What’s on your Black Friday shopping list?

Be careful with that 4 pack, those are all the centered version. The front pockets on our trucks are the offset fitment and the rears are centered.

My truck has the Ford angled rear ones but nothing up front. Wish Bullring would/could make and angled offset version for the front. But I guess the straight offset version will have to do. I have been meaning to get some for the front.
oh interesting, i thought it was just how you wanted the rings to align - so it's based on how they mount?
 
As much as I want some reverse lighting. It just isn't in the budget this year.
a few smaller purchases on the radar.
Genpro 10x1 for overnight charging on the truck.
And some sort of wifi extender. ATT just installed fiber at home. And where they put the router sucks. It won't reach my garage. I plan to use a 2x1 smart plug for the battery charger/block heater. So I need to extend wifi to driveway for controlling it.
Wifi Extender
If anyone has suggestions, I am all ears. This wifi stuff is above my pay grade. 2nd benefit is when people come to town and crash in our RV. This extender should hopefully give a better signal in the RV for TV etc.
I installed the Baja designs reverse kit and love it. Wired them to my upfitter.
 

Attachments

  • IMG_5086.webp
    IMG_5086.webp
    234.9 KB · Views: 6
  • IMG_5087.webp
    IMG_5087.webp
    332 KB · Views: 6
ok - i had to grok this...

Factory stake pockets​

The openings in the bed rails are straight / vertical. They are rectangular holes that go straight down into the rail. They are not angled.

What does vary:

  • Offset position — On many 6¾-ft Super Duty beds the front and/or middle stake pockets sit slightly off-center (not perfectly centered in the rail). The rear pockets are usually centered.
  • Aftermarket “angled” hardware — Products like BullRing make D-rings that are angled ~35° for a better strap pull. The pocket itself is still straight; only the ring is angled.

Key measurements (current Super Duty 6.75-ft bed)​

SpecValue
Floor length81.9 in
Max inside width66.9 in
Width between wheel wells50.5 in
Bed depth21.1 in
Stake pocket styleStraight vertical openings

Older forum data (pre-2017) listed pocket openings around 1.7–2.3 in, but the current aluminum beds use the same straight pocket design.

Visual verification​

Here are clear references so you can compare to your truck:
og:image
Super Duty 6.75-ft bed diagram — shows overall bed dimensions (stake pockets sit in the top rails).
Amazon.com
BullRing offset stake-pocket example — shows the pocket opening and notes “misaligned / offset” rail caps common on short-bed Super Duties.
Amazon.com
Angled vs. straight D-ring hardware — the ring is angled; the pocket it drops into is still straight.
Stage 3 Motorsports
Putco stake-pocket rack on 6.75-ft Super Duty — shows the pockets used as straight mounting points.

Quick check on your truck​

  1. Pop a plastic stake-pocket cap (if present).
  2. Look straight down into the hole — it should be a vertical rectangular opening.
  3. Check whether the front/middle pockets sit dead-center in the rail or slightly forward/rearward (offset).
The pockets themselves are straight. Any “angled” description you see is about the accessory hardware, not the factory mounts.
 
oh interesting, i thought it was just how you wanted the rings to align - so it's based on how they mount?
Its due to the plastic cut out on the rail being offest from the pocket. On the Superduty Trucks generally the rear is centered and the front and middle (8ft bed) are offset like below. Why Ford does this I couldn't tell you.

1795194492078.webp
 
Just checked mine - all straight

IMG_0548.webp IMG_0547.webp
 
Last edited:
FYI, in case you wanted a smaller capacity pan, the gas version of the trans pan also works in the diesel. I’m not sure if the 24 is as tricky as the 26 in regards to the cooler in front of the pan, but see my tips here:

Thanks, I’m on board with the 7.3 pan. Thanks for the write up.
 
I am looking for the diode dynamics dual color fog lights. Haven’t seen a sale on them yet.
 
I am looking for the diode dynamics dual color fog lights. Haven’t seen a sale on them yet.
@Nick@ApolloOff-Road has DD listed here.
Are you looking for dual color? Or backlit?
 
Just checked a Chevy in the parking lot. All of them are gaaaaaayyyyyyyyyy.
I wish Ford would do away with the plastic caps on the rails. Or at least do it so they don’t look like an abortion when you take them off. I’d just LineX them if I had a choice.
 
I am looking for the diode dynamics dual color fog lights. Haven’t seen a sale on them yet.

@Nick@ApolloOff-Road has DD listed here.
Are you looking for dual color? Or backlit?

Are these what you are looking for?

Didnt know they made these. Might have to nab a set myself. Always wanted Yellow fogs for this truck (like I put on all my vehicles) but didnt want to pay $1000+ for the BD pods and bezzle.
 
The rail image I sent was from their listing which is for an 11-16 SD.

But let me know how it goes. I don't feel like pulling my Tonneau cover right now to check mine. But at least they went on sale and Amazon is easy to return stuff.
yeah, i'm doing mine before I put on the tonneau cover for sure this time!
 
I wish Ford would do away with the plastic caps on the rails. Or at least do it so they don’t look like an abortion when you take them off. I’d just LineX them if I had a choice.
Sort of on/off subject.... Why the hell am I seeing tundras running around with rectangular holes in the front of their hoods?! Is there a stupid cap there that has reached the end of its lifecycle and fallen off of multiple vehicles?!?!🤷🤣🤣
 
I wish Ford would do away with the plastic caps on the rails. Or at least do it so they don’t look like an abortion when you take them off. I’d just LineX them if I had a choice.
Also, just take them off and cover them with aluminum diamond plate🤷 😜
 

Latest Discussions

Back
Top Bottom