Running board lights

[Mickleford]

Hey guys I’m wanting to add running board strip LEDs to the rocker panels on my 2021 lariat. I’ve searched everywhere and found that there are factory plugs either on the frame under the rear doors or under the sill plates at the front doors that everyone uses. Unfortunately my truck has neither of these.

Does anyone have a wiring diagram or knowledge of where and how to tap into the puddle light circuit to provide power?

Thanks

 

[Nyvall]

Yep Ill be doing this shortly. Check out this video.

 

[Nyvall]

Yep Ill be doing this shortly. Check out this video.

I think I miss read your post my apologies. Not sure why it wouldn't be there.

 

[Duke]

i found my connectors under the plastic sill plate between the door & seat. it is snapped into a plastic clip right next to the wiring and has an end plug on it.

 

[Mickleford]

Yes, unfortunately my truck doesn’t have them.

 

[Duke]

ok i know 1 wire is white & the other wire is black with a purple line . maybe you can check the wiring harness for the 2 wires & test them

 

[Mickleford]

ok i know 1 wire is white & the other wire is black with a purple line . maybe you can check the wiring harness for the 2 wires & test them

Ok thanks! I’ll check it out

 

[Mickleford]

@Duke are those wire colors the same on both sides?

 

[bgmspd]

If no one beats me to it, I'll pop the sill plates tomorrow and send you pics of the wire colors from the connectors.

 

[Mickleford]

If no one beats me to it, I'll pop the sill plates tomorrow and send you pics of the wire colors from the connectors.

Thank you!

 

[Duke]

Ok thanks! I’ll check it out

yes the wires are the same colors. i pulled the end plug off & tested the connector it worked just like in the colts way video. i than put the wires thru the end plug so it was a tight fit. i ran the wires thru a rubber plug in the floor board to the led strip.

 

[Mickleford]

yes the wires are the same colors. i pulled the end plug off & tested the connector it worked just like in the colts way video. i than put the wires thru the end plug so it was a tight fit. i ran the wires thru a rubber plug in the floor board to the led strip.

Thanks. I’ll look for them tomorrow

 

[Donnie With A Dee]

i found my connectors under the plastic sill plate between the door & seat. it is snapped into a plastic clip right next to the wiring and has an end plug on it.View attachment 13239View attachment 13240

Front seat or back seat? Driver or passenger side? Thanks.

 

[Patriot]

Yep Ill be doing this shortly. Check out this video.

Colt is a funny dude..he gets it done one way or the other.

 

[Nyvall]

Colt is a funny dude..he gets it done one way or the other.

Yep

 

[Duke]

Front seat or back seat? Driver or passenger side? Thanks.

both side in the front if you lift the front rug up a little there is a rubber plug i just put a small hole thru it & ran the 2 wires thru

 

[Donnie With A Dee]

both side in the front if you lift the front rug up a little there is a rubber plug i just put a small hole thru it & ran the 2 wires thru

Thanks! I look for it.

 

[Mdel1189]

Hey guys I have a 2021 f250 and I popped that plate and found the two wires (black with purple and white) but when I went to the passenger side those wires are not there can anyone help me out as to Wah at wires I should use? Want to use the dome lights

 

[Duke]

Hey guys I have a 2021 f250 and I popped that plate and found the two wires (black with purple and white) but when I went to the passenger side those wires are not there can anyone help me out as to Wah at wires I should use? Want to use the dome lights

are you sure the plug with the wires is not taped up in the harness?

 

[Himni]

Any one find a good place on the 21s to tap in to for running board lights?