guys.
Hey! I'm curious - how's the new technique working for you?
 
Hey! I'm curious - how's the new technique working for you?
Well, I haven't got as much practice as I'd like. Truck has been in the shop for the last 6 days. I just got it back today, but I'm adapting to the new method just fine. Works like a champ.
 
Summer days are for tinkering with the truck! I got the Wicked Warnings Mirror White Spotlight Flood/Strobe speed override kit installed. It’s 100% plug n play, and it works great to keep the spotlights on in flood mode when driving the back roads out in the Texas Hill Country on the Frio River!

just put the limitless one on mine, it was pretty easy no strobes though
 
just put the limitless one on mine, it was pretty easy no strobes though
Nice! How was the install? I noticed you have to make some wire connections with the limitless version whereas the wicked version was just plug n play. Curious if you have any input to help others choose one or the other?
 
Nice! How was the install? I noticed you have to make some wire connections with the limitless version whereas the wicked version was just plug n play. Curious if you have any input to help others choose one or the other?
For the mirror spot lights its just plug n play. On limitless they have you cut the corner of the stock greeb plug where I see there's comes with the new grey one cut out. Don't know why i didn't think of that, would have rather cut the new vs the stock one but i'll probably never take it off. Took 10 minutes. I did their DRW 3 light bar, that I had to add a pin to the connector still pretty easy. Have the reverse on demand lights left.
 
For the mirror spot lights its just plug n play. On limitless they have you cut the corner of the stock greeb plug where I see there's comes with the new grey one cut out. Don't know why i didn't think of that, would have rather cut the new vs the stock one but i'll probably never take it off. Took 10 minutes. I did their DRW 3 light bar, that I had to add a pin to the connector still pretty easy. Have the reverse on demand lights left.
Ohh! I wonder if the limitless kit for spot light flood is plug n play, but perhaps their version for strobe requires some wire connections to be made.

Here’s their product page:

Here’s a photo which I think is of the flood version you used that’s plug n play.

94AF8CAD-9304-4EA6-A0CB-1DA6890B0F09.png


And here’s a photo (from the same product page) if their version that I think has the strobe function and isn’t entirely plug n play.
4151FD16-1B4C-4ACD-BB32-B6B94D52A5D0.png


So I think the wicked kit may be simpler for anyone who wants both flood and strobe options for the spotlight overrides.

Here’s a caveat… if you want to tie a bunch of limitless strobe modules to a single upfitter switch, then the limitless kit with the raw wires is probably better for that scenario.

6CE75787-171C-4ED4-9087-657A7F35AF11.jpeg
 
ARB Install

I decided to install my ARB twin CKMTA12 (https://www.apollo-optics.com/produ...rformance-12-volt-twin-air-compressor-ckmta12) compressor in the bed of my truck. I placed BuiltRight small panels (https://builtrightind.com/products/builtright-industries-bedside-rack-system-small-panel-2015-ford-f-150-raptor-2017-ford-f250 ) at the front of the bed. On the driver side panel, I installed a BlueSea SafetyHub 150 Fuse Block (https://www.westmarine.com/blue-sea-systems-safetyhub-150-fuse-block-11975794.html) that serves as a distribution point for power to anything I install on the back half of the truck.

CEB7C7D2-C7FB-47BA-B680-96F2EE39D654.jpeg


9B6A859C-E07B-4289-BA4F-6C161593AEF5.jpeg


883C1C18-2610-4505-A1BA-E526DDE8744B.jpeg


From there, I ran a 1/0 AWG power cable from the battery on the passenger side of the truck down the engine bay, across the top of the wheel well liner, against the frame, into the frame, inside the frame down the length of the truck, inside the frame through a cross member in the rear, out the frame on the driver side, up between the cab and the bed, into the bed through the oval cap on the lower front wall, and attached it to the power distribution block. I ran the ground cable to the underside of the bed and attached it to a factory ground on the driver side frame next to the spare tire. I did grind away the paint under the terminal to ensure a solid connection. I used dielectric grease on the connection and then sprayed it with a clear sealant after bolting it down to help prevent rust.

EE2CA5E7-2899-4F84-A643-D77260E37693.jpeg


Here’s the parts I used when putting together the power cables…

35 ft of Kolossus Fleks Kable 1/0 Red Power /Ground Wire
https://www.knukonceptz.com/mobile-...olossus-fleks-kable-10-red-power-ground-wire/

10 ft of Kolossus Fleks Kable 1/0 Black Power/Ground Wire
https://www.knukonceptz.com/search-results/sp/kolossus-fleks-kable-10-black-powerground-wire/

Gold Plated 1/0 Ring Terminal -Red
https://www.knukonceptz.com/sp/gold-plated-10-ring-terminal-red/

Gold Plated 1/0 Ring Terminal - Black
https://www.knukonceptz.com/sp/gold-plated-10-ring-terminal-black-/

KnuKonceptz Dual Wall 1 Inch (1/0 Gauge) Adhesive Lined 3:1 Heat Shrink Tubing - Red
https://www.knukonceptz.com/search-...-gauge-adhesive-lined-heat-shrink-tubing-red/

KnuKonceptz Dual Wall 1 Inch (1/0 Gauge) Adhesive Lined 3:1 Heat Shrink Tubing - Black
https://www.knukonceptz.com/search-...auge-adhesive-lined-heat-shrink-tubing-black/

You’ll need a strong wire cutter as well as a beefy terminal crimped. Here’s what I used:

Klein Tools J63050 Cable Cutter, Journeyman Cable Cutter Cuts Aluminum, Copper and Communications Cable with Shear-Type Jaws

(The cutter above is barely big enough, but it gets the job done if you cut/rotate a little at a time.)

AMZCNC Hand Operated Hydraulic Crimping Hydraulic Cable Lug Crimper 8 US TON 12 AWG to 00 (2/0) Electrical Terminal Cable Wire Tool Kit with 9 Die

(This crimper was awesome - it worked perfectly!!)

I wrapped the power cables in split wire loom and wrapped the ends with tape. I also wrapped a couple loops of tape every couple feet along the loom to ensure it held together well.

5 Rolls Tesa's Most Advanced High Heat Harness Tape 51036 Mercedes, BMW, Audi, VW

3M Scotch Vinyl Electrical Tape Super 88, Premium Grade All-Weather, 3/4 in x 44 ft, 8.5-mil thick, Black, 1 roll

I like to use a little red electrical tape around the end of the positive power cables just to make it clear which cable is positive when doing any maintenance in the future.

Gardner Bender GTPC-550 Electrical Tape, ½ in x 20 ft., Durable, Easy-Wrap, Flame Retardant, 5 Pk, Red, White, Blue, Green, Yellow

A tip to installing the wire into the loom is to use a tool like this…

Electriduct Wire Loom Insertion Tool Set for 3/8" to 2" Conduit Sleeving Installation

Here’s the loom I used for the 1/0 AWG power cables:

ZhiYo 20FT 5/8" Wire Loom Split Tubing Auto Wire Conduit Flexible Cover

Let’s talk fuses for a bit. You’ll need an inline fuse on the power cable as well as fuses for the BlueSea block. Originally, I was going to use a KnuKonceptz ANL fuse inline on the power cable, but I found an easier fuse options that also helped with my batter clutter.

What I found was a 3-way fused bus bar from Mouser.
https://www.mouser.com/ProductDetail/Littelfuse/0FHZ00853-BX?qs=qpJ%2B%2B%2Bdg6p1tph0MWK00pQ==

Then I got this 150A fuse from Mouser to use with the bus bar.
https://www.mouser.com/ProductDetail/Littelfuse/3298150.Z?qs=aGgfWYEhH7lN37SvSGko3g==&countrycode=US&currencycode=USD

To connect the bus bar to the battery post, I had to first add a product from Rugged Rocks to my battery’s positive post.
https://ruggedrocksoffroad.com/power-distribution-terminal-blocks-by-rugged-rocks.html?search=Battery block

Then I screwed 2 threaded, positive battery posts into the block from Rugged. The posts I used were super fancy and purchased from Walmart. :p The set comes with a positive and a negative post, so be sure to buy 2 sets if you also want 2 positive posts to use like I did. (Pos/neg posts are different sizes!)
https://www.walmart.com/ip/2-Pcs-Ba...lts-Positive-Negative-For-Car-Boats/418255379

The Mouser post requires these nuts for you to attach ring terminals to them.
Prime-Line 9094921 Flange Nuts, Class 8 Metric, M8-1.25, Zinc Plated Steel, (10-pack)

Here’s the main fuse you need to use on the BlueSea block for the 2 red power cables that attach from the ARB harness to the power block. These 40A fuses match the rating of the inline fuses that ARB uses.

Blue Sea Systems MIDI or AMI Marine Fuse, 40A, (2) 5251

You’ll also need some standard fuses for anything smaller you connect to the power block (though this ARB install does not need them).

Petutu Blade Car Fuses Assortment Kit 220Pcs –Standard & Mini (2A/3A/5A/7.5A/10A/15A/20A/25A/30A/35A),Car Boat Truck SUV Automotive Replacement Fuses


Another nifty change I made was to not use the ARB-supplied harness for the switch (I only used their power harness). For the switch, I created my own cable/plug that connects directly to the ARB plug on the compressor. One thing to note is that this “switch” wire does 2 things… 1) it signals the relay in the compressor to turn on and 2) it powers the small cooling fan inside the compressor. Since the wire is technically doing more than just signaling the relay, I decided to use a 14 AWG wire for peace of mind when I built my custom wire harness for the switch.

92A5A46A-B281-4FA5-BF56-A64ED3E2A7F0.jpeg


0E45D3A7-04E3-4C8D-9B3E-32226953FB86.jpeg


Here’s the 14 AWG wire I used for my signal wire connected to the upfitter switch:

InstallGear 14 Gauge OFC Primary Remote Wire, 100-feet - Yellow

Wire loom for the signal wire:
ZhiYo 50 FT 1/4” Wire Loom Split Tubing Auto Wire Conduit Flexible Cover | High Temperature Heat Resistant -40F to 257F | Plastic Cover for Electrical Wires & Cables

Insertion tool for the small, 1/4” loom:
Yellow Loom Tool - Cable Insertion for Small Bundles from 1/4" to 3/8"

Here are the parts you need to terminate the 14 AWG wire into a plug that is compatible with the ARB plug.

The plug is a Delphi style plug.

Crimper:
IWISS Weather Pack Crimper Tools for Delphi APTIV Packard Weather Pack Terminals Metri-Pack Connectors for Sealed Terminals

Plug: (You’ll use the male side of this plug that has the purple rubber on it.)
Delphi Metri-Pack 150 Series 3-Way Connector w/16-18 AWG Sealed Waterproof Set

The plug has space for 3 wires, but the only wire we care about is the center pin wire. This is the “signal” wire that is used by the ARB compressor. (It’s equivalent to the purple wire on the ARB switch harness). Since we will not be using the 2 outside pins, seal off your connector by getting 2 rubber plugs to insert:

https://www.customconnectorkits.com/12059168/


That’s all you need to build your own, clean switch harness that is compatible with the factory ARB plug. Then, when you run the yellow switch wire to the upfitter switch, I like to connect it using JRready DTHD connectors. These allow you to easily remove or swap accessories with each of the upfitter switches.


I used heat shrink butt connectors with solder inside them to easily connect the yellow wire to my upfitter wire.

Limited-time deal: TICONN 250 Pcs Solder Seal Wire Connectors, Heat Shrink Butt Connectors, Waterproof and Insulated Electrical Wire Terminals, Butt Splice (250PCS)

To get a good heat shrink, I used a heat gun from Harbor Freight with a metal adapter on the end to concentrate the heat around all sides of the connector.

Then I shrank heat shrink tubing on top of the connection.
Wirefy Heat Shrink Tubing Kit - 3:1 Ratio Adhesive Lined, Marine Grade Shrink Wrap - Industrial Heat-Shrink Tubing - Black 180 PCS

Then I wrapped it in tape and wire loom.

Here’s the connectors I chose to use for this purpose. I really like them!
543ADDD9-216F-4789-9D52-2A2BC3F19170.jpeg

JRready ST6286 1 Pin DTHD Connector 4 Sets,IP67 Waterproof Single Terminal Connectors for Heavy-duty Applications,Contact Size 12 Crimp Wire Gauge 12-14AWG,25A

4-way crimper for the above plugs:
IWISS Closed Barrel Crimper 4 Way Indent,8 Impression Type for Deutsch Solid Contacts gage 12 (IWD-12)

Bonus item… my favorite zip ties for automotive and outdoor projects:
TR Industrial Multi-Purpose UV Resistant Black Cable Ties, 8 inches, 100 Pack


For the airline hoses, I got a bunch from Northridge 4x4 as well as Trail Recon.

https://www.northridge4x4.com/search?q=arb+hose
https://trailrecon.com/search?query=Arb-hose


At a minimum, you’ll need some of the following:

ARB Adapter 1/4 NPT(M) JIC-04(M) - 2PK
(These attach the stainless hoses to the compressor air outlet)
https://trailrecon.com/arb-adapter-14-nptm-jic-04m--2pk-740101.html

ARB Remote Hose Coupling Kit
(The right angle couplers in here are useful to connect the hose to the compressor.)
https://trailrecon.com/arb-remote-hose-coupling-kit-171314.html

ARB Hose Coupling Dust Cap
https://trailrecon.com/arb-hose-coupling-dust-cap-740113.html


I’m still in the process of building a bracket to hang the air tank. Right now I just have my stainless air hose routed to the rear of the bed, but ultimately I plan to route it out the front of the bed and connect it to the air tank by the spare tire. Then the air tank will be plumbed to the remote house coupling probably near the bumper. I’ll make another post once I finish up the air tank with additional details.

If I missed anything in the list above, please let me know. I’m also curious if anything has any ideas on ways to improve the design. Hope everyone is having a great week!
 
Last edited:
ARB Install

I decided to install my ARB twin CKMTA12 (https://www.apollo-optics.com/produ...rformance-12-volt-twin-air-compressor-ckmta12) compressor in the bed of my truck. I placed BuiltRight small panels (https://builtrightind.com/products/builtright-industries-bedside-rack-system-small-panel-2015-ford-f-150-raptor-2017-ford-f250 ) at the front of the bed. On the driver side panel, I installed a BlueSea SafetyHub 150 Fuse Block (https://www.westmarine.com/blue-sea-systems-safetyhub-150-fuse-block-11975794.html) that serves as a distribution point for power to anything I install on the back half of the truck.

View attachment 57462

View attachment 57463

View attachment 57464

From there, I ran a 1/0 AWG power cable from the battery on the passenger side of the truck down the engine bay, across the top of the wheel well liner, against the frame, into the frame, inside the frame down the length of the truck, inside the frame through a cross member in the rear, out the frame on the driver side, up between the cab and the bed, into the bed through the oval cap on the lower front wall, and attached it to the power distribution block. I ran the ground cable to the underside of the bed and attached it to a factory ground on the driver side frame next to the spare tire. I did grind away the paint under the terminal to ensure a solid connection. I used dielectric grease on the connection and then sprayed it with a clear sealant after bolting it down to help prevent rust.

View attachment 57465

Here’s the parts I used when putting together the power cables…

35 ft of Kolossus Fleks Kable 1/0 Red Power /Ground Wire
https://www.knukonceptz.com/mobile-...olossus-fleks-kable-10-red-power-ground-wire/

10 ft of Kolossus Fleks Kable 1/0 Black Power/Ground Wire
https://www.knukonceptz.com/search-results/sp/kolossus-fleks-kable-10-black-powerground-wire/

Gold Plated 1/0 Ring Terminal -Red
https://www.knukonceptz.com/sp/gold-plated-10-ring-terminal-red/

Gold Plated 1/0 Ring Terminal - Black
https://www.knukonceptz.com/sp/gold-plated-10-ring-terminal-black-/

KnuKonceptz Dual Wall 1 Inch (1/0 Gauge) Adhesive Lined 3:1 Heat Shrink Tubing - Red
https://www.knukonceptz.com/search-...-gauge-adhesive-lined-heat-shrink-tubing-red/

KnuKonceptz Dual Wall 1 Inch (1/0 Gauge) Adhesive Lined 3:1 Heat Shrink Tubing - Black
https://www.knukonceptz.com/search-...auge-adhesive-lined-heat-shrink-tubing-black/

You’ll need a strong wire cutter as well as a beefy terminal crimped. Here’s what I used:

Klein Tools J63050 Cable Cutter, Journeyman Cable Cutter Cuts Aluminum, Copper and Communications Cable with Shear-Type Jaws

(The cutter above is barely big enough, but it gets the job done if you cut/rotate a little at a time.)

AMZCNC Hand Operated Hydraulic Crimping Hydraulic Cable Lug Crimper 8 US TON 12 AWG to 00 (2/0) Electrical Terminal Cable Wire Tool Kit with 9 Die

(This crimper was awesome - it worked perfectly!!)

I wrapped the power cables in split wire loom and wrapped the ends with tape. I also wrapped a couple loops of tape every couple feet along the loom to ensure it held together well.

5 Rolls Tesa's Most Advanced High Heat Harness Tape 51036 Mercedes, BMW, Audi, VW

3M Scotch Vinyl Electrical Tape Super 88, Premium Grade All-Weather, 3/4 in x 44 ft, 8.5-mil thick, Black, 1 roll

I like to use a little red electrical tape around the end of the positive power cables just to make it clear which cable is positive when doing any maintenance in the future.

Gardner Bender GTPC-550 Electrical Tape, ½ in x 20 ft., Durable, Easy-Wrap, Flame Retardant, 5 Pk, Red, White, Blue, Green, Yellow

A tip to installing the wire into the loom is to use a tool like this…

Electriduct Wire Loom Insertion Tool Set for 3/8" to 2" Conduit Sleeving Installation

Here’s the loom I used for the 1/0 AWG power cables:

ZhiYo 20FT 5/8" Wire Loom Split Tubing Auto Wire Conduit Flexible Cover

Let’s talk fuses for a bit. You’ll need an inline fuse on the power cable as well as fuses for the BlueSea block. Originally, I was going to use a KnuKonceptz ANL fuse inline on the power cable, but I found an easier fuse options that also helped with my batter clutter.

What I found was a 3-way fused bus bar from Mouser.
https://www.mouser.com/ProductDetail/Littelfuse/0FHZ00853-BX?qs=qpJ%2B%2B%2Bdg6p1tph0MWK00pQ==

Then I got this 150A fuse from Mouser to use with the bus bar.
https://www.mouser.com/ProductDetail/Littelfuse/3298150.Z?qs=aGgfWYEhH7lN37SvSGko3g==&countrycode=US&currencycode=USD

To connect the bus bar to the battery post, I had to first add a product from Rugged Rocks to my battery’s positive post.
https://ruggedrocksoffroad.com/power-distribution-terminal-blocks-by-rugged-rocks.html?search=Battery block

Then I screwed 2 threaded, positive battery posts into the block from Rugged. The posts I used were super fancy and purchased from Walmart. :p The set comes with a positive and a negative post, so be sure to buy 2 sets if you also want 2 positive posts to use like I did. (Pos/neg posts are different sizes!)
https://www.walmart.com/ip/2-Pcs-Ba...lts-Positive-Negative-For-Car-Boats/418255379

The Mouser post requires these nuts for you to attach ring terminals to them.
Prime-Line 9094921 Flange Nuts, Class 8 Metric, M8-1.25, Zinc Plated Steel, (10-pack)

Here’s the main fuse you need to use on the BlueSea block for the 2 red power cables that attach from the ARB harness to the power block. These 40A fuses match the rating of the inline fuses that ARB uses.

Blue Sea Systems MIDI or AMI Marine Fuse, 40A, (2) 5251

You’ll also need some standard fuses for anything smaller you connect to the power block (though this ARB install does not need them).

Petutu Blade Car Fuses Assortment Kit 220Pcs –Standard & Mini (2A/3A/5A/7.5A/10A/15A/20A/25A/30A/35A),Car Boat Truck SUV Automotive Replacement Fuses


Another nifty change I made was to not use the ARB-supplied harness for the switch (I only used their power harness). For the switch, I created my own cable/plug that connects directly to the ARB plug on the compressor. One thing to note is that this “switch” wire does 2 things… 1) it signals the relay in the compressor to turn on and 2) it powers the small cooling fan inside the compressor. Since the wire is technically doing more than just signaling the relay, I decided to use a 14 AWG wire for peace of mind when I built my custom wire harness for the switch.

View attachment 57466

View attachment 57467

Here’s the 14 AWG wire I used for my signal wire connected to the upfitter switch:

InstallGear 14 Gauge OFC Primary Remote Wire, 100-feet - Yellow

Wire loom for the signal wire:
ZhiYo 50 FT 1/4” Wire Loom Split Tubing Auto Wire Conduit Flexible Cover | High Temperature Heat Resistant -40F to 257F | Plastic Cover for Electrical Wires & Cables

Insertion tool for the small, 1/4” loom:
Yellow Loom Tool - Cable Insertion for Small Bundles from 1/4" to 3/8"

Here are the parts you need to terminate the 14 AWG wire into a plug that is compatible with the ARB plug.

The plug is a Delphi style plug.

Crimper:
IWISS Weather Pack Crimper Tools for Delphi APTIV Packard Weather Pack Terminals Metri-Pack Connectors for Sealed Terminals

Plug: (You’ll use the male side of this plug that has the purple rubber on it.)
Delphi Metri-Pack 150 Series 3-Way Connector w/16-18 AWG Sealed Waterproof Set

The plug has space for 3 wires, but the only wire we care about is the center pin wire. This is the “signal” wire that is used by the ARB compressor. (It’s equivalent to the purple wire on the ARB switch harness). Since we will not be using the 2 outside pins, seal off your connector by getting 2 rubber plugs to insert:

https://www.customconnectorkits.com/12059168/


That’s all you need to build your own, clean switch harness that is compatible with the factory ARB plug. Then, when you run the yellow switch wire to the upfitter switch, I like to connect it using JRready DTHD connectors. These allow you to easily remove or swap accessories with each of the upfitter switches.

View attachment 57468

I used heat drink butt connectors with solder inside them to easily connect the yellow wire to my upfitter wire.

Limited-time deal: TICONN 250 Pcs Solder Seal Wire Connectors, Heat Shrink Butt Connectors, Waterproof and Insulated Electrical Wire Terminals, Butt Splice (250PCS)

To get a good heat shrink, I used a heat gun from Harbor Freight with a metal adapter on the end to concentrate the heat around all sides of the connector.

Then I shrank heat shrink tubing on top of the connection.
Wirefy Heat Shrink Tubing Kit - 3:1 Ratio Adhesive Lined, Marine Grade Shrink Wrap - Industrial Heat-Shrink Tubing - Black 180 PCS

Then I wrapped it in tape and wire loom.

Here’s the connectors I chose to use for this purpose. I really like them!

JRready ST6286 1 Pin DTHD Connector 4 Sets,IP67 Waterproof Single Terminal Connectors for Heavy-duty Applications,Contact Size 12 Crimp Wire Gauge 12-14AWG,25A

4-way crimper for the above plugs:
IWISS Closed Barrel Crimper 4 Way Indent,8 Impression Type for Deutsch Solid Contacts gage 12 (IWD-12)

Bonus item… my favorite zip ties for automotive and outdoor projects:
TR Industrial Multi-Purpose UV Resistant Black Cable Ties, 8 inches, 100 Pack


For the airline hoses, I got a bunch from Northridge 4x4 as well as Trail Recon.

https://www.northridge4x4.com/search?q=arb+hose
https://trailrecon.com/search?query=Arb-hose


At a minimum, you’ll need some of the following:

ARB Adapter 1/4 NPT(M) JIC-04(M) - 2PK
(These attach the stainless hoses to the compressor air outlet)
https://trailrecon.com/arb-adapter-14-nptm-jic-04m--2pk-740101.html

ARB Remote Hose Coupling Kit
(The right angle couplers in here are useful to connect the hose to the compressor.)
https://trailrecon.com/arb-remote-hose-coupling-kit-171314.html

ARB Hose Coupling Dust Cap
https://trailrecon.com/arb-hose-coupling-dust-cap-740113.html


I’m still in the process of building a bracket to hang the air tank. Right now I just have my stainless air hose routed to the rear of the bed, but ultimately I plan to route it out the front of the bed and connect it to the air tank by the spare tire. Then the air tank will be plumbed to the remote house coupling probably near the bumper. I’ll make another post once I finish up the air tank with additional details.

If I missed anything in the list above, please let me know. I’m also curious if anything has any ideas on ways to improve the design. Hope everyone is having a great week!
Great info!!! Did you use the factory bracket that comes on the ARB compressor to attach to the Builtright panel? I think those are M6 weldnuts, correct? My plan was to bolt through the panel into the weldnuts on the ARB bracket... maybe you found a better way, though??
 
Great info!!! Did you use the factory bracket that comes on the ARB compressor to attach to the Builtright panel? I think those are M6 weldnuts, correct? My plan was to bolt through the panel into the weldnuts on the ARB bracket... maybe you found a better way, though??
Haha I have to go look. I don’t remember what I ended up doing. 🙈

I definitely used the ARB bracket but don’t recall the specific bolt hardware I used.
 
Haha I have to go look. I don’t remember what I ended up doing. 🙈

I definitely used the ARB bracket but don’t recall the specific bolt hardware I used.
I am going to follow your ARB install pretty much completely - five stars for the documentation you provided. I hope to have this done before fall.
 
I am going to follow your ARB install pretty much completely - five stars for the documentation you provided. I hope to have this done before fall.
Sweet. Let me know the total cost of the project. I’ve been afraid to look… 😱🫣🤣
 
DF2B73E8-4764-451B-B72F-11939EFBDE1A.webp

Added custom brackets for rear LEDs! All bolt on using factory bolts! Can you see them? 😄 More to come!
 
Alright, I had these warnings appear around 100 miles into the drive on my new 2022.


View attachment 52909
View attachment 52908

Had the truck at Covert in Austin, TX this past week. They were stumped and had to call the Ford hotline. Ford said to replace a “bracket”. I’m not sure which one. Will try to update tomorrow if I find out.

The bracket didn’t fix anything. Covert called Ford again, and they said to replace the sensor. (I assume the adaptive cruise sensor) This fixed the problem!
It’s the 21 letting you know you should have kept it. 😆
 
Huge upgrade!! I finished installing the new GMRS radio from Midland, the MXT575! It is AWESOME!! Here's a video showing how easy the install is on our super duties! It fits like a glove in the glovebox... :cool:

Spoiler alert: the official August group buy starts Monday... save some $$$ and get the same package I show you in this video.

 
Got the truck back from Mike at Linex of Round Rock. I love the work he and Dan do at that shop. Great, honest guys.

Linex sprays come in standard, premium, and platinum. Premium is standard with a UV protective top coat. Platinum is a different chemical called XS-350 and is 300% stronger than the standard chemical! At $940 it’s not cheap, but I think it’s worth it on these trucks.

View attachment 48859View attachment 48860View attachment 48861View attachment 48862View attachment 48863View attachment 48864
Would you by chance know how the options compare to the factory spray liner?
 
Back
Top Bottom