Good sale going on at Method

I really need some bead grips but I have been waiting on some more promising designs for 18"
I haven't decided if I'm a believer in the bead-grip thing. I've had Vision Manx forged and now have KMC Mesa Forged; both with their bead grip stuff. Not to say is Doesn't work, but i popped a bead drifting my Ram on the KMC beadgrip at 20psi (still a relatively high pressure) and almost rolled my truck. This is zero fault of the product and 100% on me as I'm pushing a 600hp/1,300tq 9,200lb. truck sideways on a tacky surface, I need to be on beadlocks but i thought the pressure was high enough to maintain sidewall integrity under the limited traction situation.

In my experience, the middle ground of beadgrip is playing with fire if you plan to use it on a heavy truck. If you're toeing the line between standard and beadlocks, probably better to over-correct than get too confident in the partial solution as you'll find it insufficient at the worst possible time. Plus, you almost always destroy tires when you swap them out - not an issue unless you go through tires at the rate i do, but worth mentioning if you're a guy that swaps out tires with some tread-life to throw them on marketplace.

Of the beadgrips, there's no better looking wheel than the KMC Forged Mesas - i have them on both rigs and love them; just can't treat them like beadlocks if you drive as dumb as I do!
 
Yea im pretty sure they would work with my current setup ive got quite a bit of clearance due to trimming I've done. Was just worried about 38x13.5 having the right offset to prevent any rubbing from the extra height and width. It looks like it should be ok as @thatdood says he has a carli 38s with a +18 offset. If needed I can always leave on my 3/8" bora spacers to give a little more clearance from the radius arm and sway bar.

Also keep in mind I run the 4.5/5.5in lift not the 2.5/3.5 level
 
I haven't decided if I'm a believer in the bead-grip thing. I've had Vision Manx forged and now have KMC Mesa Forged; both with their bead grip stuff. Not to say is Doesn't work, but i popped a bead drifting my Ram on the KMC beadgrip at 20psi (still a relatively high pressure) and almost rolled my truck. This is zero fault of the product and 100% on me as I'm pushing a 600hp/1,300tq 9,200lb. truck sideways on a tacky surface, I need to be on beadlocks but i thought the pressure was high enough to maintain sidewall integrity under the limited traction situation.

In my experience, the middle ground of beadgrip is playing with fire if you plan to use it on a heavy truck. If you're toeing the line between standard and beadlocks, probably better to over-correct than get too confident in the partial solution as you'll find it insufficient at the worst possible time. Plus, you almost always destroy tires when you swap them out - not an issue unless you go through tires at the rate i do, but worth mentioning if you're a guy that swaps out tires with some tread-life to throw them on marketplace.

Of the beadgrips, there's no better looking wheel than the KMC Forged Mesas - i have them on both rigs and love them; just can't treat them like beadlocks if you drive as dumb as I do!
I have always wondered the same thing and while beadlocks do not fully guarantee against losing a bead unless you're running dual beadlocks (both the inside and outside), I was skeptical on real life use of bead grips on heavier rigs.

Most testing is done on lighter-duty rigs, where beadgrips generally perform as intended, but doubling the weight presents a different challenge and may not yield the same results.

20 pounds is nothing on standard rims much less beadgrips.

I suppose I see no benefit if I already tear through trails on 14-18 pounds with extreme caution.
 
Back
Top Bottom