7.3 (Godzilla) headers

Sure, i did some youtube shorts of it


WOW,
That sounds amazing
I have the Legend exhaust, waiting at home for me next year I plan to do the Long Tube headers. I have a 2023 7.3 Godzilla, can this be done without a Tune? I am concerned about retaining the factory warranty
 
WOW,
That sounds amazing
I have the Legend exhaust, waiting at home for me next year I plan to do the Long Tube headers. I have a 2023 7.3 Godzilla, can this be done without a Tune? I am concerned about retaining the factory warranty
I added 02 spacers and did not get a CEL, no tune. But either way, if you have something catastrophic happen, the dealer could still be a pain about the headers.
 
I added 02 spacers and did not get a CEL, no tune. But either way, if you have something catastrophic happen, the dealer could still be a pain about the headers.
The Godzilla may have better fuel management and/or more range with fuel trims, but on my old F150 it was running really lean before I had it tuned when I added LT headers... like, lean enough that you might cause engine damage if you ran it under high load. Kooks recommended strongly against running them without a tune on that truck as even with a tune the stock injectors were at really high duty cycles at WOT... again no idea if this is an issue with the 7.3, it's probably better suited than that old 3V turd was. Still, headers is a lot of money to spend just to get the sound and not have it tuned to actually get any meaningful performance out of them.
 
Who says you wont get any gains without a tune? Either way, there are no tunes available for the 23s yet, I do plan on tuning it. Or throwing a whipple on it that comes with a tune....
 
Who says you wont get any gains without a tune? Either way, there are no tunes available for the 23s yet, I do plan on tuning it. Or throwing a whipple on it that comes with a tune....
Key operative word in my post was "meaningful" gains... you probably picked up single digit HP/TQ from installing headers with no tune, but yeah you mostly just picked up a bunch of noise and are nowhere near optimized without a tune. You are also potentially (likely) running lean because the computers on most non-performance cars dont have enough range to adjust fuel trims for the added airflow/scavenging from the headers (hence, also, why you wont pick up much power).
 
Last edited:
The high flow cats alone will net positive gainz, let alone the other benefits of less restriction as well as scavenging.

Im not discounting the benefits of a tune at all, but saying long tubes on a big block won't make power is downright ridiculous.
 
Last edited:
Aside from getting these to "sound better" I have yet to see anyone post numbers on their install. I know SW well. They make great products (I live in Ohio and used them for purchasing tubes years ago for my shop). But the one thing that still cracks me up is that no one ever tests this stuff on a dyno. For all the work and cost that goes into this, its all about spending thousands of dollars to get better sound. Until I see number beyond it made 10HP, I think this is a waste.
 
Aside from getting these to "sound better" I have yet to see anyone post numbers on their install. I know SW well. They make great products (I live in Ohio and used them for purchasing tubes years ago for my shop). But the one thing that still cracks me up is that no one ever tests this stuff on a dyno. For all the work and cost that goes into this, its all about spending thousands of dollars to get better sound. Until I see number beyond it made 10HP, I think this is a waste.
A) if all you care about is peak numbers, youre doing it wrong
B) I live in east bumfuck Maine, where the hell am I going to pop in and do a dyno pull?
 
Aside from getting these to "sound better" I have yet to see anyone post numbers on their install. I know SW well. They make great products (I live in Ohio and used them for purchasing tubes years ago for my shop). But the one thing that still cracks me up is that no one ever tests this stuff on a dyno. For all the work and cost that goes into this, its all about spending thousands of dollars to get better sound. Until I see number beyond it made 10HP, I think this is a waste.
I believe 5 Star Tuning picked up I think 30ish HP and maybe 35-40 FT/LBS torque with ARH headers on their Godzilla shop truck (Tuned) if memory serves correct (they did a Youtube video on it). Palm Beach Dyno got similar results although harder to parse out because they baselined the truck and then did a tune, headers and a fully custom dual 3" exhaust all at the same time so HP was I think closer to 50 all in (again there's a youtube video for anyone who cares).

But yeah, beating a dead horse here, you'd be lucky to pick up high single digits on a modern non-performance car running just headers with no tuning or supporting mods, and you'll be running really lean because you've added a bunch of extra airflow and you haven't added more fuel to account for it (because the stock computer isnt programmed to compensate for that kind of a change).

ETA: I vaguely remember the 5 Star guys even joking about the biggest gain in performance you will see on this kind of mod for these trucks is just losing the weight of the factory parts :ROFLMAO:
 
Last edited:
I believe 5 Star Tuning picked up I think 30ish HP and maybe 35-40 FT/LBS torque with ARH headers on their Godzilla shop truck (Tuned) if memory serves correct (they did a Youtube video on it). Palm Beach Dyno got similar results although harder to parse out because they baselined the truck and then did a tune, headers and a fully custom dual 3" exhaust all at the same time so HP was I think closer to 50 all in (again there's a youtube video for anyone who cares).

But yeah, beating a dead horse here, you'd be lucky to pick up high single digits on a modern non-performance car running just headers with no tuning or supporting mods, and you'll be running really lean because you've added a bunch of extra airflow and you haven't added more fuel to account for it (because the stock computer isnt programmed to compensate for that kind of a change).

ETA: I vaguely remember the 5 Star guys even joking about the biggest gain in performance you will see on this kind of mod for these trucks is just losing the weight of the factory parts :ROFLMAO:
Whats your scientific reasoning that long tube 1 7/8" individual headers dont make power over log style manifolds, go ahead, im curious.
 
Whats your scientific reasoning that long tube 1 7/8" individual headers dont make power over log style manifolds, go ahead, im curious.
This has already been explained in several posts (all 3 of mine for starters) but since you seem a little slow (or are just deliberately misreading what people are writing) I’ll try and break it down into simpler terms for you, here goes:

Engines need a specific amount of air and fuel to go boom... if you add more air (headers) but not more fuel (tune) no get more boom… simple?

Removing restrictions or increasing scavenging doesn’t make more power, it simply allows the engine to pump more air, if you don’t combine that with more fuel you won’t make more power, it really is that simple. The factory computer will trim this out to a degree which is why you will get “some” additional power (notice i didn’t say “none”), most likely single digits, depending on how much range the stock fuel tables are able to adjust for, but that’s it until you tune it to add more fuel. Until then you are still going to be running lean, which is not exactly a good thing.
 
Last edited:
I believe 5 Star Tuning picked up I think 30ish HP and maybe 35-40 FT/LBS torque with ARH headers on their Godzilla shop truck (Tuned) if memory serves correct (they did a Youtube video on it). Palm Beach Dyno got similar results although harder to parse out because they baselined the truck and then did a tune, headers and a fully custom dual 3" exhaust all at the same time so HP was I think closer to 50 all in (again there's a youtube video for anyone who cares).

But yeah, beating a dead horse here, you'd be lucky to pick up high single digits on a modern non-performance car running just headers with no tuning or supporting mods, and you'll be running really lean because you've added a bunch of extra airflow and you haven't added more fuel to account for it (because the stock computer isnt programmed to compensate for that kind of a change).

ETA: I vaguely remember the 5 Star guys even joking about the biggest gain in performance you will see on this kind of mod for these trucks is just losing the weight of the factory parts :ROFLMAO:
At least you've provided some reference. Better sound....to each his own. But for parting ways with thousands of dollars without any numbers as is frequently the case with SW parts.....to me, is a joke. Parts should offer some benefit or value. If 30+ is true I'd say that's a worth the time. Particularly with the torque increases that are super important to moving these big heavy trucks.
 
Theres no tune for the 23s yet. I have 02 anti foulers installed and havent got a cel yet.

How well is this still working for you? Any CELs overtime? Does you truck still pass emissions in your state if applicable? Nys requires yearly emissions test with the yearly inspection.
 
How well is this still working for you? Any CELs overtime? Does you truck still pass emissions in your state if applicable? Nys requires yearly emissions test with the yearly inspection.
Still no CELs

Haven't got an inspection yet.
 
How well is this still working for you? Any CELs overtime? Does you truck still pass emissions in your state if applicable? Nys requires yearly emissions test with the yearly inspection.
The Stainless Works headers are federally legal with EPA approved catalytic converters so you will not have any issues passing emissions. Feel free to send me a PM if you'd like to chat more about them. We have them in stock and ready to ship.

Stainless Works 2020-24 F-250/350 7.3L Long Tube Header Kit FT220188HCAT
 
CF3ENhf.jpg
 
Back
Top Bottom