Ford Emblems

Suncoast said:
I believe you could just install the square piece with the washer like normal. It would just never open if there’s no fluid attached to it.
Click to expand...
Sure if you wanna buy the washer too
 
Ole703 said:
Front emblem part number available in first post. Just an update.
Click to expand...
So that’s the one on your 26? It has no schnozzle hole. Or did you snap in the blank cover?
 
The grill has to come off.
Plastic push rivets pop up and out to release top cover. Four or so 10mm bolts below the cover. Two 10mm bolts in the grill beneath two plastic covers that pop out in the lower portion of the grill. Then just snap clips so pull from the top of the grill forward (away from the headlights)

It is helpful to have a second person to hold the grill. So you can get the front camera unplugged. Three 10 mm crappy metal self tapping nuts unthread to release front emblem.

Lay a towel or packing blanket on top bumper to avoid scratching paint on bumper.
 
Last edited:
On the two bottom bolts, are they on the front or the back of the grill?
 
Ole703 said:
The part number in the first post. Has no schnozzle hole. It was a fully intact emblem. Camera hole only. Yes for a 2026.
Click to expand...
Thank you sir! I’m going to have to order one for mine. The hole was what was holding me back.
 
ramv said:
On the two bottom bolts, are they on the front or the back of the grill?
Click to expand...
They are forward facing of the grill. Have two small plastic covers over them. One on each side passenger and driver. Near the bottom of each headlight.
 

Attachments

  • IMG_0454.webp
    IMG_0454.webp
    282.3 KB · Views: 18
Thank-you!
 
Ole703 said:
The grill has to come off.
Plastic push rivets pop up and out to release top cover. Four or so 10mm bolts below the cover. Two 10mm bolts in the grill beneath two plastic covers that pop out in the lower portion of the grill. Then just snap clips so pull from the top of the grill forward (away from the headlights)

It is helpful to have a second person to hold the grill. So you can get the front camera unplugged. Three 10 mm crappy metal self tapping nuts unthread to release front emblem.

Lay a towel or packing blanket on top bumper to avoid scratching paint on bumper.
Click to expand...
Not sure why you quoted me I’ve had the grills off these trucks several times not sure if that was meant for kingranch
 
We shall see, they are custom stickers, and each piece has to be applied. The original emblem has to be cleaned and prepped. Can choose different colors and options. I will post up once I get them in. Thought they were worth a try.
 
I LIKE this a lot and very reasonably priced. I think I'm gonna pull the trigger on a full black out once I hear what your experience is.
 
Ole703 said:
The grill has to come off.
Plastic push rivets pop up and out to release top cover. Four or so 10mm bolts below the cover. Two 10mm bolts in the grill beneath two plastic covers that pop out in the lower portion of the grill. Then just snap clips so pull from the top of the grill forward (away from the headlights)

It is helpful to have a second person to hold the grill. So you can get the front camera unplugged. Three 10 mm crappy metal self tapping nuts unthread to release front emblem.

Lay a towel or packing blanket on top bumper to avoid scratching paint on bumper.
Click to expand...
Thank you for the help. I will be ordering paint matched LED light. This calmed my nerves.
 
Finally got the rear emblem that’s blacked out with a chrome outer perimeter. Doesn’t match my smoked front. But it’s what I could find from oem parts.

Pictures and part number in the first post.
 
You must log in or register to reply here.

Tremor Forum Fav 👍

Rightcar Solutions Silicone License Plate Frames Rightcar Solutions Silicone License Plate Frame - Grab one through Amazon!

Tremor Forum Photos

Latest Discussions

Back
Top Bottom