What did you do to your Tremor today?

also installed the grill cover

Yokohama Geolandar A/T G015's in stock LT285/75R18 size are scheduled to be installed Thursday.

Do you have photo of the grill cover on, curious how it looks fully installed.

My G015s are being mounted as well, i decided to road force balance them from the get go. Will install them myself over the weekend. I took a risk on 12.5s vs tremor size, hopefully they will clear the sway bar, it’s my only concern. But given that they are going on an 8 inch rim, the true tire width is <12.
 
Do you have photo of the grill cover on, curious how it looks fully installed.

My G015s are being mounted as well, i decided to road force balance them from the get go. Will install them myself over the weekend. I took a risk on 12.5s vs tremor size, hopefully they will clear the sway bar, it’s my only concern. But given that they are going on an 8 inch rim, the true tire width is <12.
I meant to take a photo and forgot! I'll snag one tomorrow & post it in the evening.
 
Put Les Schwab Open Range A/T on, and what road noise and ride difference. Should have done this 34,000 miles ago.

Going to put the Good Years on the 72’ F250
 
Did you wrap the door trim or is were those chrome strips replaced with black ones? If replacements, do you know the part numbers?
I wrapped them! It’s probably the easiest thing I have done. You can buy 2” 3m vinyl on Amazon for 20 bucks. It comes with everything you need. It just takes a little practice and patience. I enjoy the project. I will most likely redo everything as there is a learning curve. Specifically the window trim you could knock out in a hour or so. Just watch a couple YouTube videos first.
 
Did you go with the BMC Hitch Bar lights? I added them with the Rigid lights and it's phenomenal.
I went with F150LED lights - they have a clever bracket that uses a rear bumper torx screw for mounting - cost was like $249 for them, and I also purchased the extended harness so I can use an upfitter instead of reverse only.
 
I wrapped them! It’s probably the easiest thing I have done. You can buy 2” 3m vinyl on Amazon for 20 bucks. It comes with everything you need. It just takes a little practice and patience. I enjoy the project. I will most likely redo everything as there is a learning curve. Specifically the window trim you could knock out in a hour or so. Just watch a couple YouTube videos first.
Is it wrap on the door handles as well?
 
Do you have photo of the grill cover on, curious how it looks fully installed.

My G015s are being mounted as well, i decided to road force balance them from the get go. Will install them myself over the weekend. I took a risk on 12.5s vs tremor size, hopefully they will clear the sway bar, it’s my only concern. But given that they are going on an 8 inch rim, the true tire width is <12.
@Alpoba and for anyone else who may be curious, here's a snap of the grille cover that came with my Tremor. Decently thick vinyl looking feeling material, and the peephole for the front camera is a nice touch Not difficult to install, two double sided sheets of installation instructions. Having done it once now, it should take me half the time next installation.
 

Attachments

  • Tremor_Sports_Bra.jpg
    Tremor_Sports_Bra.jpg
    314.8 KB · Views: 103
@Alpoba and for anyone else who may be curious, here's a snap of the grille cover that came with my Tremor. Decently thick vinyl looking feeling material, and the peephole for the front camera is a nice touch Not difficult to install, two double sided sheets of installation instructions. Having done it once now, it should take me half the time next installation.

Thanks for sharing, it's nice to see how it looks installed. I received one of these with my truck but it's still in the package as I will likely never need it lol.
 
Did a mod I forgot to do after I deleted the pull rods for all the doors. Took @Lunch Box 's idea and put a Hooves twist on it. I used a Christmas tree push pin from the Harbor Freight push pin assortment, in addition to a 3D printed TPU grommet while removing the original OEM bezel portion on the door. Low profile and fits snugly.

This prevents passengers from putting trash in doors, such as drinking straw wrappers, etc. Just wanted to be proactive. Also looks better of course.

Attaching the STL print files here at the bottom of this post (remove .txt from the end of filename). One is for the front doors, the other for the rears. The rear door skins had a different ID is why.


x1RDMTT.jpg

ZnPv47l.jpg

XeWBcgo.jpg

NyrVjMm.jpg

vh9lkHM.jpg

rtK3G4m.jpg
 

Attachments

  • Front Door Plug Grommet.stl.txt
    80.7 KB · Views: 7
  • Rear Door Plug Grommet.stl.txt
    81.7 KB · Views: 1
Last edited:
Now that I live in Florida I've learned people like to drive up to Georgia and pretend those are mountains. Buuuttt when you're used to ant hills I'm sure regular hills sure do seem big. 😂
My wife is from Tampa(Plant Shitty actually) and all of her Aunt's and Uncle's seem to be retiring and building houses in NW Georgia mountains. So I know what you mean lol.
 
My wife is from Tampa(Plant Shitty actually) and all of her Aunt's and Uncle's seem to be retiring and building houses in NW Georgia mountains. So I know what you mean lol.
The YUGE 1500 ft mountains - lol. In terms of the lights, I used upfitter 2 (ignition dependent) but I may move it to 5/6 later depending on how I end up using them... right now it is dark backup and hooking up a trailer or 2 which both would be truck on anyway.
 
Finally got my truck back today. 6.7HO King Ranch.

Put the Winch on the truck from Ford

CARLI 2023 FORD SUPER DUTY E-VENTURE ELECTRONIC (2.5"/3.5" LIFT) SUSPENSION SYSTEM

Torsion Sway Bar with End link Leveling
Standard Carli Soft ride leaf pack and leaf spring shackle
Air bags on back to level with air compressor
Fabricated Radius Arms
High Mount Steering Stabilizer
Low Mount Steering Stabilizer

Method Racing 20 wheels and tires
AMP retractable Running Boards
Have the Baja style light kit wired and my fab shop is making mounting brackets. Will be on soon.
Have the Weather Tech mud flaps coming


processed-66A9D174-FE0D-40C7-AEC3-C032463F70D8.jpeg


processed-9FF1EA5C-8F1A-4843-99A7-D36B1A133E29.jpeg
 
Finally got my truck back today. 6.7HO King Ranch.

Put the Winch on the truck from Ford

CARLI 2023 FORD SUPER DUTY E-VENTURE ELECTRONIC (2.5"/3.5" LIFT) SUSPENSION SYSTEM

Torsion Sway Bar with End link Leveling
Standard Carli Soft ride leaf pack and leaf spring shackle
Air bags on back to level with air compressor
Fabricated Radius Arms
High Mount Steering Stabilizer
Low Mount Steering Stabilizer

Method Racing 20 wheels and tires
AMP retractable Running Boards
Have the Baja style light kit wired and my fab shop is making mounting brackets. Will be on soon.
Have the Weather Tech mud flaps coming


View attachment 136121

View attachment 136122
What did you do about the leveling sensor in the front?
 
What did you do about the leveling sensor in the front?
We were able to modify the stock bracket. Carley is currently making one for sale. When that's up for sale I am going to purchase and install.
 
We were able to modify the stock bracket. Carley is currently making one for sale. When that's up for sale I am going to purchase and install.
Could you post a pic of the modified bracket please? I am trying to figure that one out myself and I don’t want to spend 200 bucks on one from Wicked.
 
I never liked how this lariat sticker thing stood out from the otherwise black badge. And now i noticed that in a little while it will probably just fall off on its own, pressing it i felt the pops inside and i know exactly what it means. So i gently pried it off, off course there’s water and thats whats causing glue separation.

i’m going to paint it black just not sure what to use, maybe plastidip for the win?

IMG_0594.jpeg
IMG_0595.jpeg
IMG_0596.jpeg
IMG_0597.jpeg



Even without the sticker it just looks so much cleaner.

IMG_0599.jpeg
 
Back
Top