Can we fit a Side x Side in the box of these Tremors ?

R32GT-R

Tremor Fiend
Joined
May 24, 2021
Messages
471
Reaction Points
815
Location
Calgary, AB
Current Ride
2022 F350 King Ranch Ultimate 6.7 Tremor - Antimatter/Stone
Current Ride #2
1998 Nissan Patrol/Safari TD42t - i6 IDI, 1989 Nissan R32 GT-R
wouldn't mind transitioning out of a current hobby and into a side x side.. can we fit one in our boxs ? was looking for a three or four seater.. always been a fan of Honda and Yamaha
 
according to iseecars the width between the wheelhouses is 50.5 inches. if you can go above them the tailgate opening is 60.5 inches (the box is slightly wider itself at 66.9 inches). and total bed length is 81.9 inches. that may help you in your search!

 
Did you ever get answer to this? My Tremor arrives in two weeks. Fingers crossed my 60in wide wildcat sport fits.
 
Buy a dirtbike instead. Too many idiots in SxS’s already
i live in canada, we have alot more space.. and i want to use it for hunting, i would install a full cab and heater.
 
i live in canada, we have alot more space.. and i want to use it for hunting, i would install a full cab and heater.
Currently hunting elk in archery season off a TE300i. It’s pretty cool but riding with a 50lb pack kinda sucks! Basically ride in, hide bikes, hike a couple miles, set camp, hunt. Planning on throwing a quarter over each side of the gas tank if we get one. Definitely jealous of a side by side for hunting although I wouldn’t be able to access the same trails.
 
Last edited:
I have no personal experience with it but a guy I follow on YouTube (Last Line Of Defense) has a bed cover on the Tremor he built that's supposed to support a side by side. It's from a company named Diamondback Truck Covers. It's what I'm going to put on mine, when I get one. Hope this helps!
 
I have no personal experience with it but a guy I follow on YouTube (Last Line Of Defense) has a bed cover on the Tremor he built that's supposed to support a side by side. It's from a company named Diamondback Truck Covers. It's what I'm going to put on mine, when I get one. Hope this helps!

There’s someone here who hauls a UTV on a Diamondback. I can’t recall whom but I think there were photos in one of the TOTM threads in the past few months.
 
6714FDBC-15BA-4AE6-8EC1-CF09175DCDBE.webp
C2D3C7CA-6080-49D2-952F-5A38D780A845.webp
64FF64DC-00A2-44FE-9D53-522FA038FC2F.webp

Honda Pioneer 500 fits OK anything much wider than 50” will have to go over the wheel wells the 50” Pioneer is tight. Also takes some getting used to driving up the ramps. I cheated and used the loading doc at the dealer when I picked up my Dads Pioneer but unloaded and reloaded with the ramps. I would not haul it many times like this had to climb out of the Honda since couldn’t get the door open. Lots of climbing around the box to tie it down. I normally trailer SxS and put ATVs in the box but had my trailer tied up with another load so thought I would give it a shot and it does work in a pinch but it’s much easier to trailer.
 
View attachment 33913View attachment 33914View attachment 33915
Honda Pioneer 500 fits OK anything much wider than 50” will have to go over the wheel wells the 50” Pioneer is tight. Also takes some getting used to driving up the ramps. I cheated and used the loading doc at the dealer when I picked up my Dads Pioneer but unloaded and reloaded with the ramps. I would not haul it many times like this had to climb out of the Honda since couldn’t get the door open. Lots of climbing around the box to tie it down. I normally trailer SxS and put ATVs in the box but had my trailer tied up with another load so thought I would give it a shot and it does work in a pinch but it’s much easier to trailer.
This is exactly what i was thinking... a Honda Pioneer. And it fits, thanks a bunch
 
Back
Top