22 Black Bear 🐻 Build

Got the Rough Country 40-Inch Chrome Series White DRL LED Light Bar installed over the weekend! I used the hardware it came with to mount directly to my bumper. It was fairly easy to drill 2 holes for the bolts and affix a nut on the bottom by popping off the front plastic trim pieces. I had to use a couple wobble extensions to get to the nut, but it was pretty easy. Only mistake I made is that the light bar is pointed slightly down (not bad, but the perfectionist in me is annoyed) because I installed the light bar while my truck was parked on my steep driveway... oops.

I know guys that talk about how cheap Rough Country is and how they'll never have it on their trucks... I think I agree when it comes to suspension parts, but I'm happy to try this light for less than $200 and see how long it lasts. It's MUCH brighter than even the factory OEM High Beam LEDs. And for anyone that asks, I leave the plastic cover on the light bar during normal driving in town. The intent of a light like this is for driving off-road or in rural areas/parks with no oncoming traffic.

A couple other install notes... I was able to slide the provided wiring harness through the firewall grommet on the driver side of the engine bay. It was plenty long. Had to cut a small slit in the grommet. Be careful not to nock out the grommet when pushing your wire through.... my roommate and I did, and we had to spend 30 min working to get the grommet back into it's original position.

As for power, most of my accessories are attached to the passenger battery. Since I was routing the power harness through the driver side of the truck, I decided to get power from the driver side battery. I drilled a hole in the positive terminal and added a small bolt/nut to attach the ring from the harness. The negative/ground on the frame was a bit hard to remove due to clearance, so it was easier to just connect the negative side of the harness directly to the battery since the negative terminal already had a post on it.


View attachment 169587View attachment 169588View attachment 169589View attachment 169590
Legmar how has this light bar been holding up for you? When looking at these and pillar pods I’ve pricing things out and I’m wondering how this has held up. Seems like great value. The blackout would look good on my black two tone KR. Seals held up? Any regrets? Almost thinking for cost could replace after few years and still be well under cost of other bars lol.
 
Legmar how has this light bar been holding up for you? When looking at these and pillar pods I’ve pricing things out and I’m wondering how this has held up. Seems like great value. The blackout would look good on my black two tone KR. Seals held up? Any regrets? Almost thinking for cost could replace after few years and still be well under cost of other bars lol.
My thoughts exactly! It’s been doing great! I even take it through the automated car wash occasionally. I’m pretty happy with it. I’d buy it again for sure!

My only regret is I have it angled too low. Need to find the time to adjust it. 🤪
 
My thoughts exactly! It’s been doing great! I even take it through the automated car wash occasionally. I’m pretty happy with it. I’d buy it again for sure!

My only regret is I have it angled too low. Need to find the time to adjust it. 🤪
Are the brackets solid? They just mount to plastic piece correct?
 
Are the brackets solid? They just mount to plastic piece correct?
The bracket seems very solid. It mounts on top of the plastic, yes, but under the plastic is metal. I had to drill through the plastic and through the metal bumper to get my mounting holes ready.

IMG_4335.webp
IMG_4333.webp
 
Took advantage of the first Saturday that felt a bit more like fall weather in Texas, and I installed the ditch light kit from Subtle Design (great product, @BroncOh!)

IMG_6725.webp

IMG_6720.webp

IMG_6703.webp


The driver side took me 3 hours.
The passenger side took me just under 1 hour.

My biggest tip is to install the grommet first into the hole you drill in the mirror, and then shove the Baja Designs S2 cable through the grommet/hole. If you try to get the grommet shoved into the hole when it’s already on the cable, you’re gonna need an extra dose of patience. 🤪

IMG_6702.webp


I love the outcome of the product after the install! I did a little drive in the dark, and the combination of the S2s, my KC Hilites pods, and my Rough Country curved lightbar on the bumper make for a fantastic forward display of light in dark places!

Here’s a shot of the factory plug before the install.
IMG_6707.webp


Here’s a shot of the factory plug after the install.
IMG_6712.webp
 
Last edited:
Took advantage of the first Saturday that felt a bit more like fall weather in Texas, and I installed the ditch light kit from Subtle Design (great product, @BroncOh!)

View attachment 225149
View attachment 225150
View attachment 225151

The driver side took me 3 hours.
The passenger side took me just under 1 hour.

My biggest tip is to install the grommet first into the hole you drill in the mirror, and then shove the Baja Designs S2 cable through the grommet/hole. If you try to get the grommet shoved into the hole when it’s already on the cable, you’re gonna need an extra dose of patience. 🤪

View attachment 225152

I love the outcome of the product after the install! I did a little drive in the dark, and the combination of the S2s, my KC Hilites pods, and my Rough Country curved lightbar on the bumper make for a fantastic forward display of light in dark places!

Here’s a shot of the factory plug before the install.
View attachment 225153

Here’s a shot of the factory plug after the install.
View attachment 225154
Love it man, even completing the mods with a forum shirt on. Next level!
 
It's been a hot minute since I've had time for some upgrades! Feels good to be back at it!! I was gifted the Banks cold air intake as well as the AMP Bed Step 2's for both sides of the cab! I purchased the Banks rear diff cover during the Forum's Group Buy a long time ago!!
IMG_3482.webp

IMG_3481.webp

IMG_3480.webp

IMG_3478.webp

IMG_3477.webp

IMG_3476.webp

IMG_3479.webp


The only issue I've had is that the oil appears low in the sight glass on the diff cover. The instructions from Banks specify that the oil should be halfway up the glass. I have a message in to Banks right now and will report back what they say. I used their oil kit they sent with the cover, so it presumably should have been adequate.

IMG_3474.webp
 
It's been a hot minute since I've had time for some upgrades! Feels good to be back at it!! I was gifted the Banks cold air intake as well as the AMP Bed Step 2's for both sides of the cab! I purchased the Banks rear diff cover during the Forum's Group Buy a long time ago!!
View attachment 248152
View attachment 248153
View attachment 248154
View attachment 248155
View attachment 248156
View attachment 248157
View attachment 248158

The only issue I've had is that the oil appears low in the sight glass on the diff cover. The instructions from Banks specify that the oil should be halfway up the glass. I have a message in to Banks right now and will report back what they say. I used their oil kit they sent with the cover, so it presumably should have been adequate.

View attachment 248159
It's worth mentioning that all these goodies were installed at Thor Offrroad! I was especially excited to work with their shop because they are officially the first authorized retailer of Legmar products!!
They are carrying stock of the Legmar Dual Baja Designs S2 rear bumper light brackets for 23+ Super Duties and showcasing them on their display! Pretty pumped about that!! 😎


 
They are carrying stock of the Legmar Dual Baja Designs S2 rear bumper light brackets for 23+ Super Duties and showcasing them on their display! Pretty pumped about that!! 😎
I saw them when I picked up my truck and said hey I know that guy!
 
I saw them when I picked up my truck and said hey I know that guy!
No way! How cool!! What were you getting done?
Never mind, just found your thread - bro, the carli pathfinder is on my future dream list! That's awesome - can't wait to see it in person on your truck!
 
Took advantage of the first Saturday that felt a bit more like fall weather in Texas, and I installed the ditch light kit from Subtle Design (great product, @BroncOh!)

View attachment 225149
View attachment 225150
View attachment 225151

The driver side took me 3 hours.
The passenger side took me just under 1 hour.

My biggest tip is to install the grommet first into the hole you drill in the mirror, and then shove the Baja Designs S2 cable through the grommet/hole. If you try to get the grommet shoved into the hole when it’s already on the cable, you’re gonna need an extra dose of patience. 🤪

View attachment 225152

I love the outcome of the product after the install! I did a little drive in the dark, and the combination of the S2s, my KC Hilites pods, and my Rough Country curved lightbar on the bumper make for a fantastic forward display of light in dark places!

Here’s a shot of the factory plug before the install.
View attachment 225153

Here’s a shot of the factory plug after the install.
View attachment 225154
I have these sitting on my car lift. I need to get after it. Seems pretty straight forward, I guess I am worried about hamfisting it somehow.
 
I have these sitting on my car lift. I need to get after it. Seems pretty straight forward, I guess I am worried about hamfisting it somehow.
It’s not too bad! Hit me up if you run into any snags or have questions!
 
Sounds good, brother. I want these on before hunting season so when I navigate into the woods early in the am I don't run over a tree or head into brush. The OEMs just don't cut it, and @BroncOh did a slick job. I need to get my butt in gear and get them on!
 
I have these sitting on my car lift. I need to get after it. Seems pretty straight forward, I guess I am worried about hamfisting it somehow.
If you need assistance in hamfisting, send me a DM!
 
Back
Top Bottom